Planet GS-6320-46S2C4XR User manual

L3 46-Port 100/1000BASE-X SFP + 2-Port Gigabit
TP/SFP + 4-Port 10G SFP+ Managed Switch
GS-6320-46S2C4XR
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Wiring the Power Inputs.............................................................................. 5
4. Terminal Setup ........................................................................................... 6
4.1 Logging on to Console ......................................................................... 7
 4.2 ConguringIPAddress......................................................................... 8
 4.3 StoringCurrentSwitchConguration....................................................10
5. Starting Web Management .........................................................................11
 5.1 LoggingintotheL3ManagedSwitch...................................................11
 5.2 SavingConguration...........................................................................14
6. RecoveringBacktoDefaultConguration.....................................................15
7. Customer Support .....................................................................................16

3
1. Package Contents
Thank you for purchasing PLANET L3 46-Port 100/1000BASE-X SFP + 2-Port
GigabitTP/SFP+4-Port10GSFP+ManagedSwitch,theGS-6320-46S2C4XR.
“L3 Managed Switch”mentionedin thisquickinstallation guiderefers to theGS-
6320-46S2C4XR.
Open the box of the L3 Managed Switch and carefully unpack it. The box should
contain the following items:
ModelName
Package Item GS-6320-46S2C4XR
TheL3ManagedSwitch 1
QuickInstallationGuide 1
RJ45 to RS232 Console Cable 1
RubberFeet 4
PowerCord 1
SFP Dust Caps 52
TwoRack-mountingBrackets
withAttachmentScrews 
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Requirements
zWorkstations running Windows XP/2003/2008/Vista/7/8/10, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard).
zSerial Port Connection (Terminal)
The above workstations come with COM port (DB9) or USB-to-RS232
converter.
 Theaboveworkstations havebeen installedwith terminal emulator,suchas
TeraTerm,PuTTYorHyperTerminalincludedinWindowsXP/2003.
Serial cable -- one end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheL3ManagedSwitch.
zEthernet Port Connection
 Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
 TheabovePCisinstalledwithWebbrowser.
Note
It is recommended to use Internet Explorer 8.0 or above to access
the L3 Managed Switch. If the Web interface of the L3 Managed
Switch is not accessible, please turn off the anti-virus software or
firewallandthentryitagain.

5
3. Wiring the Power Inputs
The rear panel of the L3 Managed Switch has an AC power socket, one DC power
on/oswitchandoneDCinletterminalblockwithin2screws.
49
10G/1G
50
10G/1G
51
10G/1G
52
10G/1G
ACT10G
ACT1G V+
DC Input Range
36-60V
, 2A max.
ON
OFF
DC POWER
50/60Hz
Ensure the power switch
in the “OFF” position
before connect the DC wire.
CAUTION 100-240V , 1.2A max.
Figure 3-1: L3 Managed Switch Rear Panel
DC Inlet Terminal Block
The DC inlet terminal block accepts DC power input voltage from 36V to 60V DC.
Connectthepowercabletothe L3ManagedSwitchattheDCinputterminal block;
the size of the two screws in the terminal block is M3.5.
Please follow the steps below to insert the DC power wire.
1.Insert the negative wire (Black) into the “V-” connector and tighten the wire-
clamp to prevent the DC wire from loosening.
2.Insert the positive wire (Red) into the “V+” connector and tighten the wire-
clamp to prevent the DC wire from loosening.
3.PowerontheL3ManagedSwitchbyswitchingittothe“ON” position.
V+
DC Input Range
36-60V
, 2A max.
ON
OFF
DC POWER
Ensure the power switch
in the “OFF” position
before connect the DC wire.
CAUTION
Figure 3-2: L3 Managed Switch DC Inlet Terminal Block
Warning
Before connecting the DC power cable to the input terminal block
of the L3 Managed Switch, make sure that the power switch is in
the “OFF”positionandtheDCpowerisOFF.
Note
The wire gauge for the terminal block should be in the range from
12 to 24AWG.

6
4. Terminal Setup
To congure the system, connect aserial cable to aCOM port ona PC ornotebook
computerandtotheDB9typeofRJ45serialportoftheL3ManagedSwitch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 4-1: L3 Managed Switch Console Connectivity
A terminal program, such as Tera Term or PuTTY, is required to make the software
connectiontotheL3ManagedSwitch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Baud:115200
Data bits: 8
Parity:None
Stop bits: 1
Flowcontrol:None
Figure 4-2: COM Port Conguration

7
4.1 Logging on to Console
Once the terminal is connected to the device, power on the L3 Managed Switch,
and the terminal will display “running testing procedures”. Then, the following
message asks to log in user name and password. The factory default user name
andpasswordareshownasfollowsandtheloginscreeninFigure4-3appears.
Username:admin
Password:admin
Figure 4-3: L3 Managed Switch Console Login Screen
The user can now enter commands to manage the L3 Managed Switch. For a
detaileddescriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Onlyacceptcommandinlowercaseletterunderconsoleinterface.

8
4.2 ConguringIPAddress
TheL3ManagedSwitchisshippedwithdefaultIPaddressshownbelow.
IPAddress:192.168.0.100
Subnet Mask: 255.255.255.0
To check the current IP address or modify a new IP address for the Switch, please
usetheproceduresasfollows:
Showing the Current IP Address
1.Atthe“#”prompt,enter“show ip interface brief”.
2.ThescreendisplaysthecurrentIPaddressasshowninFigure4-4.
Figure 4-4: IP Information Screen

9
ConguringIPAddress
3.At the “#” prompt, enter the following command and press <Enter> as shown
inFigure4-5.
GS-6320-46S2C4XR#congureterminal
GS-6320-46S2C4XR(cong)#interfacevlan1
GS-6320-46S2C4XR(cong-if-vlan)#ipaddress192.168.1.100255.255.255.0
Figure 4-5: Conguring IP Address Screen
The previous command would apply the following settings for the L3 Managed
Switch.
IPAddress:192.168.1.100
Subnet Mask: 255.255.255.0
4.Repeatstep1tocheckiftheIPaddressischanged.
If the IP is successfully congured, the L3 Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of the L3 Managed
SwitchthroughthenewIPaddress.

10
4.3 StoringCurrentSwitchConguration
In the L3 Managed Switch, the running conguration sequence running-cong
can be saved from the RAM to FLASH by “copy” command, so that the running
conguration sequence becomes the start-up conguration le, which is called
congurationsave.
Atthe“#”prompt,enterthefollowingcommandandpress<Enter>.
# copy running-cong startup-cong
Figure 4-6: Saving Current Conguration Command Screen
Note
If you are not familiar with the console command or the related
parameter, enter “help” anytime in console to get the help
description.