Polly Products 3T32 Receptacle User manual

FS-3T32-CAP-02
Congratulations ! !
You have just purchased the finest recycled
plastic receptacle available. Enjoy ! ! !
Receptacle
3T32
For Fastener Pack
(FP-3T32-CU-02)

Before assembly, please make sure all components are included.
w/ 32 gal. Liner
D - ( 4 ) Four Connecting Blocks
FP - Fastener Pack
( 1 ) - One Fastener Pack
FP-3T32-CU-02
SBA-2T32-D
BP-2T32-F
w/ 32 gal. Liner (2 Open Sides)
SBA-2T32-E
E- ( 2 ) Two Connecting Spacers
BP-2T32-S3
Before assembly, please make sure all fasteners are included.
FS-3T32-CAP-02
Also needed for this assembly will be the following materials:
1 - #3 Phillips Drive Bit
#12 x 2 1/2" Pan Head Phillips Screw28 -
A - ( 1 ) One Left Receptacle B - ( 1 ) One Center Receptacle
FS-3T32-CAP-02
w/ 32 gal. Liner
SBA-3T32-D
C - ( 1 ) One Right Receptacle
LINER - T32
LINER - T32
LINER - T32

Before assembly, please make sure all fasteners are included.
Also needed for this assembly will be the following materials:
1 - #3 Phillips Drive Bit
#12 x 2 1/2" Pan Head Phillips Screw28 -
*IMPORTANT NOTICE*:
·DO NOT OVER-TIGHTEN SCREWS.
·USE A DRILL WITH ADJUSTABLE TORQUE FOR
BEST RESULTS.
·OVER-TIGHTENING WILL RESULT IN STRIPPING
OUT THE PILOT HOLE, AND SCREW WILL "SINK"
INTO THE PLASTIC WHICH MAY CAUSE A
STRESS FRACTURE.
FS-3T32-CAP-02

Step #1:
Take Receptacle "A", open the door
and remove the 32 gallon liner. Set
aside. Repeat for Recepacle "B" & "C".
Step #2:
With the door openings on
facing the same direction, Take
Receptacle "A" and place it as
close as possible to Receptacle
"B" (the sides without panels
facing each other, as shown).
FS-3T32-CAP-02

Step #3:
Align the pre-drilled holes in part "D" with the pilot holes at the base of
Receptacle "A" and "B" as shown above.
D
FS-3T32-CAP-02

Step #4:
Align the pre-drilled holes in part "D-1" to part "E" and the pilot holes in
the bottom of parts "A" & "B" as shown above. After the holes are
properly aligned, fasten with (1) One #12 x 2-1/2" Pan Head Phillips
Screw per hole.
Note: Do not tighten screws completely, this will be done at a
later step.
#12 x 2-1/2" Pan Head
Phillips Screw
D-1
E
FS-3T32-CAP-02

Step #5:
Take part "D-2" and line up the pre-drilled holes with the pilot holes
inside Receptacles "A" and "B" as shown above. With the holes aligned,
fasten (1) #12 x 2-1/2" Pan Head Phillips Screw per hole.
Note: Do not tighten screws completely, this will be done at a
later step.
#12 x 2-1/2" Pan Head
Phillips Screw
D-2
FS-3T32-CAP-02

Step #6:
Take Receptacle "C", with the door opening
facing in the same direction as Receptacles "A"
& "B", and repeat step #2 - #5 for Receptacles
"C" & "B" respectively.
FS-3T32-CAP-02
#12 x 2-1/2" Pan Head
Phillips Screw

FS-3T32-CAP-02
Note:
At this point the pre-drilled holes located at the top of Receptacle "B" and
the pilot holes in Receptacle "A" should be aligned, as well as the
pre-drilled holes in Receptacle "C" with the pilot holes in Receptacle "B".
(If they are not aligned, loosen screws that were previously fastened in
Steps #4 - #6.)
Step #7:
With the pre-drilled holes in Receptacle "B" and the pilot holes in
Receptacle "A" aligned, fasten (1) #12 x 2-1/2" Pan Head Phillips Screw
in each hole. Repeat for Receptacle "C" & "B", as shown above.
Note: Be sure to tighten screws completely after this step.
#12 x 2-1/2" Pan Head
Phillips Screw

Step #8:
Replace the 32 gallon liner in each receptacle.
FS-3T32-CAP-02