Playcraft Cross Loop Climber R3.5 User manual

IMPORTANT NOTES: Read First
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
CROSS LOOP CLIMBER
Rev D
12/2/2009
R3.5-1229
Page 1 of 3
NOTE: 5' deck height shown.
The Handbook for Public Playground Safety, Publication #325 at www.CPSC.gov for the surfacing appropriate
for the fall height of the equipment or consult you surfacing supply representative.
(A) Use liquid thread lock (such as Loctite
®
) with all threaded hardware. Important: Liquid thread lock (prior to
curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving as a
lubricant during assembly.
(B) Do not pour concrete until the equipment is completely assembled, leveled and plumbed. Concrete must be
allowed to cure completely before using the equipment (at least 72 hours).
(C) Use appropriate compliant protective surfacing and adjust footing depths accordingly. See free publication -
FIGURE 1
Cross Loop Climber
See Footing Detail
Figure 1.1

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
CROSS LOOP CLIMBER
Rev D
12/2/2009
R3.5-1229
Page 2 of 3
24
34
"
628mm
See Section 06.1 of the Installation Manual
Footing Detail
Step 1
Refer to Footing Layout and mark footing hole location.
Dig (1) Ø 12" footing hole. Refer to Footing Detail for
depth and details.
IMPORTANT: For areas with soft soil conditions, larger
footings may be required.
* Footing depth must be adjusted to compensate for the
depth/thickness requirements of selected safety surfacing.
Top View - Footing Layout
Pea Gravel (for drainage)
Concrete Footing
Optional Filter Fabric over
(welded 5/8" rod)
2b Stone, Drain Rock
Undisturbed Soil
Footing Anchor
Installers Manual
Blocking, see
(Finish Grade)
Compacted depth shown. (See Note C)
9" compacted or 12" uncompressed depth
Impact attenuating (resilient) surfacing
LOOSE FILL GROUND COVER:
(Top of Soil)
18"
457mm 686mm *27"
12"
305mm

Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
CROSS LOOP CLIMBER
Rev D
12/2/2009
R3.5-1229
Page 3 of 3
Specifications Parts List
Part #
DESCRIPTION QTY
Varies Cross Loop Climber R3.5 1
9103062-TR Bolt Button Head 3/8" x 1-1/4" 2
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 4
9413002 Nut Lock 3/8" 2
Plumb and level entire component. Pour concrete
into footing hole. Allow at least 72 hours to cure
before using this equipment. (See Note B)
Step 5
Place appropriate compliant protective surfacing
under and around Cross Loop Climber.
(See Note C)
Step 2
Place Cross Loop Climber into footing hole and
attach to Deck as shown in Figure 1.1. (See Note A)
Step 3
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE"
section of the Installation Manual.
Step 4
CROSS LOOP CLIMBER:
Shall be constructed of 1.660" O.D. 11 gauge steel
tubing with welded 1.315" O.D. 12 gauge steel tube
handles, rungs, and 3/16" thick steel mounting
plate. The Snake Climber has a multi-stage baked
on powder coat finish.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
Maintenance Manual.
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance
3/8" x 1-1/4"
3/8" Lock Nut
Figure 1.1
Button Head Bolt
3/8" x 1" O.D. Washer
3/8" x 1" O.D. Washer
CROSS LOOP
CLIMBER