Plus M-18 Series User manual

M-18/N-20 Series Copyboard
Stand Assembly Manual
WARNING
• Only specially trained technicians should perform installation operations.
• Please be sure to perform the installation and assembly based on this manual. Incorrect installation or assembly will be the cause of injury.
• Please have 2 or more persons lift the main unit when installing or removing it.
• For details on installation, also refer to the main unit’s “User’s Manual” and “Assembly and Setup Manual”.
• Remove the 4 stabilizers and unlock the caster stoppers before moving the stand.To prevent the toppling, be sure to remove the stabilizers
and unlock the stoppers.The toppling of the unit may result in bodily injury or damage to the machine.
This is the stand assembly manual for the M-18 and N-20 Series Copyboard.
The copyboard is referred to as "the set" or "the main unit" below.
* The Velcro is meant to prevent slipping, not to fasten the printer in place.
* Velcro is a registered trademark of Velcro Industries.
CAUTION
• When mounting the printer on the main unit, attach the *Velcro to prevent the printer from slipping out due to vibrations.
Remove the printer when moving the main unit. If not, the printer may fall, resulting in damage or injury.
• Diagrams of printers that appear in this manual are representative illustrations.
The illustration may differ from the actual printer. Check the owner's manual of your printer for information about the names of the connectors and
their locations and use.
Note
STAND PACKAGING LIST
Please open the carton and check the parts.
In the rare event that something is missing, please contact your store of purchase.
Name Assembly parts
T-shape legs (with casters) : 2 Screw caps: 2
Locking knobs 2
Cable cover: Mounted on stand
Horizontal bars:1 Mount screws (M5 x 20 mm):2
(temporarily fastened on side bar)
Mount screws (M5 x 45 mm): 2
Sleeves: 2
Plain washer :2
Name Assembly parts
Stabilizers:4 Hexagonal socket screws
(M5 x 8mm):8
Printer table/AC power adapter box: 1 set
(mounted on side bar)
Velcro: 2 sets
Hexagonal wrench
(width across flats: 3 mm): 1
ASSEMBLY OF THE STAND
2. Mount the T-shaped feet to the side bar.
The shorter side of the T-shaped foot is the back of the stand. The diagrams show the procedure from the back side.
Set the T-shaped foot with the cable cover on the right side (the printer table side).

Remove the temporary fixing tape from the ends of the side bar.
1
M5 screw
(mounted on
side bar)
Side bar
Temporary fixing tape Temporary fixing
tape
Space of about 2 mm
CAUTION
• Lock the casters of the T-shaped feet (left and right). If not, the stand could
slip, causing the stand or main unit to fall and resulting in injury or damage.
1. Lock the caster stoppers.
Press the bottom portion of the stoppers down to lock them.
Caster
Preparation: Mount the pen tray on the main unit.
For the mounting instruction, please refer to the “Assembly and Setup Manual”.

Printer table
Back (short)
Front (long)
Side bar
Screw cap
Screw hole
A. Hook
B. Stopper
M5 screw head
2 3 4
Side bar Hexagonal
wrench
Hexagonal
wrench
Sleeve
Plain washer
M5 x 45 mm screw
* The diagram used for
explanation here is
see-through.
Cable cover
3. Attach the stabilizers to the front and back of the T-shaped feet.

Insert the side bar's screw head into the T-shaped foot's screw hole (on the top), slide downwards, then use the
hexagonal wrench to partially fasten.

Insert the M5 x 45 screw and Plain washer into the sleeve, then use the hexagonal wrench to partially fasten it to the
side bar.
• Check that the sleeve is not sticking out.
• Once mounting of the left and right T-shaped feet is completed, tighten the four screws, adjusting so there is no looseness.

Fasten the screw caps to the screw heads of the left and right T-shaped feet.
A: With the screw caps set slightly at an angle, place the hooks into the screw holes in the T-shaped feet and slide downwards.
B: Press the stoppers of the screw caps into the hollows in the M5 screw heads.
CAUTION • To prevent toppling, be sure to install the stabilizers at each of the 4 locations. The toppling of this
machine could cause bodily injury or damage the machine.
Alignment of the screw holes of the T-shape feet with those of the
stabilizers.
Slide the stabilizers on the T-shaped feet to align with the holes.
CAUTION • Do not lift the stand to work on it. This may lead
to toppling or bodily injury.
Secure the stabilizers on the T-shape feet by hexagonal screws
using hexagonal wrench.
Attach the 4 stabilizers on the feet.
T-shape foot
Stabilizer
Hexagonal wrench
Hexagonal socket screws
(M5 x 8mm)

CAUTION
• To prevent accidental injury due to the main unit dropping or tipping over, the main unit should be held by at least two
persons when mounting it on the stand.
• Check that the stand's hooks are securely inserted into the main unit's mounting holes. If not, the main unit could drop,
resulting in injury and damaging the equipment.
• Make sure the locking knobs are tightened when moving. If not, the side bar's mounts could be bent or otherwise
damaged.
4. Mount the main unit on the stand.
Locking knobs
2
Back (short)
Front (long)
The rear frame
Mounting
hole
Hook
1
The shorter side of the T-shaped foot is the back of the stand. The diagrams show the procedure from the back side.
Place the stand's hooks in the mounting holes in the main unit's support pieces and insert securely in the hook
grooves.
Holes are located in three positions. The mounted height can be adjusted in three steps of 100 mm (1747, 1847 or 1947 mm
(maximum height)) according to which set of holes is used.
Fasten the main unit with the locking knobs (left and right).

Rear surface
Cable cover
Cable hole
Velcro
Velcro
Main unit's AC power adapter
Printer's AC power adapter
Cable clip
①
②
③Using the cable clip
Fasten the cables with the cable clip.
④
②
④
AC power adapter box
Rear surface
⑤
3. Store the AC power adapters and cables in the AC power adapter box.
Connect the main unit and printer before storing the adapters and cables.
The shorter side of the T-shaped foot is the back of the stand. The diagrams show the procedure from the back side.
Put the AC power adapters of the main unit and printer in the AC power adapter box.
Fasten the cables with the cable clip, then insert them in the cable cover.
Put the cables into the AC adapter box's cable hole. (The cables enter when pushed in.)
Peel the backing sheet of the Velcro and attach the Velcro to the bottom of the printer and the printer table. Fasten
the Velcro on the printer table in a position opposite the position on which the Velcro is attached on the printer.
Also, do not attach the Velcro to a sunken part of the printer, or it will not touch the Velcro on the printer table.
Place the printer on the printer table.
• Place any extra cable length in the AC power adapter box so that no cable is hanging out.
This completes mounting of the main unit on the stand. Make a test print.
CAUTION • Check that the AC power plug is not connected to a wall power outlet. If it is, be sure to unplug it.
WARNING
• The AC power adapters and the power cords generate heat. Be sure to wire them in such a way
that they keep apart. Do not bundle the cables together. Doing so could cause them to heat up,
leading to fire.
CAUTION
• The Velcro is attached to prevent slipping. It is not strong enough to prevent falling. Remove the
printer when moving the stand. If not, the printer could be damaged or fall on your feet, etc.,
causing injury.
26-4626-11B