Planet FSD-504HP User manual

- 9 -
- 10 - - 12 - - 13 - - 14 -
- 11 -
B. Connect the other end of the cable to the
network devices such as routers, Ethernet
switches or NVRs (network video recorders).
Step 4: Connect your FSD-504HP to PoE PD devices.
A. Connect one end of a standard network
cable to any of the four 10/100Mbps RJ45
PoE+ ports (Port 1 to Port 4).
B. Connect the other end of the cable to the
802.3at/af powered devices.
DC Power Line (DC)
100BASE-TX UTP
PoE
100BASE-TX UTP with PoE
Office Building Office Area
Warehouse
Control Room
Office Building
FSD-504HP
IEEE 802.3af PoE
VoIP Phone
IEEE 802.3at
PoE IP Camera
Fixed IP Dome
IEEE 802.3af PoE Splitter
DC
IEEE 802.3af
PoE IP Camera
PoE Extender
PoE
PoE
PoE
PoE
Wall-mount Installation
Step 1: Please nd the wall that can mount the
FSD-504HP.
Step 2: Please refer to the picture below to screw the
two screws on the wall.
80mm
Step 3: Hang the FSD-504HP on the screws from the
wall.
Step 4: Repeat step 5 of Desktop Installation for
power supply to the FSD-504HP.
Note
Before mounting the device to the wall,
please check the location of the electrical
outlet and the length of the Ethernet cable.
Note
Cable distance for switch
If the “DIP Switch Mode” is set to
“Standard”, then the distance of UTP/
STP cable between the FSD-504HP and
PC/PD devices should not exceed 100
meters.
If the “DIP Switch Mode” is set to
“Extend”, then the cable distance be-
tween the FSD-504HP and PC/PD devices
should not exceed 250 meters.
Note
Make sure the wiring is correct
Category 3/4/5 cable can be used in 10
Mbps operation. To reliably operate your
network at 100Mbps, you must use an un-
shielded twisted-pair (UTP) Category 5/5e
cable, or better data grade cabling. While a
Category 3 or 4 cable may initially seem to
work, it will soon cause data loss.
Step 5: Supply power to the FSD-504HP.
A. Connect one end of the power cable to the
Switch.
B. Connect the power plug of the power cable
to a standard wall outlet.
When the Switch receives power, the power LED should
remain solid Orange.
7. Product Specications
Model
FSD-504HP
4-Port 10/100Mbps 802.3af/at PoE +
1-Port 10/100Mbps Desktop Switch
Hardware Specications
Hardware Version 3
Network Connector 5-Port RJ45 for 10/100BASE-TX, auto
MDI/MDIX
PoE Inject Port 4-Port with 802.3af/at PoE injector
function (Port 1 to port 4)
LED Display
System: Power (Orange)
Per PoE port: PoE (Orange, port 1 to
port 4)
LNK/ACT (Green, port 1 to port 5)
Switch Architecture Store and Forward switch architecture
MAC Address Table 1K MAC address table with auto
learning function
EST Protection 6KV
Switch Fabric 1Gbps
Switch Throughput 0.74Mpps @64bytes
Maximum Packet Size 1536bytes
Flow Control Back pressure for half-duplex. IEEE
802.3x pause frame for full-duplex
Power Requirements DC 51V, 1.25A.
Power Consumption Max. 63 watts, 214 BTU
Dimensions
(W x D x H) 100 x 100 x 26mm
Weight 257g
Power over Ethernet
PoE Standard
IEEE 802.3af Power over Ethernet/PSE
IEEE 802.3at Power over Ethernet Plus/
PSE
PoE Power Supply Type End-span + mid-span
Power Pin Assignment 1/2(+), 4/5(+), 3/6(-), 7/8(-)
PoE Power Output
Per Port 51V DC, 300mA. max. 15.4
watts (IEEE 802.3af)
Per Port 51V DC, 600mA. max. 30
watts (IEEE 802.3at)
PoE Power Budget 60 watts
Number of PDs, 7 watts 4
Number of PDs, 15.4
watts 4
Number of PDs, 30
watts 2
Standard Conformance
EMI Safety FCC, CE
Standard Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
IEEE 802.3af
IEEE 802.3at
Ethernet
Fast Ethernet
Flow Control
Power over Ethernet
Power over Ethernet Plus
Environment
Operating Environment 0 ~ 50 degrees C
Storage Environment -10 ~ 70 degrees C
Operating Humidity 5 ~ 95%, relative humidity, non-
condensing
Storage Humidity 5 ~ 95%, relative humidity, non-
condensing
8. Customer Support
Thank you for purchasing PLANET products. You can
browse our online FAQ resource on PLANET Website
rst to check if it could solve your issue. If you need
more support information, please contact PLANET switch
support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2017.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All
other trademarks belong to their respective owners.

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Check the following contents of your package:
FSD-504HP User’s Manual
51V Power Adapter Foot Pad Power Cord
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
4. LED Indicators
System
LED Color Function
PWR Orange Light: Indicates the Switch has
power.
Per 10/100Mbps Port
LED Color Function
PoE Orange
Lights to indicate the port is
providing 51V DC in-line
power to remote PoE PD.
LNK/ACT Green
Lights to indicate the link through
that port is successfully
established at 10/100Mbps.
Blinks to indicate that the Switch
is actively sending or
receiving data over that
port.
2. Product Features
RJ45 Interface
Five 10/100Mbps Fast Ethernet ports
4 ports support 51V DC power to PoE powered
device
Power over Ethernet
Complies with IEEE 802.3af/at Power over Ethernet
end-span + mid-span PSE
Up to 4 IEEE 802.3af/2 IEEE 802.3at devices
powered
Supports PoE power up to 30 watts for each PoE
port
60-watt PoE budget
Hardware DIP switch for “Standard” and “Extend”
mode selection; the “Extend” mode features
30-watt PoE transmit distance of 250m at speed of
10Mbps and VLAN isolation
Auto detects powered device (PD)
Circuit protection prevents power interference
between ports
Remote power feeding up to 100m with standard
mode
Switching
Hardware based 10/100Mbps auto-negotiation and
auto MDI/MDI-X
Flow control for full duplex operation and back
pressure for half duplex operation
1536bytes packet size support
Integrates address look-up engine, supporting 1K
absolute MAC addresses
Automatic address learning and address aging
Solid DIP switch to isolate ports to prevent
broadcast storm and defend DHCP spoong
Hardware
Desktop palm size
LED indicators for PoE ready/activity and LINK/ACT
6KV lightning protection
One DC 51V power jack
5. Switch Rear Panel
Figure 5-1 shows the rear panel of FSD-504HP.
Standard Extend
51V DC
Figure 5-1: FSD-504HP Rear Panel
The front panel of FSD-504HP provides one DIP switch
for “Standard” and “Extend” mode selections. The
detailed descriptions are shown in the following table.
DIP Switch
Mode Function
Standard
(default)
This mode makes the FSD-504HP operate
as a general switch and all ports operate
at 10/100Mbps auto-negotiation.
Extend
This mode makes the FSD-504HP
operate as a VLAN isolation switch and
port 1 to port 4 will isolate respectively.,
Port 1 to port 4 can only communicate
with port 5 (uplink port).
This mode also makes the FSD-504HP
operate at auto–negotiation 10Mbps
speed duplex mode only, but the delivery
distance of PoE power and network data
can reach 250m.
3. Switch Front Panel
Figure 3-1 shows the front panel of FSD-504HP.
FSD-504HP
PWR
Uplink
PoE 12345
ACTLNK
PoE In-use
Figure 3-1: FSD-504HP Front Panel
Item Interface Description
1Port-1~Port-4
4 10/100BASE-TX RJ45 auto-
MDI/MDI-X ports with 802.af/at
PoE+ injector function.
2Port-5 One 10/100BASE-TX RJ45 auto-
MDI/MDI-X port.
Standard PoE Mode
Power
PoE IP Camera
PoE
10BASE-T UTP with PoE
PoE
100BASE-TX UTP with PoE
PoE
100 meters (328 feet)
FSD-504HP
Extend PoE Mode
Power
PoE
250 meters (820 feet)
FSD-504HP
Standard Extend
Standard Extend
PoE IP Camera
Power
Notice
1. The device is a power-required device,
meaning it will not work till it is pow-
ered. If your networks should be active
all the time, please consider using UPS
(Uninterrupted Power Supply) for your
device. It will prevent you from network
data loss or network downtime.
2. In some area, installing a surge suppres-
sion device may also help to protect your
FSD-504HP from being damaged by un-
regulated surge or current to the FSD-
504HP or the power adapter.
6. Installing the Switch
This part describes how to install your FSD-504HP and
make connections to it. Please read the following topics
and follow the procedures as presented.
Note
This FSD-504HP does not need software
configuration.
Desktop Installation
To install the FSD-504HP on desktop, simply follow the
following steps:
Step 1: Place the FSD-504HP on desktop near AC
power source for its power adapter.
Step 2: Keep enough ventilation space between the
FSD-504HP and the surrounding objects.
Note
When choosing a location, please keep in
mind the environmental restrictions dis-
cussed in Chapter 7 -- Product Specifica-
tions.
Step 3: Connect your FSD-504HP to network devices.
A. Connect one end of a standard network
cable to the Port-5 of the FSD-504HP that
marks with “Uplink”.

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Check the following contents of your package:
FSD-504HP User’s Manual
51V Power Adapter Foot Pad Power Cord
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
4. LED Indicators
System
LED Color Function
PWR Orange Light: Indicates the Switch has
power.
Per 10/100Mbps Port
LED Color Function
PoE Orange
Lights to indicate the port is
providing 51V DC in-line
power to remote PoE PD.
LNK/ACT Green
Lights to indicate the link through
that port is successfully
established at 10/100Mbps.
Blinks to indicate that the Switch
is actively sending or
receiving data over that
port.
2. Product Features
RJ45 Interface
Five 10/100Mbps Fast Ethernet ports
4 ports support 51V DC power to PoE powered
device
Power over Ethernet
Complies with IEEE 802.3af/at Power over Ethernet
end-span + mid-span PSE
Up to 4 IEEE 802.3af/2 IEEE 802.3at devices
powered
Supports PoE power up to 30 watts for each PoE
port
60-watt PoE budget
Hardware DIP switch for “Standard” and “Extend”
mode selection; the “Extend” mode features
30-watt PoE transmit distance of 250m at speed of
10Mbps and VLAN isolation
Auto detects powered device (PD)
Circuit protection prevents power interference
between ports
Remote power feeding up to 100m with standard
mode
Switching
Hardware based 10/100Mbps auto-negotiation and
auto MDI/MDI-X
Flow control for full duplex operation and back
pressure for half duplex operation
1536bytes packet size support
Integrates address look-up engine, supporting 1K
absolute MAC addresses
Automatic address learning and address aging
Solid DIP switch to isolate ports to prevent
broadcast storm and defend DHCP spoong
Hardware
Desktop palm size
LED indicators for PoE ready/activity and LINK/ACT
6KV lightning protection
One DC 51V power jack
5. Switch Rear Panel
Figure 5-1 shows the rear panel of FSD-504HP.
Standard Extend
51V DC
Figure 5-1: FSD-504HP Rear Panel
The front panel of FSD-504HP provides one DIP switch
for “Standard” and “Extend” mode selections. The
detailed descriptions are shown in the following table.
DIP Switch
Mode Function
Standard
(default)
This mode makes the FSD-504HP operate
as a general switch and all ports operate
at 10/100Mbps auto-negotiation.
Extend
This mode makes the FSD-504HP
operate as a VLAN isolation switch and
port 1 to port 4 will isolate respectively.,
Port 1 to port 4 can only communicate
with port 5 (uplink port).
This mode also makes the FSD-504HP
operate at auto–negotiation 10Mbps
speed duplex mode only, but the delivery
distance of PoE power and network data
can reach 250m.
3. Switch Front Panel
Figure 3-1 shows the front panel of FSD-504HP.
FSD-504HP
PWR
Uplink
PoE 12345
ACTLNK
PoE In-use
Figure 3-1: FSD-504HP Front Panel
Item Interface Description
1Port-1~Port-4
4 10/100BASE-TX RJ45 auto-
MDI/MDI-X ports with 802.af/at
PoE+ injector function.
2Port-5 One 10/100BASE-TX RJ45 auto-
MDI/MDI-X port.
Standard PoE Mode
Power
PoE IP Camera
PoE
10BASE-T UTP with PoE
PoE
100BASE-TX UTP with PoE
PoE
100 meters (328 feet)
FSD-504HP
Extend PoE Mode
Power
PoE
250 meters (820 feet)
FSD-504HP
Standard Extend
Standard Extend
PoE IP Camera
Power
Notice
1. The device is a power-required device,
meaning it will not work till it is pow-
ered. If your networks should be active
all the time, please consider using UPS
(Uninterrupted Power Supply) for your
device. It will prevent you from network
data loss or network downtime.
2. In some area, installing a surge suppres-
sion device may also help to protect your
FSD-504HP from being damaged by un-
regulated surge or current to the FSD-
504HP or the power adapter.
6. Installing the Switch
This part describes how to install your FSD-504HP and
make connections to it. Please read the following topics
and follow the procedures as presented.
Note
This FSD-504HP does not need software
configuration.
Desktop Installation
To install the FSD-504HP on desktop, simply follow the
following steps:
Step 1: Place the FSD-504HP on desktop near AC
power source for its power adapter.
Step 2: Keep enough ventilation space between the
FSD-504HP and the surrounding objects.
Note
When choosing a location, please keep in
mind the environmental restrictions dis-
cussed in Chapter 7 -- Product Specifica-
tions.
Step 3: Connect your FSD-504HP to network devices.
A. Connect one end of a standard network
cable to the Port-5 of the FSD-504HP that
marks with “Uplink”.

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Check the following contents of your package:
FSD-504HP User’s Manual
51V Power Adapter Foot Pad Power Cord
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
4. LED Indicators
System
LED Color Function
PWR Orange Light: Indicates the Switch has
power.
Per 10/100Mbps Port
LED Color Function
PoE Orange
Lights to indicate the port is
providing 51V DC in-line
power to remote PoE PD.
LNK/ACT Green
Lights to indicate the link through
that port is successfully
established at 10/100Mbps.
Blinks to indicate that the Switch
is actively sending or
receiving data over that
port.
2. Product Features
RJ45 Interface
Five 10/100Mbps Fast Ethernet ports
4 ports support 51V DC power to PoE powered
device
Power over Ethernet
Complies with IEEE 802.3af/at Power over Ethernet
end-span + mid-span PSE
Up to 4 IEEE 802.3af/2 IEEE 802.3at devices
powered
Supports PoE power up to 30 watts for each PoE
port
60-watt PoE budget
Hardware DIP switch for “Standard” and “Extend”
mode selection; the “Extend” mode features
30-watt PoE transmit distance of 250m at speed of
10Mbps and VLAN isolation
Auto detects powered device (PD)
Circuit protection prevents power interference
between ports
Remote power feeding up to 100m with standard
mode
Switching
Hardware based 10/100Mbps auto-negotiation and
auto MDI/MDI-X
Flow control for full duplex operation and back
pressure for half duplex operation
1536bytes packet size support
Integrates address look-up engine, supporting 1K
absolute MAC addresses
Automatic address learning and address aging
Solid DIP switch to isolate ports to prevent
broadcast storm and defend DHCP spoong
Hardware
Desktop palm size
LED indicators for PoE ready/activity and LINK/ACT
6KV lightning protection
One DC 51V power jack
5. Switch Rear Panel
Figure 5-1 shows the rear panel of FSD-504HP.
Standard Extend
51V DC
Figure 5-1: FSD-504HP Rear Panel
The front panel of FSD-504HP provides one DIP switch
for “Standard” and “Extend” mode selections. The
detailed descriptions are shown in the following table.
DIP Switch
Mode Function
Standard
(default)
This mode makes the FSD-504HP operate
as a general switch and all ports operate
at 10/100Mbps auto-negotiation.
Extend
This mode makes the FSD-504HP
operate as a VLAN isolation switch and
port 1 to port 4 will isolate respectively.,
Port 1 to port 4 can only communicate
with port 5 (uplink port).
This mode also makes the FSD-504HP
operate at auto–negotiation 10Mbps
speed duplex mode only, but the delivery
distance of PoE power and network data
can reach 250m.
3. Switch Front Panel
Figure 3-1 shows the front panel of FSD-504HP.
FSD-504HP
PWR
Uplink
PoE 12345
ACTLNK
PoE In-use
Figure 3-1: FSD-504HP Front Panel
Item Interface Description
1Port-1~Port-4
4 10/100BASE-TX RJ45 auto-
MDI/MDI-X ports with 802.af/at
PoE+ injector function.
2Port-5 One 10/100BASE-TX RJ45 auto-
MDI/MDI-X port.
Standard PoE Mode
Power
PoE IP Camera
PoE
10BASE-T UTP with PoE
PoE
100BASE-TX UTP with PoE
PoE
100 meters (328 feet)
FSD-504HP
Extend PoE Mode
Power
PoE
250 meters (820 feet)
FSD-504HP
Standard Extend
Standard Extend
PoE IP Camera
Power
Notice
1. The device is a power-required device,
meaning it will not work till it is pow-
ered. If your networks should be active
all the time, please consider using UPS
(Uninterrupted Power Supply) for your
device. It will prevent you from network
data loss or network downtime.
2. In some area, installing a surge suppres-
sion device may also help to protect your
FSD-504HP from being damaged by un-
regulated surge or current to the FSD-
504HP or the power adapter.
6. Installing the Switch
This part describes how to install your FSD-504HP and
make connections to it. Please read the following topics
and follow the procedures as presented.
Note
This FSD-504HP does not need software
configuration.
Desktop Installation
To install the FSD-504HP on desktop, simply follow the
following steps:
Step 1: Place the FSD-504HP on desktop near AC
power source for its power adapter.
Step 2: Keep enough ventilation space between the
FSD-504HP and the surrounding objects.
Note
When choosing a location, please keep in
mind the environmental restrictions dis-
cussed in Chapter 7 -- Product Specifica-
tions.
Step 3: Connect your FSD-504HP to network devices.
A. Connect one end of a standard network
cable to the Port-5 of the FSD-504HP that
marks with “Uplink”.

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Check the following contents of your package:
FSD-504HP User’s Manual
51V Power Adapter Foot Pad Power Cord
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
4. LED Indicators
System
LED Color Function
PWR Orange Light: Indicates the Switch has
power.
Per 10/100Mbps Port
LED Color Function
PoE Orange
Lights to indicate the port is
providing 51V DC in-line
power to remote PoE PD.
LNK/ACT Green
Lights to indicate the link through
that port is successfully
established at 10/100Mbps.
Blinks to indicate that the Switch
is actively sending or
receiving data over that
port.
2. Product Features
RJ45 Interface
Five 10/100Mbps Fast Ethernet ports
4 ports support 51V DC power to PoE powered
device
Power over Ethernet
Complies with IEEE 802.3af/at Power over Ethernet
end-span + mid-span PSE
Up to 4 IEEE 802.3af/2 IEEE 802.3at devices
powered
Supports PoE power up to 30 watts for each PoE
port
60-watt PoE budget
Hardware DIP switch for “Standard” and “Extend”
mode selection; the “Extend” mode features
30-watt PoE transmit distance of 250m at speed of
10Mbps and VLAN isolation
Auto detects powered device (PD)
Circuit protection prevents power interference
between ports
Remote power feeding up to 100m with standard
mode
Switching
Hardware based 10/100Mbps auto-negotiation and
auto MDI/MDI-X
Flow control for full duplex operation and back
pressure for half duplex operation
1536bytes packet size support
Integrates address look-up engine, supporting 1K
absolute MAC addresses
Automatic address learning and address aging
Solid DIP switch to isolate ports to prevent
broadcast storm and defend DHCP spoong
Hardware
Desktop palm size
LED indicators for PoE ready/activity and LINK/ACT
6KV lightning protection
One DC 51V power jack
5. Switch Rear Panel
Figure 5-1 shows the rear panel of FSD-504HP.
Standard Extend
51V DC
Figure 5-1: FSD-504HP Rear Panel
The front panel of FSD-504HP provides one DIP switch
for “Standard” and “Extend” mode selections. The
detailed descriptions are shown in the following table.
DIP Switch
Mode Function
Standard
(default)
This mode makes the FSD-504HP operate
as a general switch and all ports operate
at 10/100Mbps auto-negotiation.
Extend
This mode makes the FSD-504HP
operate as a VLAN isolation switch and
port 1 to port 4 will isolate respectively.,
Port 1 to port 4 can only communicate
with port 5 (uplink port).
This mode also makes the FSD-504HP
operate at auto–negotiation 10Mbps
speed duplex mode only, but the delivery
distance of PoE power and network data
can reach 250m.
3. Switch Front Panel
Figure 3-1 shows the front panel of FSD-504HP.
FSD-504HP
PWR
Uplink
PoE 12345
ACTLNK
PoE In-use
Figure 3-1: FSD-504HP Front Panel
Item Interface Description
1Port-1~Port-4
4 10/100BASE-TX RJ45 auto-
MDI/MDI-X ports with 802.af/at
PoE+ injector function.
2Port-5 One 10/100BASE-TX RJ45 auto-
MDI/MDI-X port.
Standard PoE Mode
Power
PoE IP Camera
PoE
10BASE-T UTP with PoE
PoE
100BASE-TX UTP with PoE
PoE
100 meters (328 feet)
FSD-504HP
Extend PoE Mode
Power
PoE
250 meters (820 feet)
FSD-504HP
Standard Extend
Standard Extend
PoE IP Camera
Power
Notice
1. The device is a power-required device,
meaning it will not work till it is pow-
ered. If your networks should be active
all the time, please consider using UPS
(Uninterrupted Power Supply) for your
device. It will prevent you from network
data loss or network downtime.
2. In some area, installing a surge suppres-
sion device may also help to protect your
FSD-504HP from being damaged by un-
regulated surge or current to the FSD-
504HP or the power adapter.
6. Installing the Switch
This part describes how to install your FSD-504HP and
make connections to it. Please read the following topics
and follow the procedures as presented.
Note
This FSD-504HP does not need software
configuration.
Desktop Installation
To install the FSD-504HP on desktop, simply follow the
following steps:
Step 1: Place the FSD-504HP on desktop near AC
power source for its power adapter.
Step 2: Keep enough ventilation space between the
FSD-504HP and the surrounding objects.
Note
When choosing a location, please keep in
mind the environmental restrictions dis-
cussed in Chapter 7 -- Product Specifica-
tions.
Step 3: Connect your FSD-504HP to network devices.
A. Connect one end of a standard network
cable to the Port-5 of the FSD-504HP that
marks with “Uplink”.

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Check the following contents of your package:
FSD-504HP User’s Manual
51V Power Adapter Foot Pad Power Cord
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
4. LED Indicators
System
LED Color Function
PWR Orange Light: Indicates the Switch has
power.
Per 10/100Mbps Port
LED Color Function
PoE Orange
Lights to indicate the port is
providing 51V DC in-line
power to remote PoE PD.
LNK/ACT Green
Lights to indicate the link through
that port is successfully
established at 10/100Mbps.
Blinks to indicate that the Switch
is actively sending or
receiving data over that
port.
2. Product Features
RJ45 Interface
Five 10/100Mbps Fast Ethernet ports
4 ports support 51V DC power to PoE powered
device
Power over Ethernet
Complies with IEEE 802.3af/at Power over Ethernet
end-span + mid-span PSE
Up to 4 IEEE 802.3af/2 IEEE 802.3at devices
powered
Supports PoE power up to 30 watts for each PoE
port
60-watt PoE budget
Hardware DIP switch for “Standard” and “Extend”
mode selection; the “Extend” mode features
30-watt PoE transmit distance of 250m at speed of
10Mbps and VLAN isolation
Auto detects powered device (PD)
Circuit protection prevents power interference
between ports
Remote power feeding up to 100m with standard
mode
Switching
Hardware based 10/100Mbps auto-negotiation and
auto MDI/MDI-X
Flow control for full duplex operation and back
pressure for half duplex operation
1536bytes packet size support
Integrates address look-up engine, supporting 1K
absolute MAC addresses
Automatic address learning and address aging
Solid DIP switch to isolate ports to prevent
broadcast storm and defend DHCP spoong
Hardware
Desktop palm size
LED indicators for PoE ready/activity and LINK/ACT
6KV lightning protection
One DC 51V power jack
5. Switch Rear Panel
Figure 5-1 shows the rear panel of FSD-504HP.
Standard Extend
51V DC
Figure 5-1: FSD-504HP Rear Panel
The front panel of FSD-504HP provides one DIP switch
for “Standard” and “Extend” mode selections. The
detailed descriptions are shown in the following table.
DIP Switch
Mode Function
Standard
(default)
This mode makes the FSD-504HP operate
as a general switch and all ports operate
at 10/100Mbps auto-negotiation.
Extend
This mode makes the FSD-504HP
operate as a VLAN isolation switch and
port 1 to port 4 will isolate respectively.,
Port 1 to port 4 can only communicate
with port 5 (uplink port).
This mode also makes the FSD-504HP
operate at auto–negotiation 10Mbps
speed duplex mode only, but the delivery
distance of PoE power and network data
can reach 250m.
3. Switch Front Panel
Figure 3-1 shows the front panel of FSD-504HP.
FSD-504HP
PWR
Uplink
PoE 12345
ACTLNK
PoE In-use
Figure 3-1: FSD-504HP Front Panel
Item Interface Description
1Port-1~Port-4
4 10/100BASE-TX RJ45 auto-
MDI/MDI-X ports with 802.af/at
PoE+ injector function.
2Port-5 One 10/100BASE-TX RJ45 auto-
MDI/MDI-X port.
Standard PoE Mode
Power
PoE IP Camera
PoE
10BASE-T UTP with PoE
PoE
100BASE-TX UTP with PoE
PoE
100 meters (328 feet)
FSD-504HP
Extend PoE Mode
Power
PoE
250 meters (820 feet)
FSD-504HP
Standard Extend
Standard Extend
PoE IP Camera
Power
Notice
1. The device is a power-required device,
meaning it will not work till it is pow-
ered. If your networks should be active
all the time, please consider using UPS
(Uninterrupted Power Supply) for your
device. It will prevent you from network
data loss or network downtime.
2. In some area, installing a surge suppres-
sion device may also help to protect your
FSD-504HP from being damaged by un-
regulated surge or current to the FSD-
504HP or the power adapter.
6. Installing the Switch
This part describes how to install your FSD-504HP and
make connections to it. Please read the following topics
and follow the procedures as presented.
Note
This FSD-504HP does not need software
configuration.
Desktop Installation
To install the FSD-504HP on desktop, simply follow the
following steps:
Step 1: Place the FSD-504HP on desktop near AC
power source for its power adapter.
Step 2: Keep enough ventilation space between the
FSD-504HP and the surrounding objects.
Note
When choosing a location, please keep in
mind the environmental restrictions dis-
cussed in Chapter 7 -- Product Specifica-
tions.
Step 3: Connect your FSD-504HP to network devices.
A. Connect one end of a standard network
cable to the Port-5 of the FSD-504HP that
marks with “Uplink”.

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Check the following contents of your package:
FSD-504HP User’s Manual
51V Power Adapter Foot Pad Power Cord
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
4. LED Indicators
System
LED Color Function
PWR Orange Light: Indicates the Switch has
power.
Per 10/100Mbps Port
LED Color Function
PoE Orange
Lights to indicate the port is
providing 51V DC in-line
power to remote PoE PD.
LNK/ACT Green
Lights to indicate the link through
that port is successfully
established at 10/100Mbps.
Blinks to indicate that the Switch
is actively sending or
receiving data over that
port.
2. Product Features
RJ45 Interface
Five 10/100Mbps Fast Ethernet ports
4 ports support 51V DC power to PoE powered
device
Power over Ethernet
Complies with IEEE 802.3af/at Power over Ethernet
end-span + mid-span PSE
Up to 4 IEEE 802.3af/2 IEEE 802.3at devices
powered
Supports PoE power up to 30 watts for each PoE
port
60-watt PoE budget
Hardware DIP switch for “Standard” and “Extend”
mode selection; the “Extend” mode features
30-watt PoE transmit distance of 250m at speed of
10Mbps and VLAN isolation
Auto detects powered device (PD)
Circuit protection prevents power interference
between ports
Remote power feeding up to 100m with standard
mode
Switching
Hardware based 10/100Mbps auto-negotiation and
auto MDI/MDI-X
Flow control for full duplex operation and back
pressure for half duplex operation
1536bytes packet size support
Integrates address look-up engine, supporting 1K
absolute MAC addresses
Automatic address learning and address aging
Solid DIP switch to isolate ports to prevent
broadcast storm and defend DHCP spoong
Hardware
Desktop palm size
LED indicators for PoE ready/activity and LINK/ACT
6KV lightning protection
One DC 51V power jack
5. Switch Rear Panel
Figure 5-1 shows the rear panel of FSD-504HP.
Standard Extend
51V DC
Figure 5-1: FSD-504HP Rear Panel
The front panel of FSD-504HP provides one DIP switch
for “Standard” and “Extend” mode selections. The
detailed descriptions are shown in the following table.
DIP Switch
Mode Function
Standard
(default)
This mode makes the FSD-504HP operate
as a general switch and all ports operate
at 10/100Mbps auto-negotiation.
Extend
This mode makes the FSD-504HP
operate as a VLAN isolation switch and
port 1 to port 4 will isolate respectively.,
Port 1 to port 4 can only communicate
with port 5 (uplink port).
This mode also makes the FSD-504HP
operate at auto–negotiation 10Mbps
speed duplex mode only, but the delivery
distance of PoE power and network data
can reach 250m.
3. Switch Front Panel
Figure 3-1 shows the front panel of FSD-504HP.
FSD-504HP
PWR
Uplink
PoE 12345
ACTLNK
PoE In-use
Figure 3-1: FSD-504HP Front Panel
Item Interface Description
1Port-1~Port-4
4 10/100BASE-TX RJ45 auto-
MDI/MDI-X ports with 802.af/at
PoE+ injector function.
2Port-5 One 10/100BASE-TX RJ45 auto-
MDI/MDI-X port.
Standard PoE Mode
Power
PoE IP Camera
PoE
10BASE-T UTP with PoE
PoE
100BASE-TX UTP with PoE
PoE
100 meters (328 feet)
FSD-504HP
Extend PoE Mode
Power
PoE
250 meters (820 feet)
FSD-504HP
Standard Extend
Standard Extend
PoE IP Camera
Power
Notice
1. The device is a power-required device,
meaning it will not work till it is pow-
ered. If your networks should be active
all the time, please consider using UPS
(Uninterrupted Power Supply) for your
device. It will prevent you from network
data loss or network downtime.
2. In some area, installing a surge suppres-
sion device may also help to protect your
FSD-504HP from being damaged by un-
regulated surge or current to the FSD-
504HP or the power adapter.
6. Installing the Switch
This part describes how to install your FSD-504HP and
make connections to it. Please read the following topics
and follow the procedures as presented.
Note
This FSD-504HP does not need software
configuration.
Desktop Installation
To install the FSD-504HP on desktop, simply follow the
following steps:
Step 1: Place the FSD-504HP on desktop near AC
power source for its power adapter.
Step 2: Keep enough ventilation space between the
FSD-504HP and the surrounding objects.
Note
When choosing a location, please keep in
mind the environmental restrictions dis-
cussed in Chapter 7 -- Product Specifica-
tions.
Step 3: Connect your FSD-504HP to network devices.
A. Connect one end of a standard network
cable to the Port-5 of the FSD-504HP that
marks with “Uplink”.

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Check the following contents of your package:
FSD-504HP User’s Manual
51V Power Adapter Foot Pad Power Cord
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
4. LED Indicators
System
LED Color Function
PWR Orange Light: Indicates the Switch has
power.
Per 10/100Mbps Port
LED Color Function
PoE Orange
Lights to indicate the port is
providing 51V DC in-line
power to remote PoE PD.
LNK/ACT Green
Lights to indicate the link through
that port is successfully
established at 10/100Mbps.
Blinks to indicate that the Switch
is actively sending or
receiving data over that
port.
2. Product Features
RJ45 Interface
Five 10/100Mbps Fast Ethernet ports
4 ports support 51V DC power to PoE powered
device
Power over Ethernet
Complies with IEEE 802.3af/at Power over Ethernet
end-span + mid-span PSE
Up to 4 IEEE 802.3af/2 IEEE 802.3at devices
powered
Supports PoE power up to 30 watts for each PoE
port
60-watt PoE budget
Hardware DIP switch for “Standard” and “Extend”
mode selection; the “Extend” mode features
30-watt PoE transmit distance of 250m at speed of
10Mbps and VLAN isolation
Auto detects powered device (PD)
Circuit protection prevents power interference
between ports
Remote power feeding up to 100m with standard
mode
Switching
Hardware based 10/100Mbps auto-negotiation and
auto MDI/MDI-X
Flow control for full duplex operation and back
pressure for half duplex operation
1536bytes packet size support
Integrates address look-up engine, supporting 1K
absolute MAC addresses
Automatic address learning and address aging
Solid DIP switch to isolate ports to prevent
broadcast storm and defend DHCP spoong
Hardware
Desktop palm size
LED indicators for PoE ready/activity and LINK/ACT
6KV lightning protection
One DC 51V power jack
5. Switch Rear Panel
Figure 5-1 shows the rear panel of FSD-504HP.
Standard Extend
51V DC
Figure 5-1: FSD-504HP Rear Panel
The front panel of FSD-504HP provides one DIP switch
for “Standard” and “Extend” mode selections. The
detailed descriptions are shown in the following table.
DIP Switch
Mode Function
Standard
(default)
This mode makes the FSD-504HP operate
as a general switch and all ports operate
at 10/100Mbps auto-negotiation.
Extend
This mode makes the FSD-504HP
operate as a VLAN isolation switch and
port 1 to port 4 will isolate respectively.,
Port 1 to port 4 can only communicate
with port 5 (uplink port).
This mode also makes the FSD-504HP
operate at auto–negotiation 10Mbps
speed duplex mode only, but the delivery
distance of PoE power and network data
can reach 250m.
3. Switch Front Panel
Figure 3-1 shows the front panel of FSD-504HP.
FSD-504HP
PWR
Uplink
PoE 12345
ACTLNK
PoE In-use
Figure 3-1: FSD-504HP Front Panel
Item Interface Description
1Port-1~Port-4
4 10/100BASE-TX RJ45 auto-
MDI/MDI-X ports with 802.af/at
PoE+ injector function.
2Port-5 One 10/100BASE-TX RJ45 auto-
MDI/MDI-X port.
Standard PoE Mode
Power
PoE IP Camera
PoE
10BASE-T UTP with PoE
PoE
100BASE-TX UTP with PoE
PoE
100 meters (328 feet)
FSD-504HP
Extend PoE Mode
Power
PoE
250 meters (820 feet)
FSD-504HP
Standard Extend
Standard Extend
PoE IP Camera
Power
Notice
1. The device is a power-required device,
meaning it will not work till it is pow-
ered. If your networks should be active
all the time, please consider using UPS
(Uninterrupted Power Supply) for your
device. It will prevent you from network
data loss or network downtime.
2. In some area, installing a surge suppres-
sion device may also help to protect your
FSD-504HP from being damaged by un-
regulated surge or current to the FSD-
504HP or the power adapter.
6. Installing the Switch
This part describes how to install your FSD-504HP and
make connections to it. Please read the following topics
and follow the procedures as presented.
Note
This FSD-504HP does not need software
configuration.
Desktop Installation
To install the FSD-504HP on desktop, simply follow the
following steps:
Step 1: Place the FSD-504HP on desktop near AC
power source for its power adapter.
Step 2: Keep enough ventilation space between the
FSD-504HP and the surrounding objects.
Note
When choosing a location, please keep in
mind the environmental restrictions dis-
cussed in Chapter 7 -- Product Specifica-
tions.
Step 3: Connect your FSD-504HP to network devices.
A. Connect one end of a standard network
cable to the Port-5 of the FSD-504HP that
marks with “Uplink”.

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Check the following contents of your package:
FSD-504HP User’s Manual
51V Power Adapter Foot Pad Power Cord
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
4. LED Indicators
System
LED Color Function
PWR Orange Light: Indicates the Switch has
power.
Per 10/100Mbps Port
LED Color Function
PoE Orange
Lights to indicate the port is
providing 51V DC in-line
power to remote PoE PD.
LNK/ACT Green
Lights to indicate the link through
that port is successfully
established at 10/100Mbps.
Blinks to indicate that the Switch
is actively sending or
receiving data over that
port.
2. Product Features
RJ45 Interface
Five 10/100Mbps Fast Ethernet ports
4 ports support 51V DC power to PoE powered
device
Power over Ethernet
Complies with IEEE 802.3af/at Power over Ethernet
end-span + mid-span PSE
Up to 4 IEEE 802.3af/2 IEEE 802.3at devices
powered
Supports PoE power up to 30 watts for each PoE
port
60-watt PoE budget
Hardware DIP switch for “Standard” and “Extend”
mode selection; the “Extend” mode features
30-watt PoE transmit distance of 250m at speed of
10Mbps and VLAN isolation
Auto detects powered device (PD)
Circuit protection prevents power interference
between ports
Remote power feeding up to 100m with standard
mode
Switching
Hardware based 10/100Mbps auto-negotiation and
auto MDI/MDI-X
Flow control for full duplex operation and back
pressure for half duplex operation
1536bytes packet size support
Integrates address look-up engine, supporting 1K
absolute MAC addresses
Automatic address learning and address aging
Solid DIP switch to isolate ports to prevent
broadcast storm and defend DHCP spoong
Hardware
Desktop palm size
LED indicators for PoE ready/activity and LINK/ACT
6KV lightning protection
One DC 51V power jack
5. Switch Rear Panel
Figure 5-1 shows the rear panel of FSD-504HP.
Standard Extend
51V DC
Figure 5-1: FSD-504HP Rear Panel
The front panel of FSD-504HP provides one DIP switch
for “Standard” and “Extend” mode selections. The
detailed descriptions are shown in the following table.
DIP Switch
Mode Function
Standard
(default)
This mode makes the FSD-504HP operate
as a general switch and all ports operate
at 10/100Mbps auto-negotiation.
Extend
This mode makes the FSD-504HP
operate as a VLAN isolation switch and
port 1 to port 4 will isolate respectively.,
Port 1 to port 4 can only communicate
with port 5 (uplink port).
This mode also makes the FSD-504HP
operate at auto–negotiation 10Mbps
speed duplex mode only, but the delivery
distance of PoE power and network data
can reach 250m.
3. Switch Front Panel
Figure 3-1 shows the front panel of FSD-504HP.
FSD-504HP
PWR
Uplink
PoE 12345
ACTLNK
PoE In-use
Figure 3-1: FSD-504HP Front Panel
Item Interface Description
1Port-1~Port-4
4 10/100BASE-TX RJ45 auto-
MDI/MDI-X ports with 802.af/at
PoE+ injector function.
2Port-5 One 10/100BASE-TX RJ45 auto-
MDI/MDI-X port.
Standard PoE Mode
Power
PoE IP Camera
PoE
10BASE-T UTP with PoE
PoE
100BASE-TX UTP with PoE
PoE
100 meters (328 feet)
FSD-504HP
Extend PoE Mode
Power
PoE
250 meters (820 feet)
FSD-504HP
Standard Extend
Standard Extend
PoE IP Camera
Power
Notice
1. The device is a power-required device,
meaning it will not work till it is pow-
ered. If your networks should be active
all the time, please consider using UPS
(Uninterrupted Power Supply) for your
device. It will prevent you from network
data loss or network downtime.
2. In some area, installing a surge suppres-
sion device may also help to protect your
FSD-504HP from being damaged by un-
regulated surge or current to the FSD-
504HP or the power adapter.
6. Installing the Switch
This part describes how to install your FSD-504HP and
make connections to it. Please read the following topics
and follow the procedures as presented.
Note
This FSD-504HP does not need software
configuration.
Desktop Installation
To install the FSD-504HP on desktop, simply follow the
following steps:
Step 1: Place the FSD-504HP on desktop near AC
power source for its power adapter.
Step 2: Keep enough ventilation space between the
FSD-504HP and the surrounding objects.
Note
When choosing a location, please keep in
mind the environmental restrictions dis-
cussed in Chapter 7 -- Product Specifica-
tions.
Step 3: Connect your FSD-504HP to network devices.
A. Connect one end of a standard network
cable to the Port-5 of the FSD-504HP that
marks with “Uplink”.

- 9 -
- 10 - - 12 - - 13 - - 14 -
- 11 -
B. Connect the other end of the cable to the
network devices such as routers, Ethernet
switches or NVRs (network video recorders).
Step 4: Connect your FSD-504HP to PoE PD devices.
A. Connect one end of a standard network
cable to any of the four 10/100Mbps RJ45
PoE+ ports (Port 1 to Port 4).
B. Connect the other end of the cable to the
802.3at/af powered devices.
DC Power Line (DC)
100BASE-TX UTP
PoE
100BASE-TX UTP with PoE
Office Building Office Area
Warehouse
Control Room
Office Building
FSD-504HP
IEEE 802.3af PoE
VoIP Phone
IEEE 802.3at
PoE IP Camera
Fixed IP Dome
IEEE 802.3af PoE Splitter
DC
IEEE 802.3af
PoE IP Camera
PoE Extender
PoE
PoE
PoE
PoE
Wall-mount Installation
Step 1: Please nd the wall that can mount the
FSD-504HP.
Step 2: Please refer to the picture below to screw the
two screws on the wall.
80mm
Step 3: Hang the FSD-504HP on the screws from the
wall.
Step 4: Repeat step 5 of Desktop Installation for
power supply to the FSD-504HP.
Note
Before mounting the device to the wall,
please check the location of the electrical
outlet and the length of the Ethernet cable.
Note
Cable distance for switch
If the “DIP Switch Mode” is set to
“Standard”, then the distance of UTP/
STP cable between the FSD-504HP and
PC/PD devices should not exceed 100
meters.
If the “DIP Switch Mode” is set to
“Extend”, then the cable distance be-
tween the FSD-504HP and PC/PD devices
should not exceed 250 meters.
Note
Make sure the wiring is correct
Category 3/4/5 cable can be used in 10
Mbps operation. To reliably operate your
network at 100Mbps, you must use an un-
shielded twisted-pair (UTP) Category 5/5e
cable, or better data grade cabling. While a
Category 3 or 4 cable may initially seem to
work, it will soon cause data loss.
Step 5: Supply power to the FSD-504HP.
A. Connect one end of the power cable to the
Switch.
B. Connect the power plug of the power cable
to a standard wall outlet.
When the Switch receives power, the power LED should
remain solid Orange.
7. Product Specications
Model
FSD-504HP
4-Port 10/100Mbps 802.3af/at PoE +
1-Port 10/100Mbps Desktop Switch
Hardware Specications
Hardware Version 3
Network Connector 5-Port RJ45 for 10/100BASE-TX, auto
MDI/MDIX
PoE Inject Port 4-Port with 802.3af/at PoE injector
function (Port 1 to port 4)
LED Display
System: Power (Orange)
Per PoE port: PoE (Orange, port 1 to
port 4)
LNK/ACT (Green, port 1 to port 5)
Switch Architecture Store and Forward switch architecture
MAC Address Table 1K MAC address table with auto
learning function
EST Protection 6KV
Switch Fabric 1Gbps
Switch Throughput 0.74Mpps @64bytes
Maximum Packet Size 1536bytes
Flow Control Back pressure for half-duplex. IEEE
802.3x pause frame for full-duplex
Power Requirements DC 51V, 1.25A.
Power Consumption Max. 63 watts, 214 BTU
Dimensions
(W x D x H) 100 x 100 x 26mm
Weight 257g
Power over Ethernet
PoE Standard
IEEE 802.3af Power over Ethernet/PSE
IEEE 802.3at Power over Ethernet Plus/
PSE
PoE Power Supply Type End-span + mid-span
Power Pin Assignment 1/2(+), 4/5(+), 3/6(-), 7/8(-)
PoE Power Output
Per Port 51V DC, 300mA. max. 15.4
watts (IEEE 802.3af)
Per Port 51V DC, 600mA. max. 30
watts (IEEE 802.3at)
PoE Power Budget 60 watts
Number of PDs, 7 watts 4
Number of PDs, 15.4
watts 4
Number of PDs, 30
watts 2
Standard Conformance
EMI Safety FCC, CE
Standard Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
IEEE 802.3af
IEEE 802.3at
Ethernet
Fast Ethernet
Flow Control
Power over Ethernet
Power over Ethernet Plus
Environment
Operating Environment 0 ~ 50 degrees C
Storage Environment -10 ~ 70 degrees C
Operating Humidity 5 ~ 95%, relative humidity, non-
condensing
Storage Humidity 5 ~ 95%, relative humidity, non-
condensing
8. Customer Support
Thank you for purchasing PLANET products. You can
browse our online FAQ resource on PLANET Website
rst to check if it could solve your issue. If you need
more support information, please contact PLANET switch
support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2017.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All
other trademarks belong to their respective owners.

- 9 -
- 10 - - 12 - - 13 - - 14 -
- 11 -
B. Connect the other end of the cable to the
network devices such as routers, Ethernet
switches or NVRs (network video recorders).
Step 4: Connect your FSD-504HP to PoE PD devices.
A. Connect one end of a standard network
cable to any of the four 10/100Mbps RJ45
PoE+ ports (Port 1 to Port 4).
B. Connect the other end of the cable to the
802.3at/af powered devices.
DC Power Line (DC)
100BASE-TX UTP
PoE
100BASE-TX UTP with PoE
Office Building Office Area
Warehouse
Control Room
Office Building
FSD-504HP
IEEE 802.3af PoE
VoIP Phone
IEEE 802.3at
PoE IP Camera
Fixed IP Dome
IEEE 802.3af PoE Splitter
DC
IEEE 802.3af
PoE IP Camera
PoE Extender
PoE
PoE
PoE
PoE
Wall-mount Installation
Step 1: Please nd the wall that can mount the
FSD-504HP.
Step 2: Please refer to the picture below to screw the
two screws on the wall.
80mm
Step 3: Hang the FSD-504HP on the screws from the
wall.
Step 4: Repeat step 5 of Desktop Installation for
power supply to the FSD-504HP.
Note
Before mounting the device to the wall,
please check the location of the electrical
outlet and the length of the Ethernet cable.
Note
Cable distance for switch
If the “DIP Switch Mode” is set to
“Standard”, then the distance of UTP/
STP cable between the FSD-504HP and
PC/PD devices should not exceed 100
meters.
If the “DIP Switch Mode” is set to
“Extend”, then the cable distance be-
tween the FSD-504HP and PC/PD devices
should not exceed 250 meters.
Note
Make sure the wiring is correct
Category 3/4/5 cable can be used in 10
Mbps operation. To reliably operate your
network at 100Mbps, you must use an un-
shielded twisted-pair (UTP) Category 5/5e
cable, or better data grade cabling. While a
Category 3 or 4 cable may initially seem to
work, it will soon cause data loss.
Step 5: Supply power to the FSD-504HP.
A. Connect one end of the power cable to the
Switch.
B. Connect the power plug of the power cable
to a standard wall outlet.
When the Switch receives power, the power LED should
remain solid Orange.
7. Product Specications
Model
FSD-504HP
4-Port 10/100Mbps 802.3af/at PoE +
1-Port 10/100Mbps Desktop Switch
Hardware Specications
Hardware Version 3
Network Connector 5-Port RJ45 for 10/100BASE-TX, auto
MDI/MDIX
PoE Inject Port 4-Port with 802.3af/at PoE injector
function (Port 1 to port 4)
LED Display
System: Power (Orange)
Per PoE port: PoE (Orange, port 1 to
port 4)
LNK/ACT (Green, port 1 to port 5)
Switch Architecture Store and Forward switch architecture
MAC Address Table 1K MAC address table with auto
learning function
EST Protection 6KV
Switch Fabric 1Gbps
Switch Throughput 0.74Mpps @64bytes
Maximum Packet Size 1536bytes
Flow Control Back pressure for half-duplex. IEEE
802.3x pause frame for full-duplex
Power Requirements DC 51V, 1.25A.
Power Consumption Max. 63 watts, 214 BTU
Dimensions
(W x D x H) 100 x 100 x 26mm
Weight 257g
Power over Ethernet
PoE Standard
IEEE 802.3af Power over Ethernet/PSE
IEEE 802.3at Power over Ethernet Plus/
PSE
PoE Power Supply Type End-span + mid-span
Power Pin Assignment 1/2(+), 4/5(+), 3/6(-), 7/8(-)
PoE Power Output
Per Port 51V DC, 300mA. max. 15.4
watts (IEEE 802.3af)
Per Port 51V DC, 600mA. max. 30
watts (IEEE 802.3at)
PoE Power Budget 60 watts
Number of PDs, 7 watts 4
Number of PDs, 15.4
watts 4
Number of PDs, 30
watts 2
Standard Conformance
EMI Safety FCC, CE
Standard Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
IEEE 802.3af
IEEE 802.3at
Ethernet
Fast Ethernet
Flow Control
Power over Ethernet
Power over Ethernet Plus
Environment
Operating Environment 0 ~ 50 degrees C
Storage Environment -10 ~ 70 degrees C
Operating Humidity 5 ~ 95%, relative humidity, non-
condensing
Storage Humidity 5 ~ 95%, relative humidity, non-
condensing
8. Customer Support
Thank you for purchasing PLANET products. You can
browse our online FAQ resource on PLANET Website
rst to check if it could solve your issue. If you need
more support information, please contact PLANET switch
support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2017.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All
other trademarks belong to their respective owners.

- 9 -
- 10 - - 12 - - 13 - - 14 -
- 11 -
B. Connect the other end of the cable to the
network devices such as routers, Ethernet
switches or NVRs (network video recorders).
Step 4: Connect your FSD-504HP to PoE PD devices.
A. Connect one end of a standard network
cable to any of the four 10/100Mbps RJ45
PoE+ ports (Port 1 to Port 4).
B. Connect the other end of the cable to the
802.3at/af powered devices.
DC Power Line (DC)
100BASE-TX UTP
PoE
100BASE-TX UTP with PoE
Office Building Office Area
Warehouse
Control Room
Office Building
FSD-504HP
IEEE 802.3af PoE
VoIP Phone
IEEE 802.3at
PoE IP Camera
Fixed IP Dome
IEEE 802.3af PoE Splitter
DC
IEEE 802.3af
PoE IP Camera
PoE Extender
PoE
PoE
PoE
PoE
Wall-mount Installation
Step 1: Please nd the wall that can mount the
FSD-504HP.
Step 2: Please refer to the picture below to screw the
two screws on the wall.
80mm
Step 3: Hang the FSD-504HP on the screws from the
wall.
Step 4: Repeat step 5 of Desktop Installation for
power supply to the FSD-504HP.
Note
Before mounting the device to the wall,
please check the location of the electrical
outlet and the length of the Ethernet cable.
Note
Cable distance for switch
If the “DIP Switch Mode” is set to
“Standard”, then the distance of UTP/
STP cable between the FSD-504HP and
PC/PD devices should not exceed 100
meters.
If the “DIP Switch Mode” is set to
“Extend”, then the cable distance be-
tween the FSD-504HP and PC/PD devices
should not exceed 250 meters.
Note
Make sure the wiring is correct
Category 3/4/5 cable can be used in 10
Mbps operation. To reliably operate your
network at 100Mbps, you must use an un-
shielded twisted-pair (UTP) Category 5/5e
cable, or better data grade cabling. While a
Category 3 or 4 cable may initially seem to
work, it will soon cause data loss.
Step 5: Supply power to the FSD-504HP.
A. Connect one end of the power cable to the
Switch.
B. Connect the power plug of the power cable
to a standard wall outlet.
When the Switch receives power, the power LED should
remain solid Orange.
7. Product Specications
Model
FSD-504HP
4-Port 10/100Mbps 802.3af/at PoE +
1-Port 10/100Mbps Desktop Switch
Hardware Specications
Hardware Version 3
Network Connector 5-Port RJ45 for 10/100BASE-TX, auto
MDI/MDIX
PoE Inject Port 4-Port with 802.3af/at PoE injector
function (Port 1 to port 4)
LED Display
System: Power (Orange)
Per PoE port: PoE (Orange, port 1 to
port 4)
LNK/ACT (Green, port 1 to port 5)
Switch Architecture Store and Forward switch architecture
MAC Address Table 1K MAC address table with auto
learning function
EST Protection 6KV
Switch Fabric 1Gbps
Switch Throughput 0.74Mpps @64bytes
Maximum Packet Size 1536bytes
Flow Control Back pressure for half-duplex. IEEE
802.3x pause frame for full-duplex
Power Requirements DC 51V, 1.25A.
Power Consumption Max. 63 watts, 214 BTU
Dimensions
(W x D x H) 100 x 100 x 26mm
Weight 257g
Power over Ethernet
PoE Standard
IEEE 802.3af Power over Ethernet/PSE
IEEE 802.3at Power over Ethernet Plus/
PSE
PoE Power Supply Type End-span + mid-span
Power Pin Assignment 1/2(+), 4/5(+), 3/6(-), 7/8(-)
PoE Power Output
Per Port 51V DC, 300mA. max. 15.4
watts (IEEE 802.3af)
Per Port 51V DC, 600mA. max. 30
watts (IEEE 802.3at)
PoE Power Budget 60 watts
Number of PDs, 7 watts 4
Number of PDs, 15.4
watts 4
Number of PDs, 30
watts 2
Standard Conformance
EMI Safety FCC, CE
Standard Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
IEEE 802.3af
IEEE 802.3at
Ethernet
Fast Ethernet
Flow Control
Power over Ethernet
Power over Ethernet Plus
Environment
Operating Environment 0 ~ 50 degrees C
Storage Environment -10 ~ 70 degrees C
Operating Humidity 5 ~ 95%, relative humidity, non-
condensing
Storage Humidity 5 ~ 95%, relative humidity, non-
condensing
8. Customer Support
Thank you for purchasing PLANET products. You can
browse our online FAQ resource on PLANET Website
rst to check if it could solve your issue. If you need
more support information, please contact PLANET switch
support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2017.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All
other trademarks belong to their respective owners.

- 9 -
- 10 - - 12 - - 13 - - 14 -
- 11 -
B. Connect the other end of the cable to the
network devices such as routers, Ethernet
switches or NVRs (network video recorders).
Step 4: Connect your FSD-504HP to PoE PD devices.
A. Connect one end of a standard network
cable to any of the four 10/100Mbps RJ45
PoE+ ports (Port 1 to Port 4).
B. Connect the other end of the cable to the
802.3at/af powered devices.
DC Power Line (DC)
100BASE-TX UTP
PoE
100BASE-TX UTP with PoE
Office Building Office Area
Warehouse
Control Room
Office Building
FSD-504HP
IEEE 802.3af PoE
VoIP Phone
IEEE 802.3at
PoE IP Camera
Fixed IP Dome
IEEE 802.3af PoE Splitter
DC
IEEE 802.3af
PoE IP Camera
PoE Extender
PoE
PoE
PoE
PoE
Wall-mount Installation
Step 1: Please nd the wall that can mount the
FSD-504HP.
Step 2: Please refer to the picture below to screw the
two screws on the wall.
80mm
Step 3: Hang the FSD-504HP on the screws from the
wall.
Step 4: Repeat step 5 of Desktop Installation for
power supply to the FSD-504HP.
Note
Before mounting the device to the wall,
please check the location of the electrical
outlet and the length of the Ethernet cable.
Note
Cable distance for switch
If the “DIP Switch Mode” is set to
“Standard”, then the distance of UTP/
STP cable between the FSD-504HP and
PC/PD devices should not exceed 100
meters.
If the “DIP Switch Mode” is set to
“Extend”, then the cable distance be-
tween the FSD-504HP and PC/PD devices
should not exceed 250 meters.
Note
Make sure the wiring is correct
Category 3/4/5 cable can be used in 10
Mbps operation. To reliably operate your
network at 100Mbps, you must use an un-
shielded twisted-pair (UTP) Category 5/5e
cable, or better data grade cabling. While a
Category 3 or 4 cable may initially seem to
work, it will soon cause data loss.
Step 5: Supply power to the FSD-504HP.
A. Connect one end of the power cable to the
Switch.
B. Connect the power plug of the power cable
to a standard wall outlet.
When the Switch receives power, the power LED should
remain solid Orange.
7. Product Specications
Model
FSD-504HP
4-Port 10/100Mbps 802.3af/at PoE +
1-Port 10/100Mbps Desktop Switch
Hardware Specications
Hardware Version 3
Network Connector 5-Port RJ45 for 10/100BASE-TX, auto
MDI/MDIX
PoE Inject Port 4-Port with 802.3af/at PoE injector
function (Port 1 to port 4)
LED Display
System: Power (Orange)
Per PoE port: PoE (Orange, port 1 to
port 4)
LNK/ACT (Green, port 1 to port 5)
Switch Architecture Store and Forward switch architecture
MAC Address Table 1K MAC address table with auto
learning function
EST Protection 6KV
Switch Fabric 1Gbps
Switch Throughput 0.74Mpps @64bytes
Maximum Packet Size 1536bytes
Flow Control Back pressure for half-duplex. IEEE
802.3x pause frame for full-duplex
Power Requirements DC 51V, 1.25A.
Power Consumption Max. 63 watts, 214 BTU
Dimensions
(W x D x H) 100 x 100 x 26mm
Weight 257g
Power over Ethernet
PoE Standard
IEEE 802.3af Power over Ethernet/PSE
IEEE 802.3at Power over Ethernet Plus/
PSE
PoE Power Supply Type End-span + mid-span
Power Pin Assignment 1/2(+), 4/5(+), 3/6(-), 7/8(-)
PoE Power Output
Per Port 51V DC, 300mA. max. 15.4
watts (IEEE 802.3af)
Per Port 51V DC, 600mA. max. 30
watts (IEEE 802.3at)
PoE Power Budget 60 watts
Number of PDs, 7 watts 4
Number of PDs, 15.4
watts 4
Number of PDs, 30
watts 2
Standard Conformance
EMI Safety FCC, CE
Standard Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
IEEE 802.3af
IEEE 802.3at
Ethernet
Fast Ethernet
Flow Control
Power over Ethernet
Power over Ethernet Plus
Environment
Operating Environment 0 ~ 50 degrees C
Storage Environment -10 ~ 70 degrees C
Operating Humidity 5 ~ 95%, relative humidity, non-
condensing
Storage Humidity 5 ~ 95%, relative humidity, non-
condensing
8. Customer Support
Thank you for purchasing PLANET products. You can
browse our online FAQ resource on PLANET Website
rst to check if it could solve your issue. If you need
more support information, please contact PLANET switch
support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2017.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All
other trademarks belong to their respective owners.

- 9 -
- 10 - - 12 - - 13 - - 14 -
- 11 -
B. Connect the other end of the cable to the
network devices such as routers, Ethernet
switches or NVRs (network video recorders).
Step 4: Connect your FSD-504HP to PoE PD devices.
A. Connect one end of a standard network
cable to any of the four 10/100Mbps RJ45
PoE+ ports (Port 1 to Port 4).
B. Connect the other end of the cable to the
802.3at/af powered devices.
DC Power Line (DC)
100BASE-TX UTP
PoE
100BASE-TX UTP with PoE
Office Building Office Area
Warehouse
Control Room
Office Building
FSD-504HP
IEEE 802.3af PoE
VoIP Phone
IEEE 802.3at
PoE IP Camera
Fixed IP Dome
IEEE 802.3af PoE Splitter
DC
IEEE 802.3af
PoE IP Camera
PoE Extender
PoE
PoE
PoE
PoE
Wall-mount Installation
Step 1: Please nd the wall that can mount the
FSD-504HP.
Step 2: Please refer to the picture below to screw the
two screws on the wall.
80mm
Step 3: Hang the FSD-504HP on the screws from the
wall.
Step 4: Repeat step 5 of Desktop Installation for
power supply to the FSD-504HP.
Note
Before mounting the device to the wall,
please check the location of the electrical
outlet and the length of the Ethernet cable.
Note
Cable distance for switch
If the “DIP Switch Mode” is set to
“Standard”, then the distance of UTP/
STP cable between the FSD-504HP and
PC/PD devices should not exceed 100
meters.
If the “DIP Switch Mode” is set to
“Extend”, then the cable distance be-
tween the FSD-504HP and PC/PD devices
should not exceed 250 meters.
Note
Make sure the wiring is correct
Category 3/4/5 cable can be used in 10
Mbps operation. To reliably operate your
network at 100Mbps, you must use an un-
shielded twisted-pair (UTP) Category 5/5e
cable, or better data grade cabling. While a
Category 3 or 4 cable may initially seem to
work, it will soon cause data loss.
Step 5: Supply power to the FSD-504HP.
A. Connect one end of the power cable to the
Switch.
B. Connect the power plug of the power cable
to a standard wall outlet.
When the Switch receives power, the power LED should
remain solid Orange.
7. Product Specications
Model
FSD-504HP
4-Port 10/100Mbps 802.3af/at PoE +
1-Port 10/100Mbps Desktop Switch
Hardware Specications
Hardware Version 3
Network Connector 5-Port RJ45 for 10/100BASE-TX, auto
MDI/MDIX
PoE Inject Port 4-Port with 802.3af/at PoE injector
function (Port 1 to port 4)
LED Display
System: Power (Orange)
Per PoE port: PoE (Orange, port 1 to
port 4)
LNK/ACT (Green, port 1 to port 5)
Switch Architecture Store and Forward switch architecture
MAC Address Table 1K MAC address table with auto
learning function
EST Protection 6KV
Switch Fabric 1Gbps
Switch Throughput 0.74Mpps @64bytes
Maximum Packet Size 1536bytes
Flow Control Back pressure for half-duplex. IEEE
802.3x pause frame for full-duplex
Power Requirements DC 51V, 1.25A.
Power Consumption Max. 63 watts, 214 BTU
Dimensions
(W x D x H) 100 x 100 x 26mm
Weight 257g
Power over Ethernet
PoE Standard
IEEE 802.3af Power over Ethernet/PSE
IEEE 802.3at Power over Ethernet Plus/
PSE
PoE Power Supply Type End-span + mid-span
Power Pin Assignment 1/2(+), 4/5(+), 3/6(-), 7/8(-)
PoE Power Output
Per Port 51V DC, 300mA. max. 15.4
watts (IEEE 802.3af)
Per Port 51V DC, 600mA. max. 30
watts (IEEE 802.3at)
PoE Power Budget 60 watts
Number of PDs, 7 watts 4
Number of PDs, 15.4
watts 4
Number of PDs, 30
watts 2
Standard Conformance
EMI Safety FCC, CE
Standard Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
IEEE 802.3af
IEEE 802.3at
Ethernet
Fast Ethernet
Flow Control
Power over Ethernet
Power over Ethernet Plus
Environment
Operating Environment 0 ~ 50 degrees C
Storage Environment -10 ~ 70 degrees C
Operating Humidity 5 ~ 95%, relative humidity, non-
condensing
Storage Humidity 5 ~ 95%, relative humidity, non-
condensing
8. Customer Support
Thank you for purchasing PLANET products. You can
browse our online FAQ resource on PLANET Website
rst to check if it could solve your issue. If you need
more support information, please contact PLANET switch
support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2017.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All
other trademarks belong to their respective owners.

- 9 -
- 10 - - 12 - - 13 - - 14 -
- 11 -
B. Connect the other end of the cable to the
network devices such as routers, Ethernet
switches or NVRs (network video recorders).
Step 4: Connect your FSD-504HP to PoE PD devices.
A. Connect one end of a standard network
cable to any of the four 10/100Mbps RJ45
PoE+ ports (Port 1 to Port 4).
B. Connect the other end of the cable to the
802.3at/af powered devices.
DC Power Line (DC)
100BASE-TX UTP
PoE
100BASE-TX UTP with PoE
Office Building Office Area
Warehouse
Control Room
Office Building
FSD-504HP
IEEE 802.3af PoE
VoIP Phone
IEEE 802.3at
PoE IP Camera
Fixed IP Dome
IEEE 802.3af PoE Splitter
DC
IEEE 802.3af
PoE IP Camera
PoE Extender
PoE
PoE
PoE
PoE
Wall-mount Installation
Step 1: Please nd the wall that can mount the
FSD-504HP.
Step 2: Please refer to the picture below to screw the
two screws on the wall.
80mm
Step 3: Hang the FSD-504HP on the screws from the
wall.
Step 4: Repeat step 5 of Desktop Installation for
power supply to the FSD-504HP.
Note
Before mounting the device to the wall,
please check the location of the electrical
outlet and the length of the Ethernet cable.
Note
Cable distance for switch
If the “DIP Switch Mode” is set to
“Standard”, then the distance of UTP/
STP cable between the FSD-504HP and
PC/PD devices should not exceed 100
meters.
If the “DIP Switch Mode” is set to
“Extend”, then the cable distance be-
tween the FSD-504HP and PC/PD devices
should not exceed 250 meters.
Note
Make sure the wiring is correct
Category 3/4/5 cable can be used in 10
Mbps operation. To reliably operate your
network at 100Mbps, you must use an un-
shielded twisted-pair (UTP) Category 5/5e
cable, or better data grade cabling. While a
Category 3 or 4 cable may initially seem to
work, it will soon cause data loss.
Step 5: Supply power to the FSD-504HP.
A. Connect one end of the power cable to the
Switch.
B. Connect the power plug of the power cable
to a standard wall outlet.
When the Switch receives power, the power LED should
remain solid Orange.
7. Product Specications
Model
FSD-504HP
4-Port 10/100Mbps 802.3af/at PoE +
1-Port 10/100Mbps Desktop Switch
Hardware Specications
Hardware Version 3
Network Connector 5-Port RJ45 for 10/100BASE-TX, auto
MDI/MDIX
PoE Inject Port 4-Port with 802.3af/at PoE injector
function (Port 1 to port 4)
LED Display
System: Power (Orange)
Per PoE port: PoE (Orange, port 1 to
port 4)
LNK/ACT (Green, port 1 to port 5)
Switch Architecture Store and Forward switch architecture
MAC Address Table 1K MAC address table with auto
learning function
EST Protection 6KV
Switch Fabric 1Gbps
Switch Throughput 0.74Mpps @64bytes
Maximum Packet Size 1536bytes
Flow Control Back pressure for half-duplex. IEEE
802.3x pause frame for full-duplex
Power Requirements DC 51V, 1.25A.
Power Consumption Max. 63 watts, 214 BTU
Dimensions
(W x D x H) 100 x 100 x 26mm
Weight 257g
Power over Ethernet
PoE Standard
IEEE 802.3af Power over Ethernet/PSE
IEEE 802.3at Power over Ethernet Plus/
PSE
PoE Power Supply Type End-span + mid-span
Power Pin Assignment 1/2(+), 4/5(+), 3/6(-), 7/8(-)
PoE Power Output
Per Port 51V DC, 300mA. max. 15.4
watts (IEEE 802.3af)
Per Port 51V DC, 600mA. max. 30
watts (IEEE 802.3at)
PoE Power Budget 60 watts
Number of PDs, 7 watts 4
Number of PDs, 15.4
watts 4
Number of PDs, 30
watts 2
Standard Conformance
EMI Safety FCC, CE
Standard Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
IEEE 802.3af
IEEE 802.3at
Ethernet
Fast Ethernet
Flow Control
Power over Ethernet
Power over Ethernet Plus
Environment
Operating Environment 0 ~ 50 degrees C
Storage Environment -10 ~ 70 degrees C
Operating Humidity 5 ~ 95%, relative humidity, non-
condensing
Storage Humidity 5 ~ 95%, relative humidity, non-
condensing
8. Customer Support
Thank you for purchasing PLANET products. You can
browse our online FAQ resource on PLANET Website
rst to check if it could solve your issue. If you need
more support information, please contact PLANET switch
support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
[email protected]
Copyright © PLANET Technology Corp. 2017.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All
other trademarks belong to their respective owners.

- 9 -
- 10 - - 12 - - 13 - - 14 -
- 11 -
B. Connect the other end of the cable to the
network devices such as routers, Ethernet
switches or NVRs (network video recorders).
Step 4: Connect your FSD-504HP to PoE PD devices.
A. Connect one end of a standard network
cable to any of the four 10/100Mbps RJ45
PoE+ ports (Port 1 to Port 4).
B. Connect the other end of the cable to the
802.3at/af powered devices.
DC Power Line (DC)
100BASE-TX UTP
PoE
100BASE-TX UTP with PoE
Office Building Office Area
Warehouse
Control Room
Office Building
FSD-504HP
IEEE 802.3af PoE
VoIP Phone
IEEE 802.3at
PoE IP Camera
Fixed IP Dome
IEEE 802.3af PoE Splitter
DC
IEEE 802.3af
PoE IP Camera
PoE Extender
PoE
PoE
PoE
PoE
Wall-mount Installation
Step 1: Please nd the wall that can mount the
FSD-504HP.
Step 2: Please refer to the picture below to screw the
two screws on the wall.
80mm
Step 3: Hang the FSD-504HP on the screws from the
wall.
Step 4: Repeat step 5 of Desktop Installation for
power supply to the FSD-504HP.
Note
Before mounting the device to the wall,
please check the location of the electrical
outlet and the length of the Ethernet cable.
Note
Cable distance for switch
If the “DIP Switch Mode” is set to
“Standard”, then the distance of UTP/
STP cable between the FSD-504HP and
PC/PD devices should not exceed 100
meters.
If the “DIP Switch Mode” is set to
“Extend”, then the cable distance be-
tween the FSD-504HP and PC/PD devices
should not exceed 250 meters.
Note
Make sure the wiring is correct
Category 3/4/5 cable can be used in 10
Mbps operation. To reliably operate your
network at 100Mbps, you must use an un-
shielded twisted-pair (UTP) Category 5/5e
cable, or better data grade cabling. While a
Category 3 or 4 cable may initially seem to
work, it will soon cause data loss.
Step 5: Supply power to the FSD-504HP.
A. Connect one end of the power cable to the
Switch.
B. Connect the power plug of the power cable
to a standard wall outlet.
When the Switch receives power, the power LED should
remain solid Orange.
7. Product Specications
Model
FSD-504HP
4-Port 10/100Mbps 802.3af/at PoE +
1-Port 10/100Mbps Desktop Switch
Hardware Specications
Hardware Version 3
Network Connector 5-Port RJ45 for 10/100BASE-TX, auto
MDI/MDIX
PoE Inject Port 4-Port with 802.3af/at PoE injector
function (Port 1 to port 4)
LED Display
System: Power (Orange)
Per PoE port: PoE (Orange, port 1 to
port 4)
LNK/ACT (Green, port 1 to port 5)
Switch Architecture Store and Forward switch architecture
MAC Address Table 1K MAC address table with auto
learning function
EST Protection 6KV
Switch Fabric 1Gbps
Switch Throughput 0.74Mpps @64bytes
Maximum Packet Size 1536bytes
Flow Control Back pressure for half-duplex. IEEE
802.3x pause frame for full-duplex
Power Requirements DC 51V, 1.25A.
Power Consumption Max. 63 watts, 214 BTU
Dimensions
(W x D x H) 100 x 100 x 26mm
Weight 257g
Power over Ethernet
PoE Standard
IEEE 802.3af Power over Ethernet/PSE
IEEE 802.3at Power over Ethernet Plus/
PSE
PoE Power Supply Type End-span + mid-span
Power Pin Assignment 1/2(+), 4/5(+), 3/6(-), 7/8(-)
PoE Power Output
Per Port 51V DC, 300mA. max. 15.4
watts (IEEE 802.3af)
Per Port 51V DC, 600mA. max. 30
watts (IEEE 802.3at)
PoE Power Budget 60 watts
Number of PDs, 7 watts 4
Number of PDs, 15.4
watts 4
Number of PDs, 30
watts 2
Standard Conformance
EMI Safety FCC, CE
Standard Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
IEEE 802.3af
IEEE 802.3at
Ethernet
Fast Ethernet
Flow Control
Power over Ethernet
Power over Ethernet Plus
Environment
Operating Environment 0 ~ 50 degrees C
Storage Environment -10 ~ 70 degrees C
Operating Humidity 5 ~ 95%, relative humidity, non-
condensing
Storage Humidity 5 ~ 95%, relative humidity, non-
condensing
8. Customer Support
Thank you for purchasing PLANET products. You can
browse our online FAQ resource on PLANET Website
rst to check if it could solve your issue. If you need
more support information, please contact PLANET switch
support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2017.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All
other trademarks belong to their respective owners.