Planet WNAP-6325 User manual

I

Copyright
Copyright 2015 by PLANET Technology Corp. All rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language
or computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs
prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer)
assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves the right to revise
this publication and to make changes from time to time in the contents hereof without obligation to
notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks
of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class Bdigital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
nt. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his/her own
expense. Any changes or modifications not expressly approved by PLANET could void the user’s
authority to operate this equipment under the rules and regulations of the FCC.
environme
FCC Caution:
To assure continued compliance, (for example, use only shielded interface cables when connecting
to computer or peripheral devices) any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity
to the antenna shall not be less than 20 cm (8 inches) during normal operation.
I

CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation. For energy saving, please
remove the DC-plug to disconnect the device from the power circuit. Without removing the DC-plug,
the device still consumes power from the power circuit. In view of Saving the Energy, it is strongly
suggested to remove the DC-plug for the device if this device is not intended to be active.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication
terminal Equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive
repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and
Satellite Earth Station Equipment) as of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when
working with electrical equipment. All guidelines of this and of the computer manufacture must
therefore be allowed at all times to ensure the safe use of the equipment.
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users of
electrical and electronic equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and thus,
WEEE has to be collected separately.
II

Revision
User’s Manual of PLANET 300Mbps 802.11n Wireless Outdoor CPE
Model: WNAP-6325
Rev: 1.0 (January, 2015)
Part No. EM-WNAP-6325_v1.0 (2081-E10590-000)
III

CONTENTS
Chapter 1.Product Introduction...........................................................................................................8
1.1 Package Contents ...............................................................................................................8
1.2 Product Description............................................................................................................9
1.3 Product Features...............................................................................................................10
1.4 Product Specifications ..................................................................................................... 11
Chapter 2.Hardware Installation ........................................................................................................13
2.1 Hardware Description .......................................................................................................13
2.1.1 The Bottom Panel – Port ........................................................................................14
Chapter 3.Connecting to the AP ........................................................................................................ 17
3.1 Preparation before Installation ........................................................................................17
3.1.1 Professional Installation Required ..........................................................................17
3.1.2 Safety Precautions..................................................................................................17
3.2 Installation Precautions....................................................................................................17
3.3 Installing the AP ................................................................................................................19
Chapter 4.Quick Installation Guide ................................................................................................... 21
4.1 Manual Network Setup - TCP/IP Configuration ..............................................................21
4.1.1 Configuring the IP Address Manually .....................................................................21
4.2 Starting Setup in the Web UI............................................................................................24
Chapter 5.Configuring the AP............................................................................................................28
5.1 Operation Mode.................................................................................................................28
5.1.1 Access Point ...........................................................................................................28
5.1.2 Client.......................................................................................................................30
5.1.3 WDS AP..................................................................................................................31
5.1.4 WDS Client .............................................................................................................32
5.1.5 AP Router ...............................................................................................................33
5.1.6 Wireless ISP ...........................................................................................................34
5.1.7 Security Setting.......................................................................................................35
5.1.8 Advanced Settings..................................................................................................39
5.1.9 Access Control........................................................................................................42
5.1.10 WAN Port Settings..................................................................................................43
5.1.11 Dynamic DNS Settings ...........................................................................................45
5.1.12 Remote Management .............................................................................................50
5.1.13 DHCP Server Settings ............................................................................................ 50
5.1.14 DMZ Settings ..........................................................................................................51
5.1.15 Virtual Server Settings............................................................................................52
5.1.16 IP Filtering Settings.................................................................................................52
5.1.17 Port Filtering Settings .............................................................................................53
5.1.18 MAC Filtering Settings............................................................................................53
IV

5.1.19 Bandwidth Control ..................................................................................................54
5.1.20 SNMP......................................................................................................................55
5.2 System Configuration....................................................................................................... 56
5.2.1 Default IP Settings ..................................................................................................56
5.2.2 Time Settings..........................................................................................................57
5.2.3 Password Settings..................................................................................................58
5.2.4 System Management..............................................................................................58
5.2.5 Ping Watchdog........................................................................................................59
5.2.6 Firmware Upgrade..................................................................................................60
5.2.7 Configuration Save and Restore ............................................................................60
5.2.8 Factory Default .......................................................................................................61
5.2.9 Reboot System .......................................................................................................61
5.2.10 Schedule Reboot ....................................................................................................61
5.3 Tools ...................................................................................................................................64
5.3.1 Network Ping ..........................................................................................................64
5.3.2 Network Traceroute ................................................................................................64
5.4 Device Status.....................................................................................................................66
5.4.1 Device Information..................................................................................................66
5.4.2 Wireless Information...............................................................................................67
5.4.3 LAN Information......................................................................................................68
5.4.4 Wireless Client Table ..............................................................................................69
5.4.5 System Log.............................................................................................................70
5.5 Logout ................................................................................................................................71
Appendix A: Troubleshooting............................................................................................................72
Appendix B: Use Planet Smart Discovery to find AP ...................................................................... 74
Appendix C: FAQ.................................................................................................................................75
Q1: How to set up the AP Client Connection...........................................................................75
Q2: How to set up the WDS Connection ..................................................................................83
V

FIGURES
FIGURE 2-1 THREE-WAY VIEW..................................................................................................................13
FIGURE 2-2 LED .....................................................................................................................................14
FIGURE 2-3 BOTTOM PANEL.....................................................................................................................15
FIGURE 2-4 POEINJECTOR......................................................................................................................15
FIGURE 3-1 CONNECT THE ANTENNA ........................................................................................................19
FIGURE 3-2 CONNECT THE ETHERNET CABLE............................................................................................19
FIGURE 3-3 CONNECT THE POEINJECTOR................................................................................................20
FIGURE 3-4 POLE MOUNTING...................................................................................................................20
FIGURE 4-1 TCP/IP SETTING...................................................................................................................22
FIGURE 4-2 WINDOWS START MENU ........................................................................................................23
FIGURE 4-3 SUCCESSFUL RESULT OF PING COMMAND ...............................................................................23
FIGURE 4-4 FAILED RESULT OF PING COMMAND ........................................................................................24
FIGURE 4-5 LOGIN BY DEFAULT IP ADDRESS..............................................................................................24
FIGURE 4-6 LOGIN WINDOW.....................................................................................................................25
FIGURE 4-7 WNAP-6325 WEB UI SCREENSHOT ......................................................................................26
FIGURE 4-8 CHOOSE OPERATION MODE...................................................................................................26
FIGURE 4-9 CONFIGURE WIRELESS SETTINGS ..........................................................................................27
FIGURE 5-1 MAIN MENU ..........................................................................................................................28
FIGURE 5-2 OPERATION MODE.................................................................................................................28
FIGURE 5-3 BASIC SETTINGS -AP............................................................................................................29
FIGURE 5-4 BASIC SETTINGS -CLIENT......................................................................................................30
FIGURE 5-5 BASIC SETTINGS –WDS AP..................................................................................................32
FIGURE 5-6 BASIC SETTINGS –WDS CLIENT............................................................................................33
FIGURE 5-7 BASIC SETTINGS –AP ROUTER .............................................................................................34
FIGURE 5-8 BASIC SETTINGS –WISP ......................................................................................................35
FIGURE 5-9 SECURITY SETTINGS .............................................................................................................35
FIGURE 5-10 SECURITY SETTINGS –WEP ...............................................................................................36
FIGURE 5-11 SECURITY SETTINGS –WPA PERSONAL ...............................................................................37
FIGURE 5-12 SECURITY SETTINGS –WPA ENTERPRISE ............................................................................37
FIGURE 5-13 SECURITY SETTINGS –WPA2 PERSONAL.............................................................................38
FIGURE 5-14 SECURITY SETTINGS –WPA2 ENTERPRISE..........................................................................38
FIGURE 5-15 SECURITY SETTINGS –WPA-MIXED PERSONAL....................................................................39
FIGURE 5-16 SECURITY SETTINGS –WPA-MIXED ENTERPRISE.................................................................39
FIGURE 5-17 ADVANCED SETTINGS ..........................................................................................................40
FIGURE 5-18 WMM CONFIGURATION .......................................................................................................41
FIGURE 5-19 ACCESS CONTROL ..............................................................................................................43
FIGURE 5-20 WAN PORT SETTINGS –DHCP...........................................................................................43
FIGURE 5-21 WAN PORT SETTINGS –STATIC IP.......................................................................................44
FIGURE 5-22 WAN PORT SETTINGS –PPPOE.........................................................................................45
FIGURE 5-23 DYNAMIC DNS SETTINGS ....................................................................................................45
FIGURE 5-24 REMOTE MANAGEMENT .......................................................................................................50
FIGURE 5-25 DHCP SERVER SETTINGS ...................................................................................................51
VI

VII
FIGURE 5-26 DMZ SETTINGS...................................................................................................................51
FIGURE 5-27 VIRTUAL SERVER SETTINGS.................................................................................................52
FIGURE 5-28 IP FILTERING SETTINGS.......................................................................................................52
FIGURE 5-29 PORT FILTERING SETTINGS..................................................................................................53
FIGURE 5-30 MAC FILTERING SETTINGS ...................................................................................................53
FIGURE 5-31 BANDWIDTH CONTROL SETTINGS .........................................................................................54
FIGURE 5-32 SNMP SETTINGS ................................................................................................................55
FIGURE 5-33 SYSTEM CONFIGURATION DEFAULT PAGE ..............................................................................56
FIGURE 5-34 DEFAULT IP SETTINGS .........................................................................................................56
FIGURE 5-35 TIME SETTINGS ...................................................................................................................57
FIGURE 5-36 PASSWORD SETTINGS .........................................................................................................58
FIGURE 5-37 SYSTEM MANAGEMENT........................................................................................................58
FIGURE 5-38 PING WATCHDOG ................................................................................................................59
FIGURE 5-39 FIRMWARE UPGRADE ..........................................................................................................60
FIGURE 5-40 CONFIGURATION SAVE AND RESTORE...................................................................................60
FIGURE 5-41 FACTORY DEFAULT ..............................................................................................................61
FIGURE 5-42 REBOOT SYSTEM ................................................................................................................61
FIGURE 5-43 SCHEDULE REBOOT ............................................................................................................62
FIGURE 5-44 SCHEDULE REBOOT -EXAMPLE ...........................................................................................63
FIGURE 5-45 NETWORK PING ..................................................................................................................64
FIGURE 5-46 NETWORK TRACEROUTE......................................................................................................65
FIGURE 5-47 DEVICE STATUS...................................................................................................................66
FIGURE 5-48 DEVICE INFORMATION..........................................................................................................67
FIGURE 5-49 WIRELESS INFORMATION .....................................................................................................68
FIGURE 5-50 LAN INFORMATION ..............................................................................................................69
FIGURE 5-51 WIRELESS CLIENT TABLE.....................................................................................................69
FIGURE 5-52 SYSTEM LOG ......................................................................................................................70
FIGURE 5-53 LOGOUT..............................................................................................................................71
FIGURE 5-54 RE-LOGIN ...........................................................................................................................71

User Manual of WNAP-6325
-8-
Chapter 1.Product Introduction
1.1 Package Contents
Thank you for choosing PLANET WNAP-6325. Before installing the AP, please verify the contents inside the
package box.
WNAP-6325 Quick Installation Guide
PoE Injector & Power Cord Plastic Strap x 1
If there is any item missing or damaged, please contact the seller
immediately.

User Manual of WNAP-6325
-9-
1.2 Product Description
Cost-effective Wireless Solution with Superior Performance
PLANET WNAP-6325 is designed to provide a highly-stable, better performance and cost-effective wireless
solution in outdoor wireless deployment. With the same transmission power, it offers better significant range and
excellent throughput than those of the traditional 802.11g wireless device. Via the embedded 12dBi
dual-polarization (vertical and horizontal) directional antenna, it provides good diversity coverage and better
noise immunity effect, thus heightening the performance of a long-distance, outdoor connectivity even though
the environment is flooded with many 2.4GHz wireless equipment.
Designed for Various Requirements
The WNAP-6325 is dedicatedly designed for WISP solution that provides CPE users with Internet access via the
WISP provider in rural areas. Besides, it caters to various wireless communication connectivities (AP / Client /
WDS PtP / WDS PtMP / WISP), thus meeting users’ application requirements.
Advanced Security and Rigorous Authentication
The WNAP-6325 supports WEP, WPA / WPA2, WPA-PSK and WPA2-PSK wireless encryptions, the advanced
WPA2-AES mechanism and 802.1X RADIUS authentication, which can effectively prevent eavesdropping by
unauthorized users or bandwidth occupied by unauthenticated wireless access. Furthermore, any users are
granted or denied access to the wireless LAN network based on the ACL (Access Control List) that the
administrator pre-established. In addition, with the multiple-SSIDs feature, you can set up different wireless
networks. The WNAP-6325 can therefore serve as a virtual access point for segmented networks tailored to any
industrial need.
Flexible and Reliable Outdoor Characteristics
The WNAP-6325 is definitely suitable for such applications as IP surveillance, backhaul link of building to
building and backbone of public service. Additionally, the self-healing/schedule reboot capability keeps
connection alive all the time. Meeting the IP55 rating for outdoor UV resistant enclosure, the WNAP-6325 can
perform normally under rigorous weather conditions, meaning it can be installed in any harsh, outdoor
environments. With the proprietary Power over Ethernet (PoE) design, the WNAP-6325 can be easily installed in
the areas where power outlets are not available.
Easy Deployment and Management
With user-friendly Web UI and step-by-step setup wizard, the WNAP-6325 is easy to install, even for users who
never experience in setting up a wireless network. Furthermore, with the Planet Smart Discovery Utility and
SNMP-based management interface, the WNAP-6325 is convenient to be managed and configured remotely.

User Manual of WNAP-6325
-10-
1.3 Product Features
Industrial Compliant Wireless LAN and LAN
Compliant with the IEEE 802.11n wireless technology (with data rate of up to 300Mbps)
Backward compatible with 802.11g standard
Equipped with 10/100Mbps RJ45 ports for LAN and WAN; auto MDI/ MDI-X supported
Fixed-network Broadband Router
Supported connection types: Dynamic IP, Static IP, PPPoE
Supports virtual server and DMZ for various networking applications
Supports DHCP server, UPnP and Planet DDNS
RF Interface Characteristics
Built-in 12dBi dual-polarization antenna
High output power up to 500mW with multiply-adjustable transmit power control
Outdoor Environmental Characteristics
IP55 enclosure
Passive Power over Ethernet design
Operating temperature: -20~70°C
Multiple Operations and Wireless Modes
Multiple operation modes: Bridge, WISP
Multiple wireless modes: AP, Client CPE (WISP), WDS PtP, WDS PtMP
Supports multiple SSIDs to allow users to access different networks through a single AP
Supports WMM (Wi-Fi multimedia)
Secure Network Connection
Supports software Wi-Fi Protected Setup (WPS)
Advanced security: 64/128-bit WEP, WPA / WPA2, WPA-PSK / WPA2-PSK (TKIP/AES) and
802.1x RADIUS authentication
Supports IP / Protocol-based access control and MAC filtering
Easy Installation and Management
Web-based UI and quick Setup Wizard for easy configuration
Planet Smart Discovery Utility allows administrator to discover and locate each AP
SNMP-based management interface
System status monitoring includes DHCP Client and System Log

User Manual of WNAP-6325
-11-
1.4 Product Specification
Product WNAP-6325
300Mbps 802.11n Wireless Outdoor CPE
Hardware
Standard Support
IEEE802.11b/g/n
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
Chipset Atheros AR9344
Memory 64 Mbytes DDR SDRAM
16 Mbytes Flash
PoE Passive PoE
Interface
Wireless IEEE802.11b/g/n, 2T2R
PoE LAN (LAN 1): 1 x 10/100BASE-TX, auto-MDI/MDIX, passive PoE
LAN 2: 1 x 10/100BASE-TX, auto-MDI/MDIX, passive PoE out pass-through
Antenna
Built-in 12dBi Dual-Polarization Antenna
- Horizontal: 30 degrees
- Vertical: 20 degrees
Data Rate
IEEE 802.11b: 1, 2, 5.5, 11Mbps
IEEE 802.11g: up to 54Mbps
IEEE 802.11n (20MHz): up to 150Mbps
IEEE 802.11n (40MHz): up to 300Mbps
Media Access Control CSMA/CA
Modulation Transmission/Emission type: OFDM
Data modulation type: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
Frequency Band 2.412GHz ~ 2.484GHz
Operating Channel
America/ FCC: 2.414~2.462GHz (11 Channels)
Europe/ ETSI: 2.412~2.472GHz (13 Channels)
Japan/ TELEC: 2.412~2.484GHz (14 Channels)
RF Output Power (dBm)
IEEE 802.11b: up to 26 ± 1dBm
IEEE 802.11g: up to 23 ± 1dBm
IEEE 802.11n: up to 22 ± 1dBm
Receiver Sensitivity
(dBm)
IEEE 802.11b: -94dBm
IEEE 802.11g: -91dBm
IEEE 802.11n: -89dBm
Output Power Control 12~27Bm
Power Consumption 12W
Power Requirements
LAN 24VDC, 1A/ Passive PoE
Pin 4,5 VDC+
Pin 7,8 VDC-
Pin 3 Reset
Environment & Certification

User Manual of WNAP-6325
-12-
Operating Temperature -20~70°c
Operating Humidity 10~95% non-condensing
IP Level IP55
Regulatory CE, FCC, RoHS
Software
Built-in DHCP server supporting static IP address distributing
LAN Support 802.1d STP (Spanning Tree)
WAN
Static IP
Dynamic IP
PPPoE
Operation Modes Bridge
WISP
NAT firewall with SPI (Stateful Packet Inspection)
Built-in NAT server supporting Virtual Server, and DMZ
Firewall
Built-in firewall with Port/ IP address/ MAC/ URL filtering
Wireless Modes
AP
Client
WDS PTP
WDS PTMP
WISP
Channel Width 20MHz / 40MHz
Wireless Isolation Enable it to isolate each connected wireless client so that they cannot access
mutually.
Encryption Type 64/128-bit WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X
Provides wireless LAN ACL (Access Control List) filtering
Wireless MAC address filtering
Wireless Security
Enable/Disable SSID Broadcast
Max. Wireless Clients 25
Max. WDS AP 8
Max. Wired Clients 60
WMM Supports Wi-Fi multimedia
QoS Supports Quality of Service for bandwidth control
NTP Network Time Management
Self Healing Supports Schedule Reboot
Management Web UI, DHCP Client, Configuration Backup & Restore, Dynamic DNS, SNMP
Diagnostic Tool System Log, Ping Watchdog

User Manual of WNAP-6325
-13-
Chapter 2.Hardware Installation
Please follow the instructions below to connect the WNAP-6325 to the existing network devices and your
computers.
2.1 Hardware Description
Dimensions: 127 x 63 x 254 mm (W x D x H)
Figure 2-1 Three-way View

User Manual of WNAP-6325
-14-
Rear Panel – LED
Figure 2-2 LED
LED Definition
LED State Meaning
On System On
Power Off System Off
On Wi-Fi On
Wireless Off Wi-Fi Off
On Port linked.
LAN 1 Off No link.
On Port linked.
LAN 2 Off No link.
Table 2-1 The LED indication
2.1.1 The Bottom Panel – Port
The Bottom panel provides the physical connectors connected to the power adapter and any other network
device. Figure 2-3 shows the bottom panel of the WNAP-7325.

User Manual of WNAP-6325
-15-
Bottom Panel
Figure 2-3 Bottom Panel
PoE Injector
Reset Button
Figure 2-4 PoE Injector
H/W Interface Definition
Object Description
PoE LAN
(Passive PoE)
10/100Mbps RJ45 port , auto MDI/ MDI-X and passive PoE supported
Connect LAN port to the PoE injector to power on the device.
Pin assignment:
Pin 4, 5 (+)
Pin 7, 8 (-)
Pin 3 (Reset)
LAN 2
10/100Mbps RJ45 port, auto MDI/ MDI-X
Connect this port to the network equipment.
※When the option “Enable POE Passthrough” on the System Management
page is checked, the LAN2 can supply passive PoE power to the second
WNAP-7325 or WNAP-6325 through LAN 2.

User Manual of WNAP-6325
-16-
Reset
Press the Reset button on the device or on the PoE injector over 5
seconds to return to factory default setting.
※If you have connected with the thunder protector like PLANET
ELA-100, please DO NOT press the reset button on the PoE injector to
prevent the ELA-100 from being damaged. Remove the thunder
protector before push the reset button.
Table 2-2 The PoE Injector Indication

User Manual of WNAP-6325
-17-
Chapter 3.Connecting to the AP
3.1 Preparation before Installation
3.1.1 Professional Installation Required
Please seek assistance from a professional installer who is well trained in the RF installation and knowledgeable
in the local regulations.
3.1.2 Safety Precautions
1. To keep you safe and install the hardware properly, please read and follow these safety precautions.
2. If you are installing the WNAP-6325 for the first time, for your safety as well as others’, please seek
assistance from a professional installer who has received safety training on the hazards involved.
3. Keep safety as well as performance in mind when selecting your installation site, especially where there
are electric power and phone lines.
4. When installing the WNAP-6325, please note the following things:
Do not use a metal ladder;
Do not work on a wet or windy day;
Wear shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket.
5. When the system is operational, avoid standing directly in front of it. Strong RF fields are present when the
transmitter is on.
3.2 Installation Precautions
Users MUST use a proper and well-installed surge arrestor and grounding kit with WNAP-6325;
otherwise, a random lightning could easily cause fatal damage to the WNAP-6325. EMD (Lightning)
DAMAGE IS NOT COVERED UNDER WARRANTY.
Users MUST use the “Power cord and PoE Injector” shipped in the box with the WNAP-6325. Use of
other options will cause damage to the WNAP-6325.

User Manual of WNAP-6325
-18-
OUTDOOR INSTALLATION WARNING
IMPORTANT SAFETY PRECAUTIONS:
LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with the
equipment you are installing.
CONTACTING POWER LINES CAN BE LETHAL. Make sure no power
lines are anywhere where possible contact can be made. Antennas, masts,
towers, guy wires or cables may lean or fall and contact these lines. People
may be injured or killed if they are touching or holding any part of
equipment when it contacts electric lines. Make sure that equipment or
personnel do not come in contact directly or indirectly with power lines.
The horizontal distance from a tower, mast or antenna to the nearest
power line should be at least twice the total length of the mast/antenna combination. This will ensure that the mast will not
contact power if it falls either during installation or later.
TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.
!
Select equipment locations that will allow safe, simple equipment installation.
Don’t work alone. A friend or co-worker can save your life if an accident happens.
Use approved non-conducting lasers and other safety equipment. Make sure all equipment is in good repair.
If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.
If anything such as a wire or mast does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO
MOVE IT. Instead, save your life by calling the power company.
Don’t attempt to erect antennas or towers on windy days.
MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO
ANTENNAS HAVE LIGHTNING ARRESTORS. This will help prevent fire damage or human injury in case of lightning, static
build-up, or short circuit within equipment connected to the antenna.
The base of the antenna mast or tower must be connected directly to the building protective ground or to one or more
approved grounding rods, using 1 OAWG ground wire and corrosion-resistant connectors.
Refer to the National Electrical Code for grounding details.
IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:
DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.
Use a non-conductive dry board, stick or rope to push or drag them so they no longer are in contact with electrical
power.
Once they are no longer contacting electrical power, administer CPR if you are certified, and make sure that emergency
medical aid has been requested.

User Manual of WNAP-6325
-19-
3.3 Installing the AP
Please install the AP according to the following Steps. Don't forget to pull out the power plug and keep your
hands dry.
Step 1. Push the latch on the bottom of the WNAP-6325 to remove the sliding cover.
Figure 3-1 Connect the Antenna
Step 2. Plug the RJ45 Ethernet cable into the PoE LAN Port of the WNAP-6325. Then, slide back the cover of
the WNAP-6325 to finish the installation.
Figure 3-2 Connect the Ethernet cable