Playcraft Slide Sit Down Hood R5-1303 User manual

IMPORTANT NOTES: Read First
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
SLIDE SIT DOWN HOOD
Rev A
10/10/2009
R5-1303
Page 1 of 3
(A) Use liquid thread lock (such as Loctite
®
) with all threaded hardware. Important: Liquid thread lock (prior to
curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving as a
lubricant during assembly.
(B) Refer to Installation Manual for R5-09 Collars and R5-11 Socket Clamps assembly instructions.
and R5-11 Socket Clamps
Figure 1.1
See installation Manual
Sections R5-09 Collars
Figure 1.2
FIGURE 1
Slide Sit Down Hood

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
SLIDE SIT DOWN HOOD
Rev A
10/10/2009
R5-1303
Page 2 of 3
Step 1
(Factory Assembled)
Attach Sit Down Hood Guards to the Slide Hood as
shown in Figure 2.
Figure 1.1
Step 2
Locate and attach collars at the height shown in Front
Elevation (See Note B).
* Height shown from top of deck to top of collar.
Step 3
Insert the bottom tabs of Slide Sit Down Hood into the
slots of Deck and attach Slide Sit Down Hood to collars
as shown in Figure 1.1. (See Note B)
FRONT ELEVATION
39" *
991mm
1/4" x 1" OD
Fender Washer
SLIDE HOOD R5
GAURD
1/4"x 1-1/4" BH TR
Tek Screw
FIGURE 2
TOP
BOTTOM
SOCKET CLAMP
SOCKET CLAMP
SLIDE HOOD R5

Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
SLIDE SIT DOWN HOOD
Rev A
10/10/2009
R5-1303
Page 3 of 3
Assembled Parts List
Specifications
Parts List
SLIDE SIT DOWN HOOD:
Shall be constructed of UV-stabilized, rotationally
molded, linear, low density polyethylene with an
average wall thickness of .250".
SIT DOWN HOOD - TOP RAIL:
Shall be constructed of 1.315" O.D. 12 gauge steel
tubing. Sit Down Hood - Top Rail shall have a multi-
stage baked-on powder coat finish.
SIT DOWN HOOD GUARD SINGLE:
Shall be constructed of 1.315" O.D. 12 gauge and
1.029" O.D. 14 gauge steel tubing. Sit Down Hood
Guard shall have a multi-stage baked-on powder coat
finish.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
Figure 1.2
Step 4
Attach Slide Sit Down Hood to Deck as
shown in Figure 1.2. (See Note A)
Step 5
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE"
section of the Installation Manual.
Part # DESCRIPTION QTY.
HS-1001-R5 Socket Clamp Set R5 2
9103062-TR Bolt Button Head 3/8" x 1-1/4" 2
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 4
9413002 Nut Lock 3/8" 2
Part # DESCRIPTION QTY.
DF-4827 Slide Hood R5 1
FS-1303-R5 Sit Down Hood Guard 2
LF-0009 Sit Down Hood - Top Rail 1
9271062-TR Screw Tek 1/4" x 1-1/4" BH TR 7
9321052-THK Washer Fender 1/4" x 1" OD x .125" thk 7
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Maintenance
3/8" x 1"
3/8" Lock Nut
O.D. Washer
O.D. Washer
3/8" x 1"
3/8" x 1-1/4"
Button Head Bolt