Planet IGS-6325-16T4X User manual

Industrial L3 Multi-Port Gigabit
Managed Ethernet Switch
IGS-6325 DIN-rail Series
Quick Installation Guide

Table of Contents
1. Package Contents................................................................................. 3
2. Requirements....................................................................................... 5
3. Wiring the Power Inputs ....................................................................... 6
3.1 Grounding the Device..................................................................... 9
4. Terminal Setup................................................................................... 10
4.1 Logging on to the Console............................................................ 11
 4.2 ConguringIPAddressviaConsole ............................................... 12
5. Starting Web Management .................................................................. 14
5.1 Logging in to the Industrial Managed Switch .................................. 15
 5.2 SavingCongurationviaWeb ....................................................... 17
6. RecoveringBacktoDefaultConguration ............................................. 18
7. Customer Support .............................................................................. 20

3
1. Package Contents
Thank you for purchasing PLANET L3 Industrial Managed Switch, IGS-6325
DIN-railseries.Thedescriptionsofthesemodelsareasfollows:
IGS-6325-16P4S IndustrialL316-Port10/100/1000T802.3atPoE+
4-Port100/1000XSFPManagedEthernetSwitch
IGS-6325-16T4S IndustrialL316-Port10/100/1000T+4-Port100/1000X
SFPManagedEthernetSwitch
IGS-6325-16T4X IndustrialL316-Port10/100/1000BASE-T+4-Port
10GBASE-XSFPManagedSwitch
IGS-6325-8T4X IndustrialL316-Port10/100/1000T+4-Port100/1000X
SFPManagedEthernetSwitch
IGS-6325-8T8S IndustrialL316-Port10/100/1000BASE-T+4-Port
10GBASE-XSFPManagedSwitch
IGS-6325-8T8S4X IndustrialL38-Port10/100/1000T+8-Port100/1000X
SFP+4-Port10GSFP+ManagedEthernetSwitch
IGS-6325-8UP2S IndustrialL38-Port10/100/1000T802.3btPoE+2-Port
1G/2.5GSFPManagedEthernetSwitch
IGS-6325-8UP2S2X
IndustrialL38-Port10/100/1000T802.3btPoE+2-Port
1G/2.5GSFP+2-Port10GSFP+ManagedEthernet
Switch
“Industrial Managed Switch” mentioned in this Quick Installation Guide
refers to the above models.

4
Open the box of the Industrial Managed Switch and carefully unpack it. The
boxshouldcontainthefollowingitems:
The
Industrial
Managed
Switch
DB9 to RJ45
Interface
RS232
Console Cable
Quick
Installation
Guide sheet
Wall
Mounting
Kit
RJ45
Dust
Cap
SFP
Dust
Cap
IGS-6325-
16P4S     17 4
IGS-6325-
16T4S     17 4
IGS-6325-
16T4X     17 4
IGS-6325-
8T4X     9 4
IGS-6325-
8T8S     9 8
IGS-6325-
8T8S4X     912
IGS-6325-
8UP2S     9 2
IGS-6325-
8UP2S2X     9 4
If any of these are missing or damaged, please contact your dealer
immediately. If possible, retain the carton including the original packing
materials to enable you to repack the product in case there is a need to return
it to us for repair.

5
2. Requirements
The Industrial Managed Switch provides remote login interface for
management purposes. The following equipment is necessary for further
management:
zWorkstations running Windows XP/2003/7/10/11, MAC OS 10.15 or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPProtocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard).
zSerial Port Connection(Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
The above Workstations have been installed with terminal emulator,
suchasHyperTerminalincludedinWindowsXP/2003,puttyorteraterm.
Serial cable -- one end is attached to the RS232 serial port, while the
other end to the console port of the Industrial Managed Switch.
zEthernet Port Connection
Network cables -- Use standard network (UTP) cables with RJ45
connectors.
The above PC is installed with Web browser.
It is recommended to use Chrome 98.0.xxx or above to access
the Industrial Managed Switch.

6
3. Wiring the Power Inputs
The Upper Panel of the Industrial Managed Switch indicates an inlet power
socket and consists of one green terminal block connector within 6 contacts.
Please follow the steps below to insert the power wire.
Insert positive/negative DC power wires into Contacts 1 and 2 for Power 1, or
Contacts 5 and 6 for Power 2.
IGS-6325-16P4S: DC48-56V
DI 0DI 1DO 0DO 1GND GND
Fault
V1+ V2+1A@24V
DC2DC1
Dual power input is required
for maximum PoE loading.
Refer to user’s manual for
more details.
Input: 48-56V , 7.5A max.
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-1: IGS-6325-16P4S Upper Panel
IGS-6325-16T4S:DC9-48V,AC24V
DI1 DO0 DO1DI0 GNDGND
Max. fault loading: 24V, 1A
DC Input: 9-48V , 3.3A max.
AC Input: 24V
, 1.2A max.
V1+ V2+
PWR1 PWR2Fault
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-2: IGS-6325-16T4S Upper Panel

7
IGS-6325-16T4X:DC9-48V,AC24V
DI1DO0DO1 DI0GNDGND
DC Input: 9-48V , 3.3A max.
AC Input: 24V
, 2A max.
V1+ V2+
PWR1 PWR2Alarm
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-3: IGS-6325-16T4X Upper Panel
IGS-6325-8T4X/IGS-6325-8T8S/IGS-6325-8T8S4X: DC 12~48V, AC 24V
DI1 DO0 DO1DI0 GNDGND
Max. fault loading: 24V, 1A
V1+ V2+
PWR1 PWR2Fault
DC Input: 12-48V , 4A max.
AC Input: 24V , 2A max.
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-4: IGS-6325-8T4X/IGS-6325-8T8S/IGS-6325-8T8S4X Upper Panel

8
IGS-6325-8UP2S/IGS-6325-8UP2S2X: DC 48~54V
DI1 DO0 DO1DI0 GNDGND
DC Input:
48-54V , 8.5A max.
Dual power input is required
for maximum PoE loading.
Refer to user’s manual for
more details.
PWR1 Alarm PWR2
V1+ V2+
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-5: IGS-6325-8UP2S/IGS-6325-8UP2S2X Upper Panel
Tightenthewire-clampscrewsforpreventingthewiresfromloosening.
123456
V+ V- V+ V-
Power 1 Power 2
Figure 3-6: The pin of 6-contact terminal block connector
1. The wire gauge for the terminal block should be in the range
from 12 to 24 AWG.
2.Please check the wire AWG Ampere specification before
connectingPLANETIndustrialManagedSwitch.
PWR1 and PWR2 must provide the same DC voltage for power
load balance while operating with dual power input.

9
3.1 Grounding the Device
Users MUST complete grounding wired with the device; otherwise, a sudden
lightning could cause fatal damage to the device.
DI 0DI 1DO 0DO 1GND GND
Fault
V1+ V2+1A@24V
DC2DC1
Dual power input is required
for maximum PoE loading.
Refer to user’s manual for
more details.
Input: 48-56V , 7.5A max.
1 2 3 4 5 6
1 2 3 4 5 6
Earth Ground

10
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to RJ45 type serial (console) port of the Industrial
Managed Switch.
PC/Workstation with
Terminal Emulation Software
RJ45 to DB9 RS232 Cable
Serial Port
Console Port
115200,N,8,1
IGS Industrial Managed Switch
Console
115200,N,8,1
A terminal program is required to make the software connected to the
Industrial Managed Switch.
1. Run terminal program on the OS.
2.When the following screen appears, makesurethat the COM port should be
conguredas:
Baud:115200
Parity:None
Databits:8
Stopbits:1
Flowcontrol:None