Planet CV-119/P2000 User manual

L2 Web Smart Gigabit/10Gigabit Ethernet Switch
GS-2240 Series
Quick Installation Guide

Table of Contents
1. Introduction ............................................................................................... 3
2. Package Contents ....................................................................................... 4
3. Requirements ............................................................................................. 5
4. Terminal Setup ........................................................................................... 6
5. Logon to the Console .................................................................................. 7
6. ConguringIPAddressviatheConsole ........................................................ 8
7. SavingtheCongurationviatheConsole.....................................................10
8. Starting Web Management .........................................................................11
9. SavingCongurationviatheWeb ...............................................................14
10.RecoveringBacktoDefaultConguration ....................................................15
11. Customer Support.....................................................................................16

3
1. Introduction
Thank you for purchasing PLANET L2 Web Smart Gigabit/10Gigabit Ethernet
Switch.Thedescriptionofthismodelisshownbelow:
 GS-2240-24T4X24-port10/100/1000T+4-port10GSFP+WebSmartSwitch
 GS-2240-48T4X48-port10/100/1000T+4-port10GSFP+WebSmartSwitch
“Managed Switch” is used as an alternative name in this Quick Installation
Guide.

4
2. Package Contents
Open the box of the Managed Switch and carefully unpack it. The box should
containthefollowingitems:
zThe Managed Switch
zQuickInstallationGuide
zRJ45 to RS232 Cable
zRubberFeet
zTwoRack-mountingBracketswithAttachmentScrews
zPower Cord
zSFPDust-proofCaps
If any item is found missing or damaged, please contact your local reseller for
replacement.

5
3. Requirements
zWorkstations running Windows XP/2003/Vista/7/8/10/2008, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zSerial Port Connection(Terminal)
 TheaboveWorkstationscomewithCOMPort(DB9)orUSB-to-RS232converter.
 The above Workstations have been installed with terminal emulator, such as
HyperTerminalincludedinWindowsXP/2003.
Serial cable -- One end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheManagedSwitch.
zEthernet Port Connection
Network cables--Usestandardnetwork(UTP)cableswithRJ45connectors.
 The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Managed Switch. If the Web interface of the Managed Switch
is not accessible, please turn off the anti-virus software or firewall
and then try it again.

6
4. Terminal Setup
The GS-2240 switch series is equipped with a console interface for local switch
setup and maintenance. To congure the system, connect a serial cable to a COM
port on a PC or notebook computer and to the RJ45 type of the console port of
the Managed Switch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 4-1: Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
Switch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Baud: 115200
Databits: 8
Parity: None
Stopbits: 1
Flowcontrol: None
Figure 4-2: COM Port Conguration

7
5. Logon to the Console
Once the terminal is connected to the device, power on the Managed Switch and
the terminal will display “running testing procedures”. Then, the following message
asks to log-in user name and password. The factory default user name and
passwordareshownasfollows,andtheloginscreeninFigure5-1appears.
Username:admin
Password:admin
Figure 5-1: Managed Switch Console Login Screen
The user can now enter commands to manage the Managed Switch. For a detailed
descriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.Forsecurity reason,pleasechange andmemorize the newpass-
wordafterthisfirstsetup.
2. Only accept command in lowercase letter under console inter-
face.

8
6.ConguringIPAddressviatheConsole
TheManagedSwitchisshippedwithdefaultIPaddressshownbelow:
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the Switch, please
usetheproceduresasfollows:
Show the current IP address
1.Atthe“GS-2240 Series#”prompt,enter“show ip interface vlan1 brief”.
2.The screen displays the current IP address, subnet mask and gateway as shown
inFigure6-1.
Figure 6-1: IP Information Screen

9
 ConguringIPaddress
3.Atthe“GS-2240 Series#”prompt,enter“congure terminal”.
4.At the “GS-2240 Series(cong)#” prompt, enter the following command and
press <Enter>asshowninFigure6-2.
GS-2240Series(cong)# ip route 0.0.0.0/0 192.168.1.254
GS-2240Series(cong)# interface vlan1
GS-2240Series(cong-vlan1)# ip address 192.168.1.100/24
ThepreviouscommandwouldapplythefollowingsettingsfortheSwitch.
IPAddress:192.168.1.100
SubnetMask:255.255.255.0
Gateway:192.168.1.254
Figure 6-2: IP Address Screen
5.RepeatStep1tocheckiftheIPaddressischanged.
If the IP is successfully congured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of the GS-2240
Switch Series through the new IP address.
Note
If you are not familiar with console command or the related
parameter, enter “?” anytime in console to get the help descrip-
tion.

10
7.SavingtheCongurationviatheConsole
In the switch, the running conguration le is stored in the RAM. In the current
version, the running conguration sequence of running-cong can be saved from
the RAM to FLASH by writing the command or copying the running-cong
startup-cong command, so that the running conguration sequence becomes
thestartupcongurationle,whichiscalledcongurationsave.
1.At the “GS-2240 Series#” prompt, enter “copy running-cong startup-
cong” asshowninFigure7-1.
Figure 7-1: The Conguration Screen