Planet MAP-3100 Quick start guide

PLANET Mesh Network Manager Guide
802.11a/b/g Indoor Wireless Mesh Network
Access Point
MAP-3100 / MAP-3120
Mesh Network Manager (MnM)
Management Utility User Manual
PLANET Mesh Network Manager Guide Page1 of 124

PLANET Mesh Network Manager Guide
Copyright
Copyright ©2008 by PLANET Technology Corp. All rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language
or computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove
defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes
the entire cost of all necessary servicing, repair, and any incidental or consequential damages
resulting from any defect in the software. Further, PLANET reserves the right to revise this publication
and to make changes from time to time in the contents hereof without obligation to notify any person
of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks
of their respective holders.
Revision
Mesh Network Manager User’s Manual for PLANET Wireless Mesh Access Point
Model: MAP-3100 / MAP-3120
Rev: 2.0 (February, 2008)
Part No. EM-MAP3K_MnMv2.doc
PLANET Mesh Network Manager Guide Page2 of 124

PLANET Mesh Network Manager Guide
Table of Content
Table of Content3
1Overview 6
2System Requirement7
3Utility Installation and Un-installation 8
3.1 Installation 8
3.1.1 Introduction 8
3.1.2 Choose Install Folder 9
3.1.3 Choose Shortcut Folder 9
3.1.4 Pre-Installation Summary 10
3.1.5 Installing 10
3.1.6 Installation Complete 11
3.2 Un-installation 11
3.2.1 Introduction 12
3.2.2 Uninstalling 12
3.2.3 Uninstallation Complete 13
4How to Use PLANET Mesh Network Management Tools 14
4.1 Quick Start 14
4.2 Software Overview & Features 15
4.2.1 Software Layout 15
4.2.1.1 Map Container 15
4.2.1.2 MIB Reader 16
4.2.1.3 Alarm Viewer 17
4.2.2 Toolbar Reference 18
4.2.3 Features 20
4.2.3.1 Create Map 20
4.2.3.2 Open Map 21
4.2.3.3 Save Map 21
4.2.3.4 Topology Map 22
4.2.3.5 Set up New Scan 23
4.2.3.6 Map View 24
4.2.3.7 Status Pane 25
4.2.3.8 Scan IP Address 26
4.2.3.9 SNMP Community / Passwords (for Scan-IP)26
4.2.3.10 Socket Port 28
4.2.3.11 SNMP Community / Passwords (for AP Unit) 28
4.2.3.12 Scan Interval 29
4.2.3.13 Import Background Image 30
4.2.3.14 Map Print 31
4.2.3.15 Map Zoom 32
4.2.3.16 Customize Map 33
4.2.3.17 Background Image Transparency 36
4.2.3.18 Block List 37
4.2.3.19 Lock / Unlock 38
4.2.3.20 Node details 39
PLANET Mesh Network Manager Guide Page3 of 124

PLANET Mesh Network Manager Guide
4.2.3.21 Client Properties 40
4.2.3.22 Get/Set using MIB Reader 41
4.2.3.23 Load/Unload MIB 44
4.2.3.24 Alarm Table 45
4.2.3.25 Add Trap Agent46
4.2.3.26 View Log Files 48
4.2.3.27 Show Route 49
4.2.3.28 Create VPN Connection 51
4.2.3.29 Configure Mesh APs 56
4.2.3.30 Discovery Tool 58
4.2.3.31 View Interface and Client Live Statistic 58
4.2.3.32 Logout Client60
5Configure the Mesh AP using AP Configurator 62
5.1 Overview of AP Configurator 62
5.2 How to use AP Configurator 63
5.3 Configure the Mesh AP 65
5.3.1.1 System > System 65
5.3.1.2 System > Syslog 67
5.3.1.3 System > Advanced Tuning 67
5.3.1.4 Network > Network 70
5.3.1.5 Network > WAN 71
5.3.1.6 Network > VLAN 75
5.3.1.7 Network > Mesh 77
5.3.1.8 Network > Wireless Configuration 80
5.3.1.9 Network > Route 83
5.3.1.10 Network > IP Sec 84
5.3.1.11 Network > L2TP Client86
5.3.1.12 Network > OLSR 87
5.3.1.13 Services > NTP 89
5.3.1.14 Services > DHCP 91
5.3.1.15 Services > MAC Access 93
5.3.1.16 Services > NAT 95
5.3.1.17 Services > Firewall 96
5.3.1.18 Services > Traffic Shaping 98
5.3.1.19 Services > PPTP Server 100
5.3.1.20 Services > Mobile IP (Future Feature) 102
5.3.1.21 Services > Captive Portal 103
5.3.1.22 Services > Radius 105
5.3.1.23 Services > Dynamic DNS 107
5.3.1.24 Services > Zero Config 108
5.3.1.25 Services > Auto IP 108
5.3.1.26 Services -> Route Watch Dog 109
5.3.1.27 Services -> System Watch Dog 110
5.3.1.28 Services -> SSHD 110
5.3.1.29 Services > WME 111
5.3.1.30 Management > HTTPD 113
5.3.1.31 Management > SNMPD 115
5.3.1.32 Management > SNMP Trap 117
5.3.1.33 Management > NMS Address 120
PLANET Mesh Network Manager Guide Page4 of 124

PLANET Mesh Network Manager Guide
5.3.1.34 Status > DHCP Client121
5.3.1.35 Command > Reboot 121
5.3.1.36 Command > Reset 122
5.3.1.37 Command > Download/Upload 122
6Technical Support 124
PLANET Mesh Network Manager Guide Page5 of 124

PLANET Mesh Network Manager Guide
1Overview
This document provides a details information and application guidance for the user of the
management software, the PLANET Mesh Network Manager (MnM). This network
management system is intended to perform an overall monitoring and configuring features for
the PLANET Mesh Network.
PLANET Mesh Network Manager Guide Page6 of 124

PLANET Mesh Network Manager Guide
2System Requirement
The PLANET Mesh Network Manager is written in JAVA, hence it has the feature of cross
platform, capable to run in most of the platform. The following are the recommended system
requirement.
-256 MB RAM (recommended minimum)
-10 MB hard disk space
-Microsoft Windows 2000, XP (recommended)
Besides, in order to enable the NMS to work properly, the following ports must be allowed
through any firewall between the NMS and the agent:
-Port 161 (by default) – Use for standard SNMP Get and Set
-Port 162 (by default) – Use for listen to SNMP Trap
-Port 4608 (by default) – Used by the Discovery Tool
-Port 8188 (by default) – Use to listen for the Layer-2 node’s notification
PLANET Mesh Network Manager Guide Page7 of 124

PLANET Mesh Network Manager Guide
3Utility Installation and Un-installation
3.1 Installation
Insert the bundled CD into the CD-ROM drive to launch the auto run program. Once
completed, a menu screen will appear. Click the “PLANET Mesh Network Manager” hyperlink
and select “Open” or “Run” to initiate the install wizard.
After the wizard completes preparation, follow the 6 easy steps directed by the wizard to
perform the installation.
3.1.1 Introduction
Simply explain what this software is about. Press Next to proceed.
PLANET Mesh Network Manager Guide Page8 of 124

PLANET Mesh Network Manager Guide
3.1.2 Choose Install Folder
Prompt user to choose the install path (directory) and name the install folder. Press Next to
proceed.
3.1.3 Choose Shortcut Folder
Specify where the software shortcut will be created at. Press Next to proceed.
PLANET Mesh Network Manager Guide Page9 of 124

PLANET Mesh Network Manager Guide
3.1.4 Pre-Installation Summary
Let user have a quick review about the installation settings before start installing. Press
Install button to start the installation.
3.1.5 Installing
Installation is in progress. Once the installation is completed it will direct the user to the next
step.
PLANET Mesh Network Manager Guide Page10 of 124

PLANET Mesh Network Manager Guide
3.1.6 Installation Complete
Indicating the installation is completed, and user can select to restart the system instantly or
afterward, in order to complete the installation. Press Done to conclude the installation. After
that, you may launch the NMS through the shortcut you created previously.
3.2 Un-installation
In order to uninstall the PLANET Mesh Network Manager from your terminal, you can get the
uninstaller wizard from the software directory. The uninstaller, namely Uninstall PLANET
Mesh Tools, is located at the Uninstall_PLANET Mesh Tools folder. Launch the uninstaller
wizard by double-click the executable file. Follows the following steps:
PLANET Mesh Network Manager Guide Page11 of 124

PLANET Mesh Network Manager Guide
3.2.1 Introduction
An introduction regarding the uninstallation of the PLANET Mesh Management Tool. Click
Uninstall to start the process.
3.2.2 Uninstalling
Uninstallation is in the progress. Once the progress is completed, it will automatically direct
you to the next step.
PLANET Mesh Network Manager Guide Page12 of 124

PLANET Mesh Network Manager Guide
3.2.3 Uninstallation Complete
The software is uninstalled. You may choose to restart the terminal instantly or afterward in
order to complete the process.
PLANET Mesh Network Manager Guide Page13 of 124

PLANET Mesh Network Manager Guide
4How to Use PLANET Mesh Network
Management Tools
4.1 Quick Start
First of all, make sure the terminal where you installed your PLANET Mesh Network
Management Tools is connected to the network, via Wireless or Wired LAN. Then, launch the
NMS at the location where you install it.
For a Layer 3 Mesh network:
Click the Create Map button on the toolbar to generate a new map profile. A dialog box would
appear, select SNMP Map and enter the name of the new profile. After that, hit the OK button
to complete the set up. Anew map will be inserted into the NMS.
Then, click on the drop-down list on the toolbar of the new profile, where it prompts users to
insert the Scan IP Address, the destination IP Address to be scanned. Enter the desired IP
and click the button next to the list to save the IP. Finally, select the Start Scan button on the
map’s toolbar, the scan will be initiated and run. The result of the scan will be plotted on the
map area. User is free to adjust the position of the found-unit on the map.
For a Layer 2 Mesh network:
Prior to set up the utility, user is required to add the IP address of the NMS terminal on the
web page (Management > NMS Addresses) of Layer 2 nodes.
After the Layer 2 node configuration is done, activate the NMS and click the Create Map
button. A dialog box would appear, select Layer-2 Map and enter the name of the new profile.
After that, hit the OK button to complete the setup. Anew map will be inserted into the NMS.
Before shutting down the NMS, user can save the profile settings, including the coordinate of
the found Mesh AP units on the map, by click on the Save Map button on the map toolbar.
The saved profile can be loaded directly to the NMS next time using the Open Map button on
the toolbar.
For further description regarding the functions and features of the PLANET Mesh Network
Management Tools, user may refer to the following section.
PLANET Mesh Network Manager Guide Page14 of 124

PLANET Mesh Network Manager Guide
4.2 Software Overview & Features
4.2.1 Software Layout
Before we proceed further, let us have an overview at the layout of the NMS. Basically, the
PLANET Mesh Network Management Tools is consists of three major sections:
Map Container
MIB Reader
Alarm Viewer
User can switch the view of the NMS by select the tabs at the left bottom corner, as illustrated,
or through the menu bar.
4.2.1.1 Map Container
The Map Container is the section where user can monitor and manage the mesh network.
The network will be displayed in the form of graphical topology map, and the status will be
updated periodically.
The center frame of the Map Container is the space to plot the topology map. More than one
map can be created and run simultaneously. The status of the map will be logged to the
status pane at the bottom of the map. Each topology map has its own status pane.
The panel at the left of the map space is the Node Details panel. It is used to display the
properties of the selected Mesh AP unit on the topology map. The information of the AP will
be loaded into the table, and the graph below the table shows the signal strength between the
selected AP with its neighbour APs. The column at the bottom of this panel is used to invoke
the live stat monitoring feature.
The right panel, meanwhile, is to display the details of the clients associated to the Mesh AP
unit. The panel is divided into two parts, the Client Properties and Client Signal Strength
portion. Each portion will be automatically updated every minute, to provide the admin user
PLANET Mesh Network Manager Guide Page15 of 124

PLANET Mesh Network Manager Guide
the live result regarding the clients.
4.2.1.2 MIB Reader
The MIB Reader provides user a simple user-interface to retrieve as well as configure the
settings of the Mesh AP unit through the standard or vendor proprietary MIB files. With the
correct community and password, user can perform the SNMP actions such as SNMPGet,
SNMPSet and SNMPTable.
PLANET Mesh Network Manager Guide Page16 of 124

PLANET Mesh Network Manager Guide
The left pane displays the list of MIB and its tree. User can load and unload MIB file from the
desired location. More than one file can be loaded into the MIB Reader. In order to read or set
an item, expand the MIB tree, select the desired node. Select the SNMP version; fill in the IP
Address and other necessary keyword. Then click on the command button (SnmpGet,
SnmpSet, SnmpWalk, Load Table, etc..) on the toolbar. The output will be shown on the
Output column.
4.2.1.3 Alarm Viewer
The Alarm Viewer is a trap receiver. It received the SNMP alarms and notifications directed by
the Mesh AP units and display in the table at the center frame. Select the table entry in order
to view the description of the trap.
Note that the table is a read-only table, which displays the trap’s source IP Address,
description, severity and the time when the trap or alarm was caught. These alarms should be
deleted once they were reviewed and resolved, by clicking the Delete button.
PLANET Mesh Network Manager Guide Page17 of 124

PLANET Mesh Network Manager Guide
4.2.2 Toolbar Reference
This section provides a quick reference for the buttons in the toolbar of the NMS. The
description of the toolbar of the NMS is illustrated at the table below:
Button Name Function
Create Map Create a new topology map profile
Open Map Open a pre-saved topology map profile
View Tile View the topology map in grid layout
View Cascade View the topology map in cascade layout
SnmpGet SnmpGet the data from MIB tree
SnmpSet SnmpSet the data from MIB tree
Load Table Load the SNMP table from MIB tree
Refresh Table Refresh the SNMP table from MIB tree
PLANET Mesh Network Manager Guide Page18 of 124

PLANET Mesh Network Manager Guide
Add Table Row Add a row to SNMP Table
Del Table Row Delete a row from SNMP Table
SnmpWalk Walk the selected item from the MIB tree
Start Trap Initiate the Alarm Host system
Stop Trap Stop the Alarm Host system
On the other hand, the following table shows the description of the toolbar of the map
container:
Button Name Function
Import
Background
Import an image file to use as the background
image of the topology map
Save Profile Save the current topology map
Scan Start Start the network scanning (SNMP Map only)
Scan Stop Stop the network scanning (SNMP Map only)
Initiate Port Open port to listen to Layer-2 notification (Layer-2
Map only)
Close Port Close Layer-2 notification port (Layer-2 Map only)
Zoom In Zoom in the topology map by 25%
Zoom Out Zoom out the topology map by 25%
Zoom Fit Zoom the topology map to a size that fit the
screen
Lock Lock the AP units on the map
Unlock Unlock the AP units on the map
Block List Open the block list window
PLANET Mesh Network Manager Guide Page19 of 124

PLANET Mesh Network Manager Guide
4.2.3 Features
4.2.3.1 Create Map
In the NMS, two topology maps are available: SNMP Map and Layer-2 Map. These two types
of map look similar. The main difference between them is the method to get the topology
information.
•The SNMP Map is the ordinary type, where it uses the SNMP protocol to collect the
topology from the nodes discovered, and then plot the map using the collaborate data.
•Whereas the Layer-2 Map opens a specific port to listen for the notification from the
nodes, in order to plot the map. Prior to this, user is required to add the information of
the NMS terminal (IP Address) to the node. Thus in fact, the Layer-2 Map can receive
the notification not only from the layer-2 mode AP, but any other mode as well, as
long as the NMS Address table is set.
In order to create a new Topology map profile, user can click on the Create New button on
the main toolbar, or select File > Create New from the menu bar. A window would turn out to
prompt user for the type and name of the new map. User may select the type of the profile
from the drop down list, and enter the name in the provided column.
Please be aware that special character such as #, $, % (except _), are not allowed to use as
the name of the topology map name to avoid data corruption, since the name of the map will
be used as the header of their data file. On the other hand, the system also not allow user to
create a new profile with the name of the existing map in the NMS.
Two Profile Types can be found, SNMP Map and Layer 2 Map. Please chose SNMP Map for
Layer 3 mode Mesh Network Management and Layer 2 Map for Layer 2 Mode Mesh Network
Management.
Hit the OK button to proceed, or Cancel to close the window.
PLANET Mesh Network Manager Guide Page20 of 124