Planet ERT-805 User manual

Table of Contents
Chapter 1 Package Contents 1
Unpacking the router 1
Hardware install section 2
Connect a Serial Device 2
Chapter 2 Terminal Setup 3
Chapter 3 Logon to the Console 5
Chapter 4 Configure Password 7
Chapter 5 Configuration IP Address 9

1
This page is intentionally left blank

1
Chapter 1
Package Contents
Thank you for purchasing ERT-805 Serial WAN Router.
This installation guide provides the basic information of the router, ERT-805, including,
hardware installation, console interface login and LAN interface setup. For more
information of the router, please also refer to the user’s manual of the router in the CD-
ROM.
Unpacking the router
Open the box of the ERT-805 router and carefully unpack it. The box should contain the
following items:
• ERT-805 Serial WAN Router
• Power Cord
• DB9 to RJ-45 changer
• RJ-45 to RJ-45 modem cable
• User’s Manual CD
• Quick installation Guide
 Note:
if any item is found missing or damaged, please contact your local
reseller immediately.

2
3
Hardware install section
To install ERT-805 serial router, just following the step:
• Connect an Ethernet device
• Connect a Serial device
• Connect a terminal or PC
• Connect the power supply
Connect a Serial Device
WAN Option WAN Encapsulation
Frame relay
X.25
Link control (HDLC) or ppp
Frame-relay
X.25

2
3
Chapter 2
Terminal Setup
To congure the system, connect the provided RJ-45 cable and DB9 connector to a COM
port on a PC or notebook computer and to serial (console) port of the device.
When the connection between the PC and ERT-805 is ready, run the Hyper Terminal and
congure its communication parameters. It can be accessed from the Start menu. Click
START, then Programs, Accessories and then Hyper Terminal.
The operating mode of the console port is:
• Baud rate: 9600
• Data bits: 8
• Parity: none
• Stop bits: 1
• Flow control: None
After nished the setting, click OK.
Or run the Mrcom32.exe under DOS mode (The program can be found in the CD-ROM,
directory “/utility”). It can access from START menu click RUN then type “e:/utility/
mrcom32 com1 9600” where assume ‘e’ drive is the CD-ROM drive.

4
5
This page is intentionally left blank

4
5
Chapter 3
Logon to the Console
Once the terminal has connected to the device, power on the device, the terminal will
display that it is running POST (Power on self-test) procedures.
Then, screen as below will show up. The ERT-805 will prompt with “>”. This means ERT-
805 is in operating mode now.
Types “enable” to enter privilege mode. The ERT-805 will prompt with “#” for privilege
mode. By default there is no password.
 Note:
For security reason, please follow the following section to change
the new password after this rst setup. Memorize the password
or write it down and store in a secured place.

6
7
This page is intentionally left blank

6
7
Chapter 4
Configure Password
1. Once log on to the console, the following screen displayed.
Fig 1: The privilege Screen of ERT-805
2. Types “cong terminal” to enter conguration mode. ERT-805 will prompt
“<console>#”
Fig 2: Conguration mode Screen
3. Then type command enable password “abc” to setup the enable privilege password
where abc is the password. ( password can be any alphabetic or numerical with up
to 16 ASCII character is allowed)
Fig 3: conguration for password
4. Key in “end” to close the congure mode and key in “wr” to store the setting and
make the setting activated right away.

8
9
This page is intentionally left blank

8
9
Chapter 5.
Configuration IP Address
Follow the step 1 to step 2 on above to go into congure mode. Then type “int s0/0” or
“int Fastethernet 0/0”. After get into the interface, type ip address “ip address” “subnet
mask”. For example: ip address 192.168.99.64 255.255.255.0
Fig 4 IP conguration
And key in “end” to close the congure mode and “wr” to write the setting and make the
setting activated right away.
Now ERT-805 is with a IP address and ready to have further conguration, You can either
stay in the console interface for setup or using Telnet too.
Please refer to the user’s manual to have further conguration.

10
This page is intentionally left blank

10

2010-000033-000