Playcraft SUNRISE CLIMBER R5 User manual

IMPORTANT NOTES: Read First
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
SUNRISE CLIMBER R5
INSTALLATION INSTRUCTIONS
Rev B
6/8/2020
R5-12801
Page 1 of 3
See Installation Manual Section
09 Collars
See Installation Manual Section
R5-1314 Access Wall
See Installation Manual Section
1313 Curved Post Handle
Figure 1.1
(A) Use liquid thread lock (such as Loctite
®) with all threaded hardware.
Important: Liquid thread lock (prior
to curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving
as a lubricant during assembly.
(B) Refer to Installation Manual for 09 Collars, 1313 Curved Post Handle, and R5-1314 Access Wall
installation instructions.
(C) An appropriate energy absorbing safety surface is required under and around all playground equipment.
Loose fill protective surfacing is shown only as an example for the purpose of this assembly instruction. Other
surfacing material may vary in thickness and/or compression depths. See free publication - The Handbook for
Public Playground Safety, Publication #325 at www.cpsc.gov for the surfacing appropriate for the fall height
of the equipment or consult your surfacing supply representative.
NOTE : R5 5' deck height Sunrise Climber right
side shown. Other configurations will vary
slightly, but does not affect assembly.
FIGURE 1
Sunrise Climber

www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
R5-12801
Page 2 of 3
Rev B
6/8/2020
SUNRISE CLIMBER R5
INSTALLATION INSTRUCTIONS
177
16
"
443mm
***
381
8
"
968mm
**
41
2
"
114mm
*
24"
610mm
**
Elevation View
(Finish Grade)
3/8" Lock Nut
3/8" x 1" O.D. Washer
3/8" x 1" O.D. Washer
3/8" x 1-1/4"
Button Head Bolt
Step 2
Attach Sunrise Climber to deck as shown in Figure 2.
(See Note A).
SUNRISE
CLIMBER
MOUNTING
BLOCK TOP
MOUNTING
BLOCK BOTTOM
1/4" x 1-3/8" Socket
Head Screw
3/8" x 2-1/2"
Shoulder Bolt
SUNRISE CLIMBER
1/2" SAE Washer
3/8" x 2" Barrel
Nut
Figure 1.1
FIGURE 2
Step 1
Locate and attach collars at heights shown in
Elevation View. (See Note B)
* Height from top of deck to top of collar.
** Height shown from top of collar to top of collar.
*** Height shown from finish grade to top of collar.
Step 3
Attach Sunrise Climber to collars as shown in
Figure 1.1. (See Note A).
Step 4
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE"
section of the Installation Manual.
Step 5
Place required protective surfacing under and
around Sunrise Climber. (See Note C)

www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
SUNRISE CLIMBER R5
INSTALLATION INSTRUCTIONS
Rev B
6/8/2020
R5-12801
Page 3 of 3
SUNRISE CLIMBER R5:
Shall be fabricated using 1.315" O.D. 12 guage steel
rungswith welded 1.900" O.D. 11 guage steel frame,
1/4" thick steel mounting plate and clevises and will
have a multi-stage baked-on powder coat finish.
MOUNTING BLOCKS:
Shall be two-part and precision die-cast from a high
strength aluminum alloy and will have a multi-stage
baked-on powder coat finish.
SOCKET CLAMPS:
Shall be two-part and precision die-cast from a high
strength aluminum alloy and will have a multi-stage
baked-on powder coat finish.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
Part #
DESCRIPTION QTY
FS-12801-R5 Sunrise Climber R5
1
GF-7006-B Mounting Block R5 Bottom
2
GF-7006-T Mounting Block R5 Top
2
9103062-TR Bolt Button Head 3/8" x 1-1/4"
4
9143112-TR Bolt Shoulder 3/8" x 2-1/2" BH
2
9281062-5-TR Screw Soc HD 1/4" x 1-3/8"
2
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick
8
9345002 Washer Flat SAE 1/2"
4
9413002 Nut Lock 3/8"
4
9443092-TR Nut Barrel 3/8" x 2" BH
2
Parts List Specifications
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Maintenance