pleasant hearth PH20D User manual

1
Warming Your Home. Warming Your Heart.
Heritage Compact Gas Fireplace Mantel
MODEL #PH20D
Questions, problems, missing parts? Before returning to your retailer,
call our customer service department at 1-877-447-4768,
8:30 a.m.-4:30 p.m., CST, Monday-Friday. Printed in China
80-10-102
6440 W. Howard St.
Niles, IL 60714-3302
877-447-4768

2
PART DESCRIPTION QTY. PART NO.
A Top Panel 1 80-06-001
B Base 1 80-06-002
C Left Side Panel 1 80-06-003
D Right Side Panel 1 80-06-004
E Front Panel 1 80-06-005
F Left Pilaster 1 80-06-006
G Right Pilaster 1 80-06-007
H Front Panel 1 80-06-008
J Corner Panel 1 80-06-009
K Corner Support 1 80-06-010
AA Bolt 30 80-09-001
BB Washer 30 80-09-002
CC Dowel 17 80-09-003
PACKAGE CONTENTS
HARDWARE CONTENTS
H
Bolt
Qty. 30
Dowel
Qty. 17
Washer
Qty. 30
E
D
G
F
K
C
B
A
J
AA BB CC

3
Carefully remove all pieces from carton and
make sure that you have all parts listed (refer
to parts list on page 2).
If you are missing parts, please call GHP
customer service at 1-877-447-4768.
1. Attach corner support (K) to base (B) with
bolt (AA) and washer (BB) through predrilled
holes as illustrated.
2. Attach left pilaster (F) to left side panel (C)
by securing from the back with washers (BB)
and bolts (AA) inserted through pre-drilled
holes as illustrated. Tighten with screwdriver.
Repeat using right pilaster (G) and right side
panel (D).
3. Insert 4 dowels (CC) into pre-drilled holes in
front panel (H). Slip left side panel assembly
over dowels (CC) on the left side of front panel
(H). Slip right side panel assembly over dowels
(CC) on the right side of front panel (H). Make
sure both panels are snug, then secure with
washers (BB) and bolts (AA) inserted through
pre-drilled holes as illustrated. Tighten with
screwdriver.
ASSEMBLY INSTRUCTIONS
1
2
3
B
K
BB
AA
G
D
BB
AA
F
C
BB
AA
E
CC

4
4. Set base (B) upright and insert 4 dowels
(CC) into pre-drilled holes in base (B). Slip
assembly over dowels in base (B). Make sure
assembly is snug, then secure with washers
(BB) and bolts (AA) inserted through pre-drilled
holes as illustrated. Tighten with screwdriver.
5. Insert 4 dowels (CC) into pre-drilled holes in
top edge of left and right pilasters (F&G). Slip
front panel (H) over dowels until snug, then
secure with washers (BB) and bolts (AA)
inserted through pre-drilled holes as illustrated.
Tighten with screwdriver.
6. Set top panel (A) on top of assembly. Secure
from the inside with bolts (AA) and washers
(BB) through predrilled holes as illustrated.
Tighten with screwdriver.
ASSEMBLY INSTRUCTIONS
4
5
6
B
BB
AA
H
BB
AA
BB
AA
A
CC
CC

5
7. Insert 3 dowels (CC) into pre-drilled holes
along back edge of top panel (A). Slip corner
panel (J) over dowels (CC) until snug. Secure
with bolts (AA) and washers (BB) through
predrilled holes as illustrated.
8. Align predrilled hole in glue block on
underside of corner panel (J) with predrilled
hole in corner support (K) and secure with
washer (BB) and bolt (AA) inserted through
pre-drilled holes as illustrated. Tighten with
screwdriver.
9. Set completed mantel in desired position in
room corner.
ASSEMBLY INSTRUCTIONS
7
8
9
J
CC
BB
AA
BB
AA