Plejd REL-02 User manual
REL-02
INSTALLATION MANUAL
0308.1.10
Mains electricity
230 V/50 Hz
Standby power
0.3 W
External operating temperature
-25 to +35 °C
Dimensions
46x46x18 mm
Type of switching
Relay, Micro gap (μ)
Protection
Overtemperature software
Zero crossing switching (breaker protection)
Radio
2.4 GHz mesh
Bluetooth®
Radio range
Up to 10 m indoors.
The Plejd mesh technology extends the range by
allowing the units to communicate with each other.
Further information can be found
in the Plejd app or at plejd.com
Plejd AB
Krokslätts fabriker 27A
431 37 Mölndal
Sweden
Manufacturer | Plejd AB
Country of manufacture | Sweden
RISK OF INJURY TO PERSON OR PROPERTY
All work on the appliance must be
carried out by an authorized electrician.
National laws and regulations
must be followed.
EN
Compliant to standards
Hereby, Plejd AB declares that the radio
equipment type REL-02 is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity
is available at the following internet address:
plejd.com
REL-02
12
L
N
N
NL L
1L2
Install the product in the appliance box behind the
push button/box lid or secure it with a Mounting clip
(MNT-01, not included) on the wall or DIN rail.
REL-02 has two relays with a 16 A breaking capacity for
resistive loads and a total breaking capacity of up to 16 A
(e.g., 10 A + 6 A).
Different loads have different inrush current when
switching on and voltage spikes when switching off. The
following table is recommended for different types of
lighting loads in order to ensure maximum service life.**
Maximum current 16 A.
Based on normal cable lengths and commonly available light fixtures
on the market.
**
Distributed on both outputs.*
Connect the product
1
Control inputs 1 and 2 can be used for control using:
- Push button (preset so that inputs 1 and 2 control
respective outputs 1 and 2)
- Light switch
- Motion sensor (with neutral conductor)
The inputs can also be used to wirelessly control one
or more products from Plejd. A double click can be used
to activate lighting scenes.
The settings are easy to adjust in the app.
Load PF Rated output* VA* A*
Halogen/incandescent (230V) 13,500 W 3,500 16
LED loads 0.9 800 W 1,000 4
Fluorescent lamp uncompensated 0.3 700 W 2,300 10
Fluorescent lamp compensated 0.85 1,500 W 1,750 8
Low voltage halogen electronic 0.8 1,500 W 1,750 8
Low voltage halogen convenonal 0.95 1,200 W 1,200 5
Low-energy lamps 0.6 500 W 800 4 Support
Download the app and follow the instructions
Hand over the Plejd system
Hand over the Plejd system to your customer by writing
the system code on the included sticker . You’ll find the
code in the app once you have completed the installation.
Place the sticker in the distribution box and give the
welcome folder to the customer.
In the event of any technical questions, please contact
Plejd customer service.
E-mail: [email protected] | Phone: +46 (0) 10 203 89 91
HI!
1 2
3
Download the Plejd app via the App Store or Google Play.
After supplying power to the unit by following the relevant
wiring diagram, use the app to complete the installation.
This requires Internet connection and Bluetooth®on your
phone/tablet. You do not need any additional equipment
to get started.
It’s simple to configure all relevant settings in the Plejd app.
The app can be used to schedule the lighting using the
astro/time schedule, control lighting, and wirelessly sync
control switches and scenes.
Control inputs 1 2
Other Plejd Relay manuals
