Planet XGS-5240-24X2QR User manual

Layer 2+ 24-Port 10G SFP+ + 2-Port 40G QSFP+
Managed Switch
XGS-5240-24X2QR
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Switch Management.................................................................................... 4
3. Requirements ............................................................................................. 5
4. Terminal Setup ........................................................................................... 6
4.1 Logging on to the Console.................................................................... 7
 4.2 ConguringIPAddress......................................................................... 8
 4.3 Setting1000BASE-Xfor10GSFP+Port................................................. 9
 4.4 ChangingPassword.............................................................................. 9
 4.5 SavingtheConguration ...................................................................... 9
5. Starting Web Management .........................................................................10
 5.1 LoggingintotheManagedSwitchfromManagementPort .....................11
 5.2 SavingCongurationviatheWeb ........................................................12
6. RecoveringBacktoDefaultConguration.....................................................13
7. Customer Support .....................................................................................14

3
1. Package Contents
Thank you for purchasing PLANET Layer 2+ 24-Port 10G SFP+ + 2-Port 40G
QSFP+ManagedSwitch,XGS-5240-24X2QR.
Unless specied, “Managed Switch” mentioned in this Quick Installation Guide
referstotheXGS-5240-24X2QR.
Open the box of the Managed Switch and carefully unpack it. The box should
containthefollowingitems:
zTheManagedSwitchx1
zQuickInstallationGuidex1
zRJ45-to-DB9ConsoleCablex1
zPowerCordx1
zRubberFeetx4
zTwoRack-mountingBracketswithAttachmentScrewsx6
zSFP+/QSFP+DustCapx26(installedonthemachine)
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Switch Management
To set up the Managed Switch, the user needs to congure the Managed Switch
fornetwork management.The ManagedSwitch providestwo managementoptions:
Out-of-Band ManagementandIn-Band Management.
Out-of-Band Management
Out-of-band management is the management through console interface. Generally,
the user will use out-of-band management for the initial switch conguration, or
whenin-bandmanagementisnotavailable.
In-Band Management
In-band management refers to the management by logging in to the Managed
Switchusing Telnetor HTTP,orusing SNMPmanagement softwaretocongure the
Managed Switch. In-band management enables the management of the Managed
SwitchtoattachsomedevicestotheSwitch.Thefollowingproceduresarerequired
toenablein-bandmanagement:
1. Log on to console
2.Assign/CongureIPaddress
3. Create a remote login account
4.EnableHTTPorTelnetserverontheManagedSwitch
In case in-band management fails due to Managed Switch conguration changes,
out-of-band management can be used for conguring and managing the Managed
Switch.
Important
The Managed Switch is shipped with Management Port IP address
192.168.1.1/24 assigned and VLAN1 interface IP address
192.168.0.254/24 assigned by default. User can assign another
IP address to the Managed Switch via the console interface to be
abletoremotelyaccesstheManagedSwitchthroughTelnetorHTTP.

5
3. Requirements
zWorkstations running Windows XP/2003/Vista/2008/7/8/10, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zSerial Port Connection(Terminal)
 The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
 The above Workstations have been installed with terminal emulator, such as
Tera Term or PuTTY.
 Serial cable -- one end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheManagedSwitch.
zManagement Port Connection
 Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
 TheabovePCisinstalledwithWebbrowser
Note
It is recommended to use Internet Explorer 8.0 or above to access
the Managed Switch. If the Web interface of the Managed Switch
is not accessible, please turn off the anti-virus software or firewall
andthentryitagain.

6
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to serial (console) port of the Managed Switch. The
console port of the Managed Switch is DCE already, so that you can connect the
consoleportdirectlythroughPCwithouttheneedofNullModem.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 4-1: Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
Switch. Tera Term program may be a good choice. The Tera Term can be accessed
fromtheStart menu.
1. Click STARTmenu,thenPrograms,andthenTera Term.
2.When the following screen appears, make sure that the COM port should be
conguredas:
zBaud:9600
zParity:None
zDatabits:8
zStopbits:1
zFlowcontrol:None
Figure 4-2: Tera Term COM Port Conguration

7
4.1 Logging on to the Console
Once the terminal is connected to the device, power on the Managed Switch, and
theterminalwilldisplay“running testing procedures”.
Then, the following message asks for the login user name and password. The
factory default user name and password are as follows as the login screen in
Figure4-3appears.
Username:admin
Password:admin
Figure 4-3: Managed Switch Console Login Screen
The user can now enter commands to manage the Managed Switch. For a detailed
descriptionofthecommands,pleaserefertothefollowingchapters.
Note
1. For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Accept command in lowercase or uppercase letter under
consoleinterface.

8
4.2 ConguringIPAddress
The IP address conguration commands for VLAN1 interface are listed below.
Before using in-band management, the Managed Switch must be congured with
an IP address by out-of-band management (i.e. console mode). The conguration
commandsareasfollows:
Switch# cong
Switch(cong)# interface vlan 1
Switch(cong-if-Vlan1))# ip address 192.168.1.254 255.255.255.0
ThepreviouscommandwouldapplythefollowingsettingsfortheManagedSwitch.
IPv4Address:192.168.1.254
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the Managed
Switch,pleaseusetheproceduresasfollows:
Show the current IP address
1. On “Switch#”prompt,enter“show ip interface brief”.
2.The screen displays the current IP address, subnet mask and gateway as shown
inFigure4-4.
Figure 4-4: Showing IP Information Screen
If the IP is successfully congured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of Managed Switch
throughthenewIPaddress.
Note
Ifyouarenotfamiliarwithconsolecommandortherelatedparam-
eter,enter“help”anytimeinconsoletogetthehelpdescription.

9
4.3 Setting1000BASE-Xfor10GSFP+Port
The Managed Switch supports both 1000BASE-X and 10GBASE-X SFP
transceivers by manual setting and the default SFP+ port speed is set to 10Gbps.
For example, to establish the ber connection with 1000BASE-X SFP transceiver in
the Ethernet 1/0/1,thefollowingcommandcongurationisrequired:
Switch# cong
Switch(cong)# interface ethernet 1/0/1
Switch(cong-if-ethernet1/0/1)# speed-duplex force1g-full
Switch(cong-if-ethernet1/0/1)# exit
4.4 Changing Password
The default password of the switch is “admin”. For security reason, it is
recommended to change password and the following command conguration is
required:
Switch# cong
Switch(cong)# username admin password planet2018
Switch(cong)#
4.5 SavingtheConguration
In the Managed Switch, the running conguration le stores in the RAM. In the
current version, the running conguration sequence running-cong can be saved
from the RAM to FLASH by write command or copy running-cong startup-
congcommand,sothattherunningcongurationsequencebecomesthestart-up
congurationle,whichiscalledcongurationsave.
Switch# copy running-cong startup-cong
Writerunning-congtocurrentstartup-congsuccessful

10
5. Starting Web Management
The Managed Switch provides a built-in browser interface. You can manage it
remotely by having a remote host with Web browser, such as Microsoft Internet
Explorer,MozillaFirefox,GoogleChromeorAppleSafari.
RJ45/UTP Cable
PC/Workstation with
Web Browser
192.168.1.x
PC/Workstation with
Web Browser
192.168.0.x
Managed Switch
IP Address:
192.168.1.1
Managed Switch
Interface
1/0/1-1/0/24
IP Address:
192.168.0.254
10G Fiber Cable
MGMT
Figure 5-1: IP Management Diagram
The following shows how to start up the Web Management of the Managed
Switch. Please note the Managed Switch is congured through an Ethernet
connection.Please makesurethe managerPCmust beset tothesame IPsubnet
address.
For example, the IP address of the Managed Switch is congured with
192.168.0.254 on Interface VLAN 1 and 192.168.1.1 on Management Port,
then the manager PC should be set to 192.168.0.x or 192.168.1.x (where x is
a number between 2 and 253, except 1 or 254), and the default subnet mask is
255.255.255.0.
Thefactorydefaultusernameandpasswordareasfollows:
DefaultIPofManagementPort:192.168.1.1
DefaultIPofInterfaceVLAN1:192.168.0.254
Username:admin
Password:admin