Plantronics 84100-01 User manual

LEARN
MORE
M100™Bluetooth®Headset
LEARN
MORE
Voyager™PRO+
Bluetooth®Headset

TAKE A GOOD LOOK
CALL BUTTON
• Takeacallorendit (1 tap)
• Redial(2 taps)
• Initiatephone’svoice-dialing
(2-second press until tone heard)
• Reconnectlostconnection (1 tap)
• Transferaudioto/fromheadset
(1-second press while on a call)
• DialPlantronicsVocalystTMvoice
andtextservice(3 taps) (Available
in U.S. only)
POWER BUTTON
• Onoroff(2-second press)
• Batterylevelvoicealerts(1 tap)
• Activatepairingafterinitialsetup
(press until LED flashes red/blue)
MICRO USB CHARGING PORT
• WithACcharger:
90 minutes for full charge
• Fullychargebeforerstuse
• Bestperformancewhenfullycharged
VOLUME/MUTE BUTTONS
• Volume:up/down(tap + or – buttons per
level change)
• Muteduringacall:on/off(1-second press
of both + and – buttons)
• Musicoraudio:pause/play(1-second
press of both + and – buttons)
LED
• Charging(solid red)
• Batterystatus(1-6 hrs left = 1 red flash,
low = 2 red flashes, critically low = 3 red
flashes)
• Missedcall(3 purple flashes, repeats for
5 minutes or until canceled by tapping
Call button)
• Pairingmode(repeating blue/red flashes)
• Multipoint (on = 2 blue flashes, off =
1 blue flash)
Besafe!Pleasereadthesafetyguidebefore
usingyournewheadset.

CONNECT TO YOUR PHONE
“Pairing” connects your
headset to your phone.
“Multipoint” lets you use
this headset with two phones.
Activate this feature before
pairing your second phone.
1. READY
Activate the Bluetooth feature on
your phone, then use the phone’s
settings to add/search/discover
new Bluetooth devices.
iPhone: Settings > General >
Bluetooth > On
(starts the search for devices)
BlackBerry®smartphone:
Settings/options >
Bluetooth: On >
Search for devices
VIDEO TUTORIAL IN USA:
www.plantronics.com/pairing
2. SET
FirstTime:
With headset turned off, activate
Bluetooth pairing mode by pressing
the Power button. The LED flashes
red/blue to indicate pairing mode.
ActivateMultipoint:
While pressing the Call button, turn
on the headset and keep pressing
the Call button until LED flashes
blue twice. (Repeat to deactivate.)
PairingSecondPhone/
ReconnectingOriginal:
Start in “OFF” mode. Press and
hold the Power button until the
LED flashes red/blue.
3. CONNECT
Select “VoyagerPRO+” from the
list of Bluetooth devices shown
on your phone.
If phone asks for a passcode, enter
four zeros (0000). You may see
**** on screen.
Some phones also ask to confirm
headset connection after pairing.
Headset LED will stop flashing red/
blue once your phone and headset
are successfully paired/connected.

MIX AND MATCH FOR BEST FIT
1
2
The headset comes with the medium eartip installed, but
you can replace it with the optional small or large eartip
provided.
RemovingtheEartip:
1. Grip the eartip and gently push it into the speaker
housing then rotate it a quarter turn to the left to
unlock.
2. Pull the eartip away from the headset.
AttachingaNewEartip:
1. Align the tabs on the eartip with the slots on the
speaker housing.
2. Gently push the eartip into housing while turning
it a quarter turn to the right. The eartip will stop
rotating when it is locked.
You may want to add the foam eartip covers
for additional comfort.
SoftGelEartips
(S,M,L)andFoam
EartipCovers
1
2

TRY IT ON
For the best sound clarity and comfort, make sure
you have a secure fit.
TheOver-and-InTechnique:
1. Guide the earloop behind your ear and position
the headset so that the speaker and eartip rest
comfortably in your ear.
2. Pivot the boom up or down to point the microphones
toward the corner of your mouth.
TheQuick-TurnAdjustment:
1. Pivot the boom into an upright position.
2. Rotate the boom and speaker to the other side
of the headset and lower it before fitting the headset
on your other ear.
1
22
1

MORE ABOUT MULTIPOINT
Plantronics VoyagerPRO+ supports
multipoint technology, which allows
you to use one headset with two
different Bluetooth mobile phones.
To pair your headset to a second
phone, see “Connect to Your Phone”.
How to Initiate a Call
When multipoint is on, the headset
initiates or redials a call from the
phone that last made an outgoing
call.
To use the second paired phone
instead, make the call using the
controls on that phone. The second
phone activates its link with the
headset.
NOTE: The headset cannot place a
current call on hold while answering
a call from the second phone.
How to Answer a Call While Talking
on the Other Paired Phone
To answer a second call on the
other phone, the current call must
be terminated or transferred back
to the first phone. To transfer the call,
see “Take a Good Look”.
If you choose not to answer, the
second call will go to voice mail.
Answeringanincomingcallfrom
thesecondphone,whilealreadyon
anothercall:
1. To answer the second call, end the
first call by tapping the Call button.
2. Answer the second call by tapping
the Call button again.
TIP: To avoid issues with multipoint,
use the Call button on the headset
rather than your phone controls.

LISTEN TO THE VOICE
WHAT YOU’LL HEAR WHEN YOU’LL HEAR IT
PowerOn After pressing the Power button for 2 seconds
PowerOff After pressing the Power button for 2 seconds
TalkTime:(“6hrs”,“5hrs”,“4hrs”,
“3hrs”,“lessthan2hrs”)
After powering the headset “on”
BatteryLow When you have under 30 minutes left before the
battery must be recharged
RechargeHeadset When you have approximately 10 minutes left before
the battery must be recharged
Connected After turning the headset on or reconnecting a dropped
Bluetooth signal
Phone1Connected After powering the headset to “on” or reconnecting a
dropped Bluetooth connection
Phone2Connected After pairing a second phone using multipoint feature
Pairing While the headset and phone are trying to pair/connect
PairingSuccessful After the headset and phone are successfully paired/
connected
PairingIncomplete,RestartHeadset After the headset and phone tried to pair but failed
MuteOn After pressing the Volume + and - buttons simultane-
ously during a call
MuteOff When on mute, after pressing the Volume + and -
buttons simultaneously during a call
LostConnection When the phone loses the Bluetooth connection with
the headset
VolumeMaximum When the highest volume level is reach after tapping
Volume + button
VolumeMinimum When the lowest volume level is reached after tapping
Volume - button
This headset announces various
status alerts when you power
on/off, run low on talk time, or
lose/reconnect the Bluetooth
connection to your phone.

TIPS
Stream Music and More:
Once your phone is connected, music
or audio files like GPS directions or
podcasts can be streamed through
the headset.
The headset supports A2DP when
connected to a device capable of
streaming A2DP audio.
PAUSE/PLAY: You can pause and play
music and audio files using controls
on the headset if your device also
supports Bluetooth AVRCP. Simply
press both volume +/- buttons simul-
taneously until you hear a beep.
Use Multipoint One Call at a Time:
You cannot place a current call on
hold while answering a call from the
second phone.
Tap the Call button to end the first
call and tap it again to take the
second call.
Check Headset Battery Level
on an iPhone:
The battery level of your headset is
shown on-screen beside the phone’s
battery level icon.
Check the Battery Level:
The battery alert announces remaining
talk time after calls end.
In addition, you can tap the Power
button to check battery level.
Know How to Reconnect:
Your headset tries to reconnect a lost
connection. If it can’t, then tap the Call
button once or manually reconnect via
the phone’s Bluetooth device menu.
Stay Near Your Phone:
Bluetooth has a working “range” of
up to 33 feet between the phone and
headset before audio degrades and
the connection is lost.

SPECIFICATIONS
TalkTime Up to 6 hours talk time
StandbyTime Up to 5 days standby
OperatingDistance(Range) Up to 33 foot range
HeadsetWeight 17 grams
ChargeConnector Micro USB cable with micro USB connection and
AC/DC 100–240V
BatteryType Rechargeable, non-replaceable Lithum-ion polymer
ChargeTime(Maximum) 1.5 hours
PowerRequirements 5V DC - 180mA
BluetoothVersion Version 2.1 + Enhanced Data Rate (EDR), eSCO data
packet transfer, Secure Simple Pairing (SSP) if supported
by phone
BluetoothProles Hands-free v1.5 (HFP), Headset v1.1 (HSP), Advanced
Audio Distribution (A2DP) and Audio/Video Remote
Control (AVRCP)
Operating,Storageand
ChargingTemperature
32°F - 104°F (0 - 40°C)

LEARN
MORE
M100™Bluetooth®Headset
NEED MORE HELP?
24-hour support in USA:
1-866-363-BLUE (2583)
1-year limited warranty details:
www.plantronics.com/warranty
© 2010 Plantronics, Inc. All Rights Reserved. Plantronics, Vocalyst and
Voyager Pro+ are trademarks or registered trademarks of Plantronics, Inc.
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc.
and any use of such marks by Plantronics, Inc. is under license. iPhone
is a trademark of Apple Inc. registered in the U.S. and other countries.
Blackberry is owned by Research In Motion Limited and is registered in
the United States and may be pending or registered in other countries.
Plantronics, Inc is not endorsed, sponsored, affiliated with or otherwise
authorized by Research In Motion Limited.
Patents US 5,210,791; D612,840; D612,834; D612,835; BR DI69022011;
China ZL200930191189.7; EM 001142582-001; IN 223437; Taiwan
D134706; Patents Pending. 84470-01
Z109
N10687