Plantronics Poly Calisto 5300 User manual

Calisto 5300
Speakerphone
User Guide
PLANTRONICS + POLYCOM. NOW TOGETHER AS

Contents
Controls and status lights 3
Setup 4
Mobile setup 4
Corded setup 4
USB adapter setup (BT600 models only) 4
Load software 5
Charge 6
Check battery status 6
Charge 6
Daily Use 7
Power 7
Answer or End a call 7
Place a call on hold 7
Mute/Unmute 7
Volume 7
Support 8
2

A corded, portable speakerphone with mobile connectivity.
BT600 models only
Icon LEDs Function
Volume buttons Sequential white lights Volume increase/decrease
Mute button
LED Solid white Power on
Solid red Microphone muted
Call button Flashing green Incoming call
Solid red In a call
Kensington lock port
Power/ Red/blue flashes Battery status
Bluetooth switch Red/blue flashes Bluetooth pair mode
Bluetooth button Red/blue flashes Bluetooth USB adapter pair mode
Controls and status lights
3

1To pair your mobile device with your speakerphone, slide the Power switch towards the Bluetooth
icon to the right for 2 seconds. You hear "pairing" and the LED next to the Bluetooth icon flashes
red and blue.
2Activate Bluetooth on your phone and set it to search new devices, select Poly CL5300 Series.
3Pairing is successful when you hear "pairing successful" and the LED goes out.
Connect the USB cable from the USB port on the speakerphone to the USB port on your computer.
Your Bluetooth USB adapter comes pre-paired to your speakerphone.
1Turn on your speakerphone and insert the Bluetooth USB adapter into your computer.
2Pairing is successful when you hear "pairing successful" and the USB adapter turns solid blue.
NOTE Adapter design may vary.
Pair USB adapter again
Your USB adapter is pre-paired to your speakerphone. In the event that your adapter is
disconnected or bought separately, manually pair the adapter to your headset.
1Insert the Bluetooth USB adapter into your laptop or computer and wait for your computer to
recognize it.
2Put your speakerphone in pair mode by sliding the Power switch towards the Bluetooth icon to the
right for 2 seconds. You hear "pairing" and the LED next to the Bluetooth icon flashes red and blue.
3Put your adapter into pair mode by pressing and holding the recessed pair button with a pen or
paperclip until the adapter flashes red and blue.
NOTE Adapter design may vary
Pairing is successful when you hear "pairing successful; PC connected" and the adapter LED turns
solid blue.
Setup
Mobile setup
Corded setup
USB adapter setup
(BT600 models only)
4

Download Plantronics Hub for Windows and Mac by visiting plantronics.com/software. This allows
you to customize your device behavior through advanced settings and options.
Load software
5

To check the battery status of your speakerphone, slide the power button to the right and release.
Charge the speakerphone via USB using your computer or a USB AC adapter (not provided). The
Power switch LED flashes while charging and turns off when fully charged. Allow 3.5 hours for a
full charge.
Charge
Check battery status
Charge
6

Slide the Power button to the right to power on. The speakerphone LED illuminates white and you
hear "power on."
A short press of the Call button answers or ends a call.
To place a call on hold, press the Call button for 2 seconds.
A short press of the Mute button mutes or unmutes the microphones.
Press the up (+) or down (-) volume buttons for the desired volume.
Daily Use
Power
Answer or End a call
Place a call on hold
Mute/Unmute
Volume
7

Support
NEED MORE HELP?
plantronics.com/support
Plantronics, Inc. Plantronics B.V.
345 Encinal Street
Santa Cruz, CA 95060
United States
Scorpius 171
2132 LR Hoofddorp
Netherlands
©2020 Plantronics, Inc. All rights reserved. Poly, the propeller design, and the Poly logo are
trademarks of Plantronics, Inc. All other trademarks are the property of their respective owners.
216075-06 02.20
8