Planet IGS-6325-16P4S User manual

Industrial L3 Multi-Port Gigabit
Managed Ethernet Switch
IGS-6325-16P4S/IGS-6325-8T4X/IGS-6325-8T8S4X
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Wiring the Power Inputs.............................................................................. 5
4. Terminal Setup ........................................................................................... 7
4.1 Logging on to the Console.................................................................... 8
 4.2 ConguringIPAddressviaConsole ....................................................... 9
 4.3 Storingcurrentswitchconguration .....................................................10
5. Starting Web Management .........................................................................11
 5.1 LoggingintotheIndustrialManagedSwitch.........................................11
 5.2 SavingCongurationviaWeb ..............................................................14
6. RecoveringBacktoDefaultConguration.....................................................15
7. Customer Support .....................................................................................16

3
1. Package Contents
Thankyouforpurchasing PLANETL3Industrial ManagedSwitch,IGS-6325 DIN-rail
series.Thedescriptionsofthesemodelsareasfollows:
IGS-6325-16P4S
IndustrialL316-Port10/100/1000T802.3atPoE+4-Port
100/1000XSFPManagedEthernetSwitch
(-40~75degreesC)
IGS-6325-8T4X IndustrialL38-Port10/100/1000T+4-Port10GSFP+
ManagedEthernetSwitch(-40~75degreesC)
IGS-6325-8T8S4X
IndustrialL38-Port10/100/1000T+8-Port100/1000X
SFP+4-Port10GSFP+ManagedEthernetSwitch
(-40~75degreesC)
“Industrial Managed Switch” mentioned in this Quick Installation Guide refers to
theabovemodels.
Open the box of the Industrial Managed Switch and carefully unpack it. The box
shouldcontainthefollowingitems:
IGS-6325-16P4S IGS-6325-8T4X IGS-6325-8T8S4X
TheIndustrial
ManagedSwitch   
DB9toRJ45
InterfaceRS232
Console Cable
  
QuickInstallation
Guide   
Wall Mounting Kit   
RJ45DustCap 17 9 9
SFPDustCap 4 4 12
Ifanyof theseare missingor damaged,please contactyourdealer immediately.If
possible, retain the carton including the original packing materials to enable you to
repacktheproductincasethereisaneedtoreturnittousforrepair.

4
2. Requirements
The Industrial Managed Switch provides remote login interface for management
purposes.Thefollowingequipmentisnecessaryforfurthermanagement:
zWorkstationsrunningWindows XP/2003/Vista/7/8/2008/10,MACOS X orlater,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPProtocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard).
zSerial Port Connection(Terminal)
 The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
 TheaboveWorkstations havebeen installedwith terminal emulator,suchas
HyperTerminalincludedinWindowsXP/2003,puttyorteraterm.
Serial cable -- one end is attached to the RS232 serial port, while the other
endtotheconsole portoftheIndustrialManagedSwitch.
zEthernetPortConnection
Network cables--Usestandardnetwork(UTP)cableswithRJ45connectors.
 The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explorer 8.0 or above to access
theIndustrialManagedSwitch.

5
3. Wiring the Power Inputs
The Upper Panel of the Industrial Managed Switch indicates a DC inlet power
socketandconsistsofoneterminalblockconnectorwithin6contacts.Pleasefollow
the steps below to insert the power wire.
1.Insert positive/negative DC power wires into Contacts 1 and 2 for Power 1, or
Contacts5and6forPower2.
IGS-6325-16P4S:DC48-56V
DI 0DI 1DO 0DO 1GND GND
Fault
V1+ V2+1A@24V
DC2DC1
Dual power input is required
for maximum PoE loading.
Refer to user’s manual for
more details.
Input: 48-56V , 7.5A max.
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-1: IGS-6325-16P4S Upper Panel
IGS-6325-8T4X/IGS-6325-8T8S4X:12~48VDC,24VAC
Input DC 12V~48V
AC 24V
DC1 DC2
Fault
1A@24V
DI1 DO0 DO1DI0 GNDGND
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-2: IGS-6325-8T4X/IGS-6325-8T8S4X Upper Panel

6
2.Tightenthewire-clampscrewsforpreventingthewiresfromloosening.
123456
V+ V- V+ V-
Power 1 Power 2
Model Positive(+)Pin Negative(-)Pin
IGS-6325-16P4S
Pin1/5 Pin2/6IGS-6325-8T4X
IGS-6325-8T8S4X
Figure 3-3: The pin of 6-contact terminal block connector
Note
The wire gauge for the terminal block should be in the range from
12 to 24 AWG.
Please check the wire AWG Ampere specification before connecting
PLANETIndustrialManagedSwitch.

7
4. Terminal Setup
Tocongure the system,connectaserialcable toaCOMporton aPCornotebook
computerandtoRJ45typeserial(console)portoftheIndustrialManagedSwitch.
Console Port
115200,N,8,1
RJ45 to DB9 RS232 Cable
PC/Workstation with
Terminal Emulation Software
IGS Industrial Managed Switch
Serial Port
A terminal program is required to make the software connected to the Industrial
ManagedSwitch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Baud:115200
Parity:None
Databits:8
Stopbits:1
Flowcontrol:None

8
4.1 Logging on to the Console
Once the terminal has been connected to the device, power on the Industrial
ManagedSwitchandtheterminalwilldisplay“runningtestingprocedures”.
Note
The following console screen is based on the IGS-6325-16P4S.
The display of the IGS-6325 series is the same as that of the IGS-
6325-16P4S.
Then, the following message asks to log in user name and password. The factory
defaultusernameandpasswordare shownasfollowsastheloginscreen inFigure
4-1appears
UserName:admin
Password:admin
Figure 4-1: Console Login Screen
The user can now enter commands to manage the Industrial Managed Switch. For
adetaileddescriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new
password after this first setup.
2.Only accept command in lowercase letter under console inter-
face.

9
4.2 ConguringIPAddressviaConsole
TheIndustrialManagedSwitchisshippedwithdefaultIPaddressshownbelow:
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the Switch, please
usetheprocedureasfollows:
Display of the current IP Address
1.Atthe“#”prompt,enter“show ip interface brief”.
IGS-6325-Series # show ip interface brief
2.ThescreendisplaysthecurrentIPaddressshowninFigure4-2.
Figure 4-2: IP Information Screen
 CongurationoftheIPAddress
3.At the “#” prompt, enter the following command and press <Enter> as shown
inFigure4-3.
IGS-6325-Series#congureterminal
IGS-6325-Series(cong)# interface vlan 1
IGS-6325-Series(cong-if-vlan)# ip address 192.168.1.100 255.255.255.0

10
The previous command would apply the following settings for the Industrial
ManagedSwitch.
IPAddress:192.168.1.100
SubnetMask:255.255.255.0
Figure 4-3: Conguring IP Address Screen
4.Repeatstep1tocheckiftheIPaddresshaschanged.
4.3 Storingcurrentswitchconguration
1.Atthe“#”prompt,enterthefollowingcommandandpress<Enter>.
#copyrunning-congstartup-cong
Figure 4-4: Saving Current Conguration Command Screen
If the IP is successfully congured, the Industrial Managed Switch will apply the
new IP address setting immediately. You can access the Web interface of the
IndustrialManagedSwitchthroughthenewIPaddress.
Note
If you are not familiar with the console command or the related
parameter, enter “help” anytime in console to get the help
description.