Playcraft 1249-DDH User manual

IMPORTANT NOTES: Read First
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
GEO-WAVE CLIMBER HORIZONTAL
INSTALLATION INSTRUCTIONS
Rev D
10/7/2020
1249-DDH/DGH
Page 1 of 5
Figures 1.1 and 1.3
See Footing Detail
See Installation Manual
Section 1309 Half Wall
Figures 1.2 & 1.4
(A) Use liquid thread lock (such as Loctite
®
) with all threaded hardware. Important: Liquid thread lock (prior to
curing helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving as a
lubricant during assembly.
(B) Do not pour concrete until the equipment is completely assembled, leveled and plumbed. Concrete must be
allowed to cure completely before using the equipment (at least 72 hours).
(C) Refer to Installation Manual for 1 309 Half Wall assembly instructions.
(D) Use appropriate compliant protective surfacing and adjust footing depths accordingly. See free publication -
The Handbook for Public Playground Safety, Publication #325 at www.CPSC.gov for the surfacing appropriate
for the fall height of the equipment or consult your surfacing supply representative.
NOTE : R5 4' deck height ground mount shown.
Other configurations will vary slightly but does
not affect assembly.
FIGURE 1
Geo-Wave Climber Horizontal
Deck to Ground Mount

www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
GEO-WAVE CLIMBER HORIZONTAL
INSTALLATION INSTRUCTIONS
Rev D
10/7/2020
1249-DDH/DGH
Page 2 of 5
27" * 686mm
12" 305mm
18" 457mm
Optional Filter Fabric Over
Pea Gravel (for drainage)
Concrete Footing
Footing Anchor
Blocking, See
Installers Manual
2b Stone, drain rock
Undisturbed Soil
(Top of Soil)
(Finish Grade)
LOOSE FILL SURFACING
MATERIAL SHOWN:
9" compressed or 12"
uncompressed depth.
Compressed depth shown.
(See Note D)
24" 610mm
Max. deck height
difference
60" 1524mm Max.
24" [610mm] Min.
Deck to Finish Grade
(Finish Grade)
(See Table)
X
28" 712mm
9 15/16" 252mm
Footing Detail
SIDE ELEVATION
Deck to Deck Mount
SIDE ELEVATION
Deck to Ground Mount
Top View - Footing Layout
Step 1
For Deck to Ground Mount Only
Refer to Footing Layout and mark footing hole locations.3
Dig 2 Ø 12" footing holes. Refer to Footing Detail for depth and
details.
IMPORTANT: For areas with soft soil conditions, larger
footings may be required.
* Footing depth must be adjusted to compensate for the
depth/thickness requirements of selected safety surfacing.
See Section 06.1 of the Installation Manual.
Footing Distance Table
Center of Post to Center of Footing
Deck Height
X (in.) X (mm)
24" 69-7/8 1774
30" 68-1/8 1730
36" 65-3/4 1670
42" 62-11/16 1592
48" 58-13/16 1495
54" 54 1372
60" 47-7/8 1216

www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
GEO-WAVE CLIMBER HORIZONTAL
INSTALLATION INSTRUCTIONS
Rev D
10/7/2020
1249-DDH/DGH
Page 3 of 5
#10 Pan Head
Screw
VENT PLUG
GEO-WAVE CLIMBER
Figure 1.1
3/8" Lock Nut
3/8" x 1" O.D.
Washer
3/8" x 1" O.D.
Washer
3/8" x 1-1/4"
Button Head Bolt
DECK MOUNT
BRACKET
Figure 1.2
DECK MOUNT
BRACKET
HORIZONTAL GEO-WAVE
DECK FILLER
3/8" Lock Nut
3/8" x 1" O.D.
Washer
3/8" x 1" O.D.
Washer
3/8" x 1-1/2"
Button Head Bolt
FIGURE 2
Step 2
(Factory Assembled)
Plug vent holes at each end using the Vent Plugs
as shown in Figure 1.1.
Step 3
Attach Half Walls to decks. (See Note C)
Step 4
Attach Deck Mount Brackets to deck as shown in
Figure 1.2. (See Note A)
Step 5
(For JPFA Only)
Attach Deck Mount Brackets and Horizantal
Geo-Wave Deck Filler to deck as shown in
Figure 2. (See Note A)

www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
GEO-WAVE CLIMBER HORIZONTAL
INSTALLATION INSTRUCTIONS
Rev D
10/7/2020
1249-DDH/DGH
Page 4 of 5
1/2" x 1-1/2"
Button Head Bolt
1/2" x 1-3/8" O.D.
Washer
CLIMBER LEG
GEO-WAVE
CLIMBER
Figure 1.3
1/2" x 1-1/2"
Button Head Bolt
1/2" x 1-3/8" O.D.
Washer
GEO-WAVE
CLIMBER
DECK MOUNT
BRACKET
Figure 1.4
Step 6
For Deck to Ground Mount Only
Attach Geo-Wave Climber Legs to Geo-Wave Climber
as shown in Figure 1.3. Place Geo-Wave Climber
Legs into footing holes. (See Notes A & B)
Step 7
Attach Geo-Wave Climber to Deck Mount Brackets
as shown in Figure 1.4. (See Note A)
Step 8
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE"
section of the Installation Manual.
Step 9
Plumb and level entire component. Pour concrete
into footing holes. Allow at least 72 hours to cure
before using this equipment. (See Note B)
Step 10
Place appropriate compliant protective surfacing
under and around Geo-Wave Climber. (See Note D)

www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
GEO-WAVE CLIMBER HORIZONTAL
INSTALLATION INSTRUCTIONS
Rev D
10/7/2020
1249-DDH/DGH
Page 5 of 5
GEO-WAVE CLIMBER:
Shall be constructed of UV-stabilized, rotationally
molded, linear low density polyethylene with an
average double wall thickness of .250".
GEO-WAVE DECK MOUNT BRACKET:
Shall be formed from 1/4" thick sheet steel and will
have a multi-stage baked-on powder coat finish.
GEO-WAVE CLIMBER LEG:
Shall be fabricated using 1.029" O.D. 14 Gauge
steel tubing with formed 1/4" thick end tab and will
have a multi-stage baked-on powder coating.
DECK FILLER:
Shall be made from high density 3/4" sheet plastic
specially formulated for optimum UV stability and
color retention.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
DECK TO DECK MOUNT
Part # DESCRIPTION QTY
BE-4820 Geo-Wave Deck Mount Bracket 4
9103062-TR Bolt Button Head 3/8" x 1-1/4" 8
9105072 Bolt Button Head 1/2" x 1-1/2" 4
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 16
9335062-5 Washer Flat 1/2" x 1-3/8" OD 4
9413002 Nut Lock 3/8" 8
DECK TO GROUND MOUNT
Part # DESCRIPTION QTY
BE-4820 Geo-Wave Deck Mount Bracket 2
FS-1249-DGH Geo-Wave Climber Deck-Ground-Horizontal Leg 2
9103062-TR Bolt Button Head 3/8" x 1-1/4" 4
9105072 Bolt Button Head 1/2" x 1-1/2" 4
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 8
9335062-5 Washer Flat 1/2" x 1-3/8" OD 4
9413002 Nut Lock 3/8" 4
Part # DESCRIPTION QTY
DE-4807 Geo-Wave Climber Horizontal 1
EE-4867 Geo-Wave Vent Plug 2
9251032 Screw SQ #10x3/4 DR PH SMS SS 6
DECK TO GROUND MOUNT
JAPAN
Part #
DESCRIPTION QTY
BE-4820 Geo-Wave Deck Mount Bracket
2
EE-0656 Horizontal Geo-Wave Deck Filler
1
FS-1249-DGH
Geo-Wave Climber Deck-Ground-Horizontal
Leg
2
9103072-TR Bolt Button Head 3/8" x 1-1/2"
4
9105072 Bolt Button Head 1/2" x 1-1/2"
4
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick
8
9335062-5 Washer Flat 1/2" x 1-3/8" OD
4
9413002 Nut Lock 3/8"
4
Parts List Specifications
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Maintenance
Assembled Parts List