Planet WNAP-6306 User manual

User’s Manual of WNAP-6306
- 1 -

User’s Manual of WNAP-6306
Copyright
Copyright 2012 by PLANET Technology Corp. All rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language
or computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs
prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer)
assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves the right to revise
this publication and to make changes from time to time in the contents hereof without obligation to
notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks
of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution:
To assure continued compliance, (example-use only shielded interface cables when connecting to
computer or peripheral devices) any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two
conditions:
(1) This device may not cause harmful interference
(2) This Device must accept any interference received, including interference that may cause
undesired operation.
- 2 -

User’s Manual of WNAP-6306
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity
to the antenna shall not be less than 20 cm (8 inches) during normal operation.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation.
For energy saving, please remove the DC-plug to disconnect the device from the power circuit.
Without remove the DC-plug, the device still consuming power from the power circuit. In the view of
Saving the Energy and reduce the unnecessary power consuming, it is strongly suggested to
remove the DC-plug for the device if this device is not intended to be active.
Protection requirements for health and safety – Article 3.1a
Testing for electric safety according to EN 60950 has been conducted. These are considered
relevant and sufficient.
Protection requirements for electromagnetic compatibility – Article 3.1b
Testing for electromagnetic compatibility according to EN 301 489-1, EN 301 489-17 and EN 55024
has been conducted. These are considered relevant and sufficient.
Effective use of the radio spectrum – Article 3.2
Testing for radio test suites according to EN 300 328-2 has been conducted. These are considered
relevant and sufficient.
CE in which Countries where the product may be used freely:
Germany, UK, Italy, Spain, Belgium, Netherlands, Portugal, Greece, Ireland, Denmark, Luxembourg,
Austria, Finland, Sweden, Norway and Iceland.
France: except the channel 10 through 13, law prohibits the use of other channels.
- 3 -

User’s Manual of WNAP-6306
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication
terminal Equipment and the mutual recognition of their conformity (R&TTE).
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications
Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when
working with electrical equipment. All guidelines of this and of the computer manufacture must
therefore be allowed at all times to ensure the safe use of the equipment.
National Restrictions
This device is intended for home and office use in all EU countries (and other countries following the
EU directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country Restriction Reason/remark
Bulgaria None General authorization required for outdoor use and
public service
France Outdoor use limited to 10
mW e.i.r.p. within the band
2454-2483.5 MHz
Military Radiolocation use. Refarming of the 2.4 GHz
band has been ongoing in recent years to allow current
relaxed regulation. Full implementation planned 2012
Italy None If used outside of own premises, general authorization is
required
Luxembourg None General authorization required for network and service
supply(not for spectrum)
Norway Implemented This subsection does not apply for the geographical area
within a radius of 20 km from the centre of Ny-Ålesund
Russian Federation None Only for indoor applications
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users of
electrical and electronic equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.
- 4 -

User’s Manual of WNAP-6306
Revision
User’s Manual for PLANET 802.11n Wireless Outdoor Access Point
Model: WNAP-6306
Rev: 1.0 (April, 2012)
- 5 -

User’s Manual of WNAP-6306
Table of Contents
Chapter 1. Product Introduction..........................................................................................................9
1.1 Package contents..................................................................................................................9
1.2 Product Description .............................................................................................................9
1.3 Product Features.................................................................................................................12
1.4 Product Specification .........................................................................................................13
1.5 Wireless Performance ........................................................................................................15
Chapter 2. Hardware Description ......................................................................................................16
2.1 LED Panel............................................................................................................................. 16
2.2 LED Indications ...................................................................................................................16
2.3 Port & Connector.................................................................................................................17
2.4 PoE Injector .........................................................................................................................18
Chapter 3. Hardware installation .......................................................................................................19
3.1 Preparation before Installation .......................................................................................... 19
3.1.1 Professional Installation Required ..............................................................................19
3.1.2 Safety Precautions......................................................................................................19
3.1.3 Installation Precautions...............................................................................................19
3.2 Hardware Installation .......................................................................................................... 22
3.2.1 Connect Up .................................................................................................................22
Chapter 4. Software Installation ........................................................................................................24
4.1 Software Configuration.......................................................................................................24
4.2 Connecting the AP ..............................................................................................................24
4.3 Web Login ............................................................................................................................28
Chapter 5. Basic System Settings.....................................................................................................30
5.1 System Information ............................................................................................................30
5.1.1 System ........................................................................................................................30
5.1.2 LAN Info ......................................................................................................................30
5.1.3 Wireless Info ...............................................................................................................30
5.1.4 Secondary AP .............................................................................................................31
5.1.5 Statistics ......................................................................................................................32
5.2 System Log..........................................................................................................................32
5.3 Internet Setup......................................................................................................................33
5.3.1 WISP ...........................................................................................................................33
5.3.2 WAN Type ...................................................................................................................34
5.4 Wireless Management ........................................................................................................37
- 6 -

User’s Manual of WNAP-6306
5.4.1 Wireless Setup............................................................................................................37
5.4.2 Multiple AP Setup........................................................................................................48
5.5 Wireless LED Thresholds ..................................................................................................49
5.6 LAN Setup............................................................................................................................50
5.6.1 LAN IP Address...........................................................................................................50
5.6.2 DHCP Server ..............................................................................................................51
5.6.3 DHCP Client Info.........................................................................................................52
5.7 Application & Game - UPnP............................................................................................... 52
5.8 Routing ................................................................................................................................52
5.9 System Management .......................................................................................................... 53
5.9.1 Password Setup..........................................................................................................53
5.9.2 Upgrade ......................................................................................................................54
5.9.3 Reboot.........................................................................................................................54
5.9.4 Backup ........................................................................................................................54
5.9.5 Restore........................................................................................................................55
5.9.6 WOL ............................................................................................................................55
5.9.7 System Time ...............................................................................................................56
Appendix A: FAQ.................................................................................................................................57
1. What and how to find my PC’s IP and MAC address? ....................................................57
2. What is Wireless LAN?.......................................................................................................57
3. What are ISM bands? .........................................................................................................57
4. How does wireless networking work?..............................................................................57
5. What is BSSID?................................................................................................................... 58
6. What is ESSID? ...................................................................................................................58
7. What are potential factors that may causes interference? ............................................58
8. What are the Open System and Shared Key authentications?......................................59
9. What is WEP?......................................................................................................................59
10. What is Fragment Threshold? ........................................................................................... 59
11. What is RTS (Request to Send) Threshold? ....................................................................60
12. What is Beacon Interval? ...................................................................................................60
13. What is Preamble Type?.....................................................................................................60
14. What is SSID Broadcast?...................................................................................................60
15. What is Wi-Fi Protected Access (WPA)? .......................................................................... 61
16. What is WPA2?.................................................................................................................... 61
17. What is 802.1x Authentication?.........................................................................................61
18. What is Temporal Key Integrity Protocol (TKIP)?............................................................61
19. What is Advanced Encryption Standard (AES)? .............................................................61
20. What is Inter-Access Point Protocol (IAPP)?...................................................................61
21. What is Wireless Distribution System (WDS)? ................................................................62
22. What is Universal Plug and Play (UPnP)?........................................................................62
- 7 -

User’s Manual of WNAP-6306
23. What is Maximum Transmission Unit (MTU) Size? .........................................................62
24. What is Clone MAC Address? ...........................................................................................62
25. What is DDNS?....................................................................................................................62
26. What is NTP Client?............................................................................................................62
27. What is VPN?....................................................................................................................... 62
28. What is IPSEC? ...................................................................................................................62
29. What is WLAN Block Relay between Clients? .................................................................63
30. What is WMM?.....................................................................................................................63
31. What is WLAN ACK TIMEOUT? .........................................................................................63
32. What is Modulation Coding Scheme (MCS)?...................................................................63
33. What is Frame Aggregation? ............................................................................................. 63
34. What is Guard Intervals (GI)? ............................................................................................63
Appendix B: Troubleshooting............................................................................................................64
Appendix C: Specifications................................................................................................................65
Appendix D: Glossary.........................................................................................................................67
- 8 -

User’s Manual of WNAP-6306
Chapter 1. Product Introduction
1.1 Package contents
The following items should be contained in the package:
WNAP-6306 Wireless Outdoor AP
18VDC PoE Injector (for EU/US region)
15VDC Power Adapter & PoE Injector (for UK/Other region)
Quick Installation Guide
CD-ROM (User’s Manual included)
If there is any item missed or damaged, please contact the seller immediately.
1.2 Product Description
The WNAP-6306 is an affordable IEEE 802.11b/g /n specifications of Outdoor AP solution. It provides a
setting of SOHO and enterprise standard for high performance, secure, manageable and reliable
WLAN. This document describes the steps required for the initial IP address assign and other
configuration of the Outdoor AP.
Flexible Outdoor Wireless Network
PLANET WNAP-6306 Wireless Outdoor Access Points brings users greatly more flexibility in
extending outdoor wireless coverage as it is designed to be easily attached to the antenna directly.
With built-in N-Type antenna connector, the WNAP-6306 can directly connect with various type and
high gain antenna* to cover wide range and deliver much farther wireless connection over 10Km.
Adopting IEEE 802.11n advanced 1T1R MIMO technology; the WNAP-6306 provides reliable wireless
network coverage and incredible improvement in the wireless performance. It can deliver data rate up
to 150Mbps, which is three times faster than normal 802.11g wireless devices.
- 9 -

User’s Manual of WNAP-6306
* Available antenna models for the WNAP-6306: ANT-OM8, ANT-OM15, ANT-FP9, ANT-FP18,
ANT-SE18, ANT-YG13, ANT-YG20, and ANT-GR21.
Easy Plug-n-Link
The WNAP-6306 especially benefits users to easily build outdoor wireless network with its Plug-n-Link
capability via the built in N-Type antenna connector. The N-Type antenna connector is most
commonly adapted with outdoor antenna and the mounting-free design of outdoor enclosure. Users
can directly plug the WNAP-6306 into the mounted antenna, and then the wireless link is constructed
immediately. Therefore, even users who never experience the wireless network installation can
accomplish the wireless deployment quickly.
- 10 -

User’s Manual of WNAP-6306
Multiple Operating & Wireless Modes
The WNAP-6306 supports multiple wireless communication connectivity (AP / Client CPE / WDS PtP /
WDS PtMP / Repeater / Universal Repeater), allowing various applications and giving users more
comprehensive experience. It also helps user to easily build wireless network and extend the wireless
range of existing wireless network.
Advanced Security and Management
In aspect of security, besides 64/128-bit WEP encryption, the WNAP-6306 integrates WPA / WPA2,
WPA-PSK and WPA2-PSK to protect your wireless LAN security. It provides wireless MAC filtering and
SSID broadcast control to consolidate the wireless network security and prevent unauthorized wireless
connection. Furthermore, the WNAP-6306 features the Dual-SSID function to enable you setup two
different wireless networks with the WNAP-6306 serving as a virtual access point for segmented
networks tailored to any office or industrial need.
Perfect Solution for Outdoor Environment
The WNAP-6306 is perfectly suitable to be installed in outdoor environments and exposed locations.
With its IP65 casing protection, the WNAP-6306 can perform stably under rigorous weather conditions
such as heavy rain and wind. The WNAP-6306 applies the proprietary Power over Ethernet (PoE)
design, so it can be easily installed in any area where power outlets are unavailable. It is the best way
using the WNAP-6306 to build outdoor wireless access applications between buildings on campuses,
businesses, rural areas and etc.
- 11 -

User’s Manual of WNAP-6306
1.3 Product Features
Industrial Compliant Wireless LAN & LAN
Compliant with IEEE 802.11n wireless technology capable of up to 150Mbps data rate
Backward compatible with 802.11b/g standard
Equipped with 10/100Mbps RJ-45 LAN Port, Auto MDI/ MDI-X supported
Support DHCP Server, UPnP
RF Interface Characteristics
Built-in N-Type Antenna Connector
High Output Power with multiple adjustable transmit power control
Outdoor Environmental Characteristics
IP65 Enclosure
Passive Power Over Ethernet Design
Operating Temperature: -20 ~ 70°C
Multiple Operation & Wireless Mode
Multiple Wireless Modes:
- AP, Client
- WDS PtP/PtMP
- Repeater
- Universal Repeater
Support Dual SSID
Secure Network Connection
Support Software Wi-Fi Protected Setup (WPS)
Advanced security: 64/128-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK(TKIP/AES)
Support MAC Filtering up to 20 clients
Easy Installation & Management
User friendly Web-based UI with On-line Help
System status monitoring includes DHCP Client, Associated List, System Log
Wireless LED Thresholds for antenna alignment
Wake-On-LAN(WOL) to allow remotely wake up a WOL enabled host
Mounting-free design
- 12 -

User’s Manual of WNAP-6306
1.4 Product Specification
Product WNAP-6306
2.4GHz 802.11n Wireless Outdoor Access Point
Hardware Specification
Standard support
IEEE 802.11b/g
IEEE 802.11n
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3x Flow Control
Memory 16 Mbytes DDR SDRAM
4 Mbytes Flash
Interface Wireless IEEE 802.11b/g/n
LAN: 1 x 10/100Base-TX, Auto-MDI/MDIX
Antenna Built-in N-Type (N-Male) Antenna Connector
Enclosure IP65 waterproof case
PoE Passive PoE 15~18V DC
LAN RJ-45 Pin Assignment: PIN 4,5(+), PIN 7,8(-)
Dimension (D x H) 46 x 205 mm
Weight 192g
Wireless Interface Specification
Frequency Band 2.4~2.4835GHz
Modulation
Transmission/Emission Type: DSSS / OFDM
Data modulation type: OFDM with BPSK, QPSK, 16-QAM, 64-QAM,
DBPSK, QPSK, CCK
Data Rate
802.11b: 11, 5.5, 2 and 1 Mbps with auto-rate fall back
802.11g: 54, 48, 36, 24, 18, 12, 9 and 6Mbps
802.11n (20MHz): up to 72Mbps
802.11n (40MHz): up to 150Mbps
Opt. Channel
America/ FCC: 2.414~2.462GHz (11 Channels)
Europe/ ETSI: 2.412~2.472GHz (13 Channels)
Japan/ TELEC: 2.412~2.484GHz (14 Channels)
RF Output Power
802.11b: 20 ± 1dBm
802.11g: 19 ± 1dBm
802.11n: 16 ± 1dBm
Receiver Sensitivity
802.11b: -84dBm
802.11g: -68dBm
802.11n (20MHz): -65dBm
802.11n (40MHz): -62dBm
Media Access Control CSMA/CA
- 13 -

User’s Manual of WNAP-6306
Output Power Control Range 1~100, default:100
Power Requirements 15~18V DC, 1A (switching)
Wireless Management Features
Wireless Mode
AP
Client
WDS PtP
WDS PtMP
WDS Repeater (AP+WDS)
Universal Repeater (AP+Client)
Channel Width 20MHz / 40MHz
Encryption Security
64/128-bits WEP
WPA, WPA-PSK
WPA2, WPA2-PSK
AP Isolation/WLAN Partition Able to isolate each connected wireless client from each other to
access mutually.
Wireless MAC address filtering
WPS (WiFi Protected Setup )
Wireless Security
Enable/Disable SSID Broadcast
B/G Protection Mode A protection mechanism prevents collisions among 802.11b/g modes
Association List Display current status of the wireless client associated with AP
Max. Wireless Client 25
Max. WDS AP 4
Software
Built-in DHCP server supporting static IP address distributing
LAN DHCP Reserve
Access Control MAC filtering up to 20 MAC address
Max. Wired Client 60
Applications & Game UPnP support
Management Web UI, DHCP Client, WOL
Diagnostic tool System Log
Environment & Certification
Operation Temperature: -20~70 Degree C
Humidity: 10~95% non-condensing
Storage Temperature: -30~80 Degree C
Humidity: 5~95% non-condensing
Regulatory CE / RoHS
- 14 -

User’s Manual of WNAP-6306
1.5 Wireless Performance
The following information will help you utilizing the wireless performance, and operating coverage of
WNAP-6306.
1. Site selection
To avoid interferences, please locate WNAP-6306 and wireless clients away from transformers,
microwave ovens, heavy-duty motors, refrigerators, fluorescent lights, and other industrial equipments.
Keep the number of walls, or ceilings between AP and clients as few as possible; otherwise the signal
strength may be seriously reduced. Place WNAP-6306 in open space or add additional WNAP-6306 as
needed to improve the coverage.
2. Environmental factors
The wireless network is easily affected by many environmental factors. Every environment is unique
with different obstacles, construction materials, weather, etc. It is hard to determine the exact operating
range of WNAP-6306 in a specific location without testing.
- 15 -

User’s Manual of WNAP-6306
Chapter 2. Hardware Description
2.1 LED Panel
Figure 2-1 Rear Panel LED Identification
2.2 LED Indications
LED State Meaning
On System On
Power Off System Off
On LAN Port linked.
Off No link.
LAN
Blinking Data is transmitting or receiving on the LAN interface.
LED1 On The wireless Signal Strength reaches the value
LED2 On The wireless Signal Strength reaches the value
LED3 On The wireless Signal Strength reaches the value
Signal Indicator
LED4 On The wireless Signal Strength reaches the value
- 16 -

User’s Manual of WNAP-6306
2.3 Port & Connector
Top View
Bottom View
N-Type (N- ale)M
oAntenna C nnector
Reset Button
LAN Port
Figure 2-2 Port and Connector of WNAP-6306
Interface Function
N-Type Connector For external antenna. You can use the N-Type connector to connect
with 2.4GHz external antenna.
LAN
The RJ-45 sockets allow LAN connection through Category 5 cables.
Support auto-sensing on 10/100M speed and half/ full duplex; comply
with IEEE 802.3/ 802.3u respectively.
Reset
Push continually the reset button of POE injector about 2 ~ 6 seconds
to reset the configuration parameters to factory defaults.
Please physically attach antenna before power on.
- 17 -

User’s Manual of WNAP-6306
2.4 PoE Injector
18VDC PoE Injector PoE Warning Label
※The 18VDC PoE Injector is for EU & US regions.
Figure 2-3 18VDC PoE Injector
15VDC Power Adapter & PoE Injector PoE Warning Label
※The 15VDC Power Adapter & PoE Injector are for UK & Other regions.
Figure 2-4 15VDC Power Adapter & PoE Injector
- 18 -

User’s Manual of WNAP-6306
Chapter 3. Hardware installation
This chapter describes safety precautions and product information you have to know and check before
installing WNAP-6306.
3.1 Preparation before Installation
3.1.1 Professional Installation Required
Please seek assistance from a professional installer who is well trained in the RF installation and
knowledgeable in the local regulations.
3.1.2 Safety Precautions
1. To keep you safe and install the hardware properly, please read and follow these safety
precautions.
2. If you are installing WNAP-6306 for the first time, for your safety as well as others’, please seek
assistance from a professional installer who has received safety training on the hazards
involved.
3. Keep safety as well as performance in mind when selecting your installation site, especially
where there are electric power and phone lines.
4. When installing WNAP-6306, please note the following things:
Do not use a metal ladder;
Do not work on a wet or windy day;
Wear shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket.
5. When the system is operational, avoid standing directly in front of it. Strong RF fields are present
when the transmitter is on.
3.1.3 Installation Precautions
1. Users MUST use a proper and well-installed surge arrestor and grounding kit with WNAP-6306;
otherwise, a random lightening could easily cause fatal damage to WNAP-6306. EMD (Lightning)
DAMAGE IS NOT COVERED UNDER WARRANTY.
2. Users MUST use the “AC Adapter & PoE Injector” shipped in the box with the WNAP-6306. Use of
other options will cause damage to the WNAP-6306.
3. Users MUST power off the WNAP-6306 first before connecting the antenna to it, otherwise,
damage might be caused to the WNAP-6306 itself.
4. The Antenna is required, and must be purchased separately.
5. No enclosure mounting is required, just the Antenna need to be mounted properly.
- 19 -

User’s Manual of WNAP-6306
OUTDOOR INSTALLATION WARNING
IMPORTANT SAFETY PRECAUTIONS:
LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with
the equipment you are installing.
CONTACTING POWER LINES CAN BE LETHAL. Make sure no power lines are anywhere where possible
contact can be made. Antennas, masts, towers, guy wires or
cables may lean or fall and contact these limes. People may be
injured or killed if they are touching or holding any part of
equipment when it contacts electric lines. Make sure there is
NO possibility that equipment or personnel can come in contact
directly or indirectly with power lines.
Assume all overhead lines are power lines.
The horizontal distance from a tower, mast or antenna to the nearest power line should be at least twice the total
length of the mast/antenna combination. This will ensure that the mast will not contact power if it falls either during
installation or later.
TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.
Select equipment locations that will allow safe, simple equipment installation.
Don’t work alone. A friend or co-worker can save your life if an accident happens.
Use approved non-conducting lasers and other safety equipment. Make sure all equipment is in good
repair.
If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.
If anything such as a wire or mast does come in contact with a power line, DON’T TOUCH IT OR
ATTEMPT TO MOVE IT. Instead, save your life by calling the power company.
Don’t attempt to erect antennas or towers on windy days.
MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES
CONNECTED TO ANTENNAS HAVE LIGHTNING ARRESTORS. This will help prevent fire damage or human
injury in case of lightning, static build-up, or short circuit within equipment connected to the antenna.
The base of the antenna mast or tower must be connected directly to the building protective ground or to
one or more approved grounding rods, using 1 OAWG ground wire and corrosion-resistant connectors.
Refer to the National Electrical Code for grounding details.
IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:
- 20 -