Playcraft 1210 User manual

IMPORTANT NOTES: Read First
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
VERTICAL LADDER
INSTALLATION INSTRUCTIONS
Rev E
4/4/2013
1210
Page 1 of 3
NOTE: R5 5' Vertical Ladder shown.
Other configurations will vary slightly,
but does not affect assembly.
Public Playground Safety, Publication #325 at www.cpsc.gov for the surfacing appropriate for the fall height of
the equipment or consult your surfacing supply representative.
(A) Use liquid thread lock (such as Loctite
®
) with all threaded hardware. Important: Liquid thread lock (prior to
curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving as a
lubricant during assembly.
(B) Do not pour concrete until the equipment is completely assembled, leveled and plumbed. Concrete must be
allowed to cure completely before using the equipment (at least 72 hours).
(C) Refer to Installation Manual for 1309 Half Wall installation instructions.
(D) An appropriate energy absorbing safety surface is required under and around all playground equipment.
Loose fill protective surfacing is shown only as an example for the purpose of this assembly instruction. Other
surfacing material may vary in thickness and/or compression depths. See free publication - The Handbook for
FIGURE 1
Vertical Ladder
See Footing Detail
Section 1309 Half Wall
See Installation Manual
Figure 1.1

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
VERTICAL LADDER
INSTALLATION INSTRUCTIONS
Rev E
4/4/2013
1210
Page 2 of 3
2b Stone, drain rock
Concrete Footing
Blocking, see
Pea Gravel (for drainage)
Undisturbed Soil
Optional Filter Fabric over
Installers Manual
LOOSE FILL SURFACING MATERIAL SHOWN:
9" compressed or 12" uncompressed depth.
Compressed depth shown. (See Note D)
(Finish Grade)
(Top of Soil)
Footing Anchor
*
686mm
18"
457mm
27"
12"
305mm
9
1316
"
249mm
4
316
"
107mm
See Section 06.1 of the Installation Manual.
Footing Detail Step 1
Refer to Footing Layout and mark footing hole locations.
Dig (2) Ø 12" footing holes. Refer to Footing Detail for
depth and details.
IMPORTANT: For areas with soft soil conditions, larger
footings may be required. Additionally, half foot deck
heights will require 6" deeper footing holes.
* Footing depth must be adjusted to compensate for the
depth/thickness requirements of selected safety surfacing.
Top View - Footing Layout

Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
VERTICAL LADDER
INSTALLATION INSTRUCTIONS
Rev E
4/4/2013
1210
Page 3 of 3
Place required protective surfacing under and around
Specifications
Fully tighten all fasteners according to the
Step 3
Parts List
Step 4
section of the Installation Manual.
Vertical Ladder. (See Note D)
Step 5
using this equipment. (See Note B)
footing holes. Allow at least 72 hours to cure before
(See Notes A & C)
"TIGHTENING TORQUE FOR HARDWARE"
Plumb and level entire component. Pour concrete into
Step 2
Attach Half Walls to Deck. Place Vertical Ladder into
footing holes and attach to deck as shown in Figure 1.1.
Part #
DESCRIPTION QTY.
Varies Vertical Ladder 1
9103062-TR Bolt Button Head 3/8" x 1-1/4" 2
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 4
9413002 Nut Lock 3/8" 2
Figure 1.1
VERTICAL LADDER:
Shall be fabricated using 1.315" O.D. 12 gauge steel
tubing with welded 1.315" O.D. 12 gauge steel rungs
and 1/4" thick steel mounting plate. The Vertical
Ladder shall have a multi-stage baked-on powder
coat finish.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
Maintenance Manual.
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance
DECK
VERTICAL LADDER
3/8" x 1-1/4"
3/8" x 1" O.D.
Washer
Button Head Bolt
Washer
3/8" x 1" O.D.
3/8" Lock Nut