Planet IGS-4215-4P4T User manual

Industrial L2/L4 Managed Gigabit Switch
with 4/8-Port 802.3at PoE+
IGS-4215-4P4T/IGS-4215-4P4T2S/IGS-4215-8P2T2S
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Wiring the Power Inputs.............................................................................. 5
4. Terminal Setup ........................................................................................... 7
5. Logon to the Console .................................................................................. 8
6. ConguringIPAddressviatheConsole ........................................................ 9
7. SavingtheCongurationviatheConsole.....................................................11
8. Starting Web Management .........................................................................12
9. SavingCongurationviatheWeb ...............................................................14
10.RecoveringBacktoDefaultConguration ....................................................15
11. Customer Support.....................................................................................16

3
1. Package Contents
Thank you for purchasing PLANET L2/L4 Managed Gigabit Switch. The description
ofthismodelisshownbelow:
IGS-4215-4P4T  Industrial 4-Port 10/100/1000T 802.3at PoE + 4-Port
10/100/1000TManagedSwitch
IGS-4215-4P4T2S  Industrial 4-Port 10/100/1000T 802.3at PoE + 4-Port
10/100/1000T+2-Port100/1000XSFPManagedSwitch
IGS-4215-8P2T2S  Industrial 8-Port 10/100/1000T 802.3at PoE + 2-Port
10/100/1000T+2-Port100/1000XSFPManagedSwitch
“Industrial Managed PoE+ Switch” isusedasanalternativenamein thisQuick
InstallationGuide.
Open the box of the Industrial Managed PoE+ Switch and carefully unpack it. The
boxshouldcontainthefollowingitems:
zTheIndustrialManagedPoE+Switchx1
zQuickInstallationGuidex1
zRS232 to RJ45 Console Cable x 1
zDustCaps
Model RJ45DustCaps SFPDustCaps
IGS-4215-4P4T 9-
IGS-4215-4P4T2S 9 2
IGS-4215-8P2T2S 11 2
zDIN-railKitx1
zWallMountingKitx1
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Requirements
Workstations running Windows XP/2003/Vista/7/8/10/2008, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
WorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
SerialPortConnection(Terminal)
 The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
 The above Workstations have been installed with terminal emulator, such as
HyperTerminalincludedinWindowsXP/2003.
 Serial cable -- one end is attached to the RS232 serial port, while the other
endstotheRJ45consoleportoftheIndustrialManagedPoE+Switch.
EthernetPortConnection
 Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
 The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Industrial Managed PoE+ Switch. If the Web interface of the
Industrial Managed PoE+ Switch is not accessible, please turn off
theanti-virussoftwareorfirewallandthentryitagain.

5
3. Wiring the Power Inputs
TheUpper Panelofthe IndustrialManaged PoE+ Switchindicates aDCinlet power
socketandconsistsofoneterminalblockconnectorwithin6contacts.Pleasefollow
the steps below to insert the power wire.
1.Insert positive/negative DC power wires into contacts 1 and 2 for Power 1 or 5,
and6forPower2.
IGS-4215-4P4T/IGS-4215-4P4T2S: DC 48~56V
Input DC 48~56V
V1- V1+
DC1
V2- V2+
DC2
Fault
1A@24V
1 2 3 4 5 6
Figure 3-1: IGS-4215-4P4T/IGS-4215-4P4T2S DC Inlet Power Socket
IGS-4215-8P2T2S: DC 48~56V
Input DC 48V~56V
DC1 DC2
Fault
1A@24V
1 2 3 4 5 6
Figure 3-2: IGS-4215-8P2T2S DC Inlet Power Socket

6
2.Tightenthewire-clampscrewsforpreventingthewiresfromloosening.
1 2 3 4 5 6
V1- V1+ V2- V2+
Power 1 Power 2
Item Negative(-)Pin Positive(+)Pin
IGS-4215-4P4T/IGS-4215-4P4T2S Pin1/5 Pin2/6
1 2 3 4 5 6
V+ V- V+ V-
Power 1 Power 2
Item Positive(+)Pin Negative(-)Pin
IGS-4215-8P2T2S Pin1/5 Pin2/6
Note
The wire gauge for the terminal block should be in the range from
12 to 24 AWG.

7
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to the RJ45 type of the console port of the Industrial
ManagedPoE+Switch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 4-1: Industrial Managed PoE+ Switch Console Connectivity
A terminal program is required to make the software connection to the Industrial
ManagedPoE+Switch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Baud: 115200
Databits: 8
Parity: None
Stopbits: 1
Flowcontrol: None
Figure 4-2: COM Port Conguration

8
5. Logon to the Console
Once the terminal is connected to the device, power on the Industrial Managed
PoE+ Switch and the terminal will display “running testing procedures”. Then, the
following message asks to login user name and password. The factory default
user name and password are shown as follows, and the login screen in Figure 5-1
appears.
Note
The following console screen is based on the IGS-4215-8P2T2S.
ThedisplayoftheIGS-4215-4P4TorIGS-4215-4P4T2Sisthesame
asthatoftheIGS-4215-8P2T2S.
Username:admin
Password:admin
Figure 5-1: Industrial Managed PoE+ Switch Console Login Screen
The user can now enter commands to manage the Industrial Managed PoE+
Switch. For a detailed description of the commands, please refer to the following
chapters.
Note
1.For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-
face.

9
6.ConguringIPAddressviatheConsole
TheIndustrialManagedPoE+SwitchisshippedwithdefaultIPaddressasfollows:
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the Industrial
ManagedPoE+Switch,pleaseusetheproceduresasfollows:
Show the current IP address
1.Atthe“IGS-4215-8P2T2S#”prompt,enter“show ip”.
2.The screen displays the current IP address, subnet mask and gateway as shown
inFigure6-1.
Figure 6-1: IP Information Screen
 ConguringIPaddress
3.Atthe“IGS-4215-8P2T2S #”prompt,enter“congure”.
4.At the “IGS-4215-8P2T2S (cong)#” prompt, enter the following command
andpress<Enter>asshowninFigure6-2.
IGS-4215-8P2T2S(cong)#ip address 192.168.1.100 mask 255.255.255.0
IGS-4215-8P2T2S(cong)#ip default-gateway 192.168.1.254
The previous command would apply the following settings for the Industrial
ManagedPoE+Switch.
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.254

10
Figure 6-2: IP Address Screen
5.RepeatStep1tocheckiftheIPaddressischanged.
If the IP is successfully congured, the Industrial Managed PoE+ Switch will apply
the new IP address setting immediately. You can access the Web interface of the
IndustrialManagedPoE+SwitchthroughthenewIPaddress.
Note
Ifyouarenotfamiliarwithconsolecommandortherelatedparam-
eter,enter“?”anytimeinconsoletogetthehelpdescription.

11
7.SavingtheCongurationviatheConsole
In the Industrial Managed PoE+ Switch, the running conguration le is stored in
the RAM. In the current version, the running conguration sequence of running-
cong can be saved from the RAM to FLASH by copying the running-cong
startup-cong command, so that the running conguration sequence becomes
thestartupcongurationle,whichiscalledcongurationsave.
1.At the “IGS-4215-8P2T2S#” prompt, enter “copy running-cong startup-
cong”asshowninFigure7-1
Figure 7-1: The Conguration Save Screen

12
8. Starting Web Management
The following shows how to start up the Web Management of the Industrial
Managed PoE+ Switch. Note the Industrial Managed PoE+ Switch is congured
through an Ethernet connection. Please make sure the manager PC must be set to
the same IP subnet address.
For example, the default IP address of the Industrial Managed PoE+ Switch is
192.168.0.100, then the manager PC should be set to 192.168.0.x (where x
is a number between 1 and 254, except 100), and the default subnet mask is
255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address: 192.168.0.100
Figure 8-1: IP Management Diagram
Logging in to the Industrial Managed PoE+ Switch
1.Use Internet Explorer 8.0 or above Web browser and enter IP address
http://192.168.0.100toaccesstheWebinterface.
2.When the following dialog box appears, please enter the default user name and
password“admin”.TheloginscreeninFigure8-2appears.
DefaultUsername:admin
DefaultPassword:admin
Figure 8-2: Web Login Screen

13
3.Afterenteringthepassword,themainscreenappearsasFigure8-3shows.
Note
The following web screen is based on the IGS-4215-8P2T2S. The
display of the IGS-4215-4P4T or IGS-4215-4P4T2S is the same as
thatoftheIGS-4215-8P2T2S.
Figure 8-3: Web Main Screen of Industrial Managed PoE+ Switch
The Switch Menu on the left of the Web page lets you access all the commands
andstatisticstheIndustrialManagedPoE+Switchprovides.
Figure 8-4: Switch Menu
Now, you can use the Web management interface to continue the Switch
management.Pleaserefertotheuser’smanualformore.

14
9.SavingCongurationviatheWeb
In the Industrial Managed PoE+ Switch, the running conguration le is stored in
the RAM. In the current version, the running conguration sequence of running-
cong can be saved from the RAM to FLASH by “Save Congurations to
FLASH”function,sothat therunning congurationsequence becomes thestartup
congurationle,whichiscalledcongurationsave.
To save all applied changes and set the current conguration as a startup
conguration, the startup-conguration le will be loaded automatically across a
system reboot.
1.Click “Save > Save Congurations to FLASH” to log in to the “Conguration
Manager”page.
2. Press the “Apply” button to save running conguration to start up congura-
tion.

15
10.RecoveringBacktoDefaultConguration
IP Address has been changed or admin password has been
forgotten –
To reset the IP address to the default IP Address “192.168.0.100” or reset the
login password to default value, press the hardware reset button on the front
panel for about 10 seconds. After the device is rebooted, you can log in the
managementWebinterfacewithinthesamesubnetof192.168.0.xx.
RESET
IGS-4215-4P4T2S
109
100/1000X SFP
Console
115200,N,8,1
P1 P2 FAULT
120
90
60
30
PoE Power
Usage (W)
ACT
LNK
9
LNK/ACT1000LNK/ACT1000
10
8
6
7
5
10/100/1000T
43
1 2
ACT
LNK
1000
ACT
LNK
PoE In-Use
802.3at PoE
Figure 10-1: IGS-4215-4P4T/IGS-4215-4P4T2S Reset Button
IGS-4215-8P2T2S
7
5
3
1
RESET
Console
115200,N,8,1
P1 P2 FAULT
11
9
12
10
ACT1000 LNK
ACT100 LNK
8
10/100/1000T
6
4
2
LNK
PoE In-Use
ACT
802.3at PoE+
240W
PoE Power Usage
180W
120W
60W
Figure 10-2: IGS-4215-8P2T2S Reset Button

16
11. Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ
resourceandUser’s ManualonPLANETWebsite rsttocheckifit could solveyour
issue.Ifyouneed moresupportinformation,pleasecontact PLANETswitchsupport
team.
PLANETonlineFAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switchsupportteammailaddress:
[email protected]
IGS-4215-4P4T/IGS-4215-4P4T2S/IGS-4215-8P2T2SUser’sManual:
http://www.planet.com.tw/en/support/download.php?type1=22153&model=&type=3
(PleaseselectyourswitchmodelnamefromtheProductModeldrop-downmenu)
Copyright ©PLANET Technology Corp. 2017.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their
respective owners.