Playcraft 36" Single Slide 1701-3 User manual

IMPORTANT NOTES: Read First
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
36" SINGLE SLIDE
Rev D
7/18/2009
1701-3
Page 1 of 4
Figure 1.2
See Footing Detail
R3.5-1304 Slide Sit Down Wall
See Installation Manual Section
R5-1304 Slide Sit Down Wall or
Figure 1.1
NOTE: R5 Configuration shown.
R3.5 will vary slightly, but does
not affect the assembly.
(E) Slide exit height shall be no greater than 11". Exit region must also have a downward slope of 0 to 4°.
(A) Use liquid thread lock (such as Loctite
®
) with all threaded hardware. Important: Liquid thread lock (prior to
curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving as a
lubricant during assembly.
(B) Do not pour concrete until the equipment is completely assembled, leveled and plumbed. Concrete must be
allowed to cure completely before using the equipment (at least 72 hours).
(C) Refer to Installation Manual for R5-1304 Slide Sit Down Wall or R3.5-1304 Sit Down Wall assembly
instructions.
(D) Use appropriate compliant protective surfacing and adjust footing depths accordingly. See free publication -
The Handbook for Public Playground Safety, Publication #325 at www.CPSC.gov for the surfacing appropriate
for the fall height of the equipment or consult you surfacing supply representative.
FIGURE 1
36" Single Slide

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
36" SINGLE SLIDE
Rev D
7/18/2009
1701-3
Page 2 of 4
24"
610mm
12"
305mm
Installers Manual
Blocking, See
Footing Detail
(Top of Soil)
Pea Gravel (for drainage)
Concrete Footing
Optional Filter Fabric Over
(welded 5/8" Rod)
2b Stone, drain rock
Undisturbed Soil
Footing Anchor
(Finish Grade)
LOOSE FILL GROUND COVER:
Impact attenuating (resilient) surfacing
9" compacted or 12" uncompressed depth
Compacted depth shown. (See Note D)
34" *
864mm
25" **
635mm
Note E
For Exit
Height See
55
1116
"
1414mm
Step 1
Refer to Footing Layout and mark footing hole locations.
Dig (1) 12" x 24" oblong footing hole. Refer to Footing
Detail for depth and details.
IMPORTANT: For areas with soft soil conditions, larger
footings may be required.
* Footing depth must be adjusted to compensate for
the depth/thickness requirements of selected safety
surfacing. See Section 06.1 of the Installation Manual
** Adjust footing depth with blocking to meet required
exit height. (See Note E)
Top View - Footing Layout

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
36" SINGLE SLIDE
Rev D
7/18/2009
1701-3
Page 3 of 4
3/8" Lock
Deck
Button Head Bolt
3/8" x 1-3/4"
Nut
3/8" x 1" O.D.
Washer
36" SINGLE
SLIDE
Figure 1.2
Step 5
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE"
section of the Installation Manual.
Step 6
Plumb and level entire component. Pour concrete
into footing hole. Allow at least 72 hours to cure
before using this equipment. (See Note B and E)
Step 7
Place appropriate compliant protective surfacing
under and around 36" Single Slide. (See Note D)
Step 2
Attach the Slide Sit Down Wall to the deck and posts.
(See Note C)
Step 3
Attach the Single Slide Leg to the 36" Single Slide as
shown in Figure 1.1. (See Note A)
Step 4
Place the 36" Single Slide in the footing hole and attach
to the deck as shown in Figure 1.2. (See Note A)
3/8" x 1" O.D.
SLIDE
36" SINGLE
SLIDE LEG
SINGLE
Washer
3/8 x 3/4"
Hex Bolt
Figure 1.1

Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
36" SINGLE SLIDE
Rev D
7/18/2009
1701-3
Page 4 of 4
Specifications
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Maintenance
Parts List
36" SINGLE SLIDE:
Shall be constructed of UV-stabilized, rotationally
molded, linear, low density polyethylene with an
average wall thickness of .250".
SINGLE SLIDE LEG:
Shall be fabricated of 1.660" O.D. 11 gauge steel
tubing welded onto a 10 gauge steel plate. The
Single Slide Leg has a multi-stage baked-on
powder coat finish.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
Part # DESCRIPTION QTY.
DE-4399 36" Single Slide 1
FS-1701 Single Slide Leg 1
9103082-TR Bolt Button Head 3/8" x 1-3/4" 4
9123032 Bolt Hex 3/8" x 3/4" 4
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 12
9413002 Nut Lock 3/8" 4