Plejd REL-01-2P User manual

REL-01-2P
0311.3.3
Mains electricity
230 V/50 Hz
Standby power
0.3 W
External operating temperature
-25 to +35 °C
Dimensions
46x46x18 mm
Type of switching
Relay, Micro gap (μ)
Protection
Overtemperature software
Zero crossing switching (breaker protection)
Radio
2.4 GHz mesh
Bluetooth®
<10 dBm
Radio range
Approx. 10 m indoors
The Plejd mesh technology extends the range by
allowing the units to communicate with each other.
RISK OF INJURY TO PERSON OR PROPERTY
All work on the appliance must be carried out by
an authorized electrician. National laws and
regulations must be followed.
Compliant to standards
Hereby, Plejd AB declares that the radio
equipment type REL-01-2P is in compliance
with Directive 2014/53/EU.
The full text of the EU declaration of
conformity is available at the following
internet address: plejd.com/compliance
EN
INSTALLATION MANUAL
Further information can be found
in the Plejd app or at plejd.com
Plejd AB, Krokslätts Fabriker 27A
431 37 Mölndal, Sweden
Disposal and recycling
This electrical product should not be disposed
of together with other household waste. Contact
your local recycling center for guidance on
electrical and electronic equipment disposal.
Important information
Do not use the product if it has visible signs
of damage.

Install the product in the appliance box behind the
push button/box lid or secure it with a Mounting clip
(MNT-01, not included) on the wall or DIN rail.
REL-01-2P has a relay with a breaker capacity of 16 A
in resistive loads. Due to heat build-up, the maximum
current is 13 A when switching both live (L) and neutral (N).
Different loads have different inrush current when
switching on and voltage spikes when switching off.
The following table is recommended for different types of
lighting loads as a guide to ensure maximum service life.
Connect the product
12
L
N
NNL LL
12
L
N
NNL
LL
REL-01-2P
1-pol brytning av L och N 2-pol brytning av L och N
12
L
N
NNL
LL
12
L
N
NNL LL
REL-01-2P
1-pol brytning av L och N 2-pol brytning av L och N
1-pole switching of live (L) 2-pole switching of phase (L)
and zero (N)
3,000 W/13 A when breaking 2-pole.*
Load PF Rated output VA A
Halogen/incandescent (230 V) 13,500 W 3,500 16*
LED loads 0.9 800 W 1,000 4
Fluorescent lamp uncompensated 0.3 700 W 2,300 10
Fluorescent lamp compensated 0.85 1,500 W 1,750 8
Low-voltage halogen electronic 0.8 1,500 W 1,750 8
Low-voltage halogen conventional 0.95 1,200 W 1,200 5
Low-energy lamps 0.6 500 W 800 4
Control inputs 1 and 2 can be used for control with:
· push button (preset)
· light switch
· motion sensor (with neutral conductor).
The inputs can also be used to wirelessly control one
or more products from Plejd. Additionally, double click
on a push button can be used to activate scenes.
Control inputs 1 2
Support
Follow the instructions in the app
Hand over the Plejd system
Once you have completed the installation, you will
find the system code in the app. Write the code on
the included sticker . Place the sticker in the
distribution box and give the welcome folder HI!
to the customer.
In the event of any technical questions,
please contact our customer service:
[email protected] | [phone]
Download the Plejd app on the App Store or Google
Play. After supplying power to the unit by following
the wiring diagram, use the app to complete the
installation. Setup requires Bluetooth®and an
internet connection.