Plejd DIM-01-2P User manual
0353.2.5
DIM-01-2P
INSTALLATION MANUAL
Mains electricity
230 V/50 Hz
Standby power
0.3 W
External operating temperature
-20 to +35 °C
Dimensions
46x46x18 mm
Load type
1-pole or 2-pole with relay
Trailing edge
Leading edge
Protection
Overtemperature software
Overtemperature hardware
Overload software
Overload hardware
Radio
2.4 GHz mesh
Bluetooth®
Radio range
About 10 m indoors.
The Plejd mesh technology extends the range by
allowing the units to communicate with each other.
RISK OF INJURY TO PERSON OR PROPERTY
All work on the appliance must be
carried out by an authorized electrician.
National laws and regulations
must be followed.
Further information can be found
in the Plejd app or at plejd.com
Plejd AB
Krokslätts fabriker 27A
431 37 Mölndal
Sweden
Manufacturer | Plejd AB
Country of manufacture | Sweden
EN
Compliant to standards
Hereby, Plejd AB declares that the radio
equipment type DIM-01-2P is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity
is available at the following internet address:
plejd.com
12
L N NL
L
N
DIM-01-2P - 1 pol
12
L N NL
DIM-01-2P - 2 pol
L
N
1-pole switching of live (L) 2-pole switching of live (L)
and neutral (N)
Install the product in the appliance box behind the
push button/box lid or secure it with a Mounting clip
(MNT-01, not included) on the wall or DIN rail.
When installing in insulated or warm environments or
with several switches in the same box, the total power
is reduced.
DIM-01-2P is a universal dimmer with the option of
1- or 2-pole breaking. The product can withstand loads
of up to 300 W and has adjustable minimum, maximum,
and starting levels.
Connect the product
Do not use with: fluorescent lamps, conventional transformers,
or low-energy lamps.
Load
Halogen/incandescent (230 V) 0–300 W
LED light source/driver (230 V trailing edge) 0–200 VA
LED light source/driver (230 V leading edge) 0–100 VA
Electronic transformers (12 V halogen) 0–300 VA
Control inputs 1 and 2 can be used for control using:
- Push button (preset)
- Light switch
- Motion sensor (with neutral conductor)
The inputs can also be used to wirelessly control one
or more products from Plejd. A double click can be used
to activate lighting scenes.
The settings are easy to adjust in the app.
Support
Download the app and follow the instructions
Hand over the Plejd system
Hand over the Plejd system to your customer by writing
the system code on the included sticker . You’ll find the
code in the app once you have completed the installation.
Place the sticker in the distribution box and give the
welcome folder to the customer.
In the event of any technical questions, please contact
Plejd customer service.
HI!
NOTE!
During installation the product is non-dimmable.
Use the app to configure before use.
1
2
3
Download the Plejd app via the App Store or Google Play.
After supplying power to the unit by following the relevant
wiring diagram, use the app to complete the installation.
This requires Internet connection and Bluetooth®on your
phone/tablet. You do not need any additional equipment
to get started.
It’s simple to configure all relevant settings in the Plejd app.
The app can be used to schedule the lighting using the
astro/time schedule, control lighting, and wirelessly sync
control switches and scenes.
Control inputs 1 2
Other Plejd Relay manuals
