Polly Products FP-PC6BA-CU-02 User manual

FS-PC6BA-CAP-02
Congratulations ! !
You have just purchased the finest recycled plastic
park bench available. Enjoy ! ! !
Park Bench w/ Arms
6 Foot Park Classic
For Fastener Pack
(FP-PC6BA-CU-02)

Before assembly, please make sure all components are included.
B - Bench End
( 3 ) - Three Bench Boards
B - Bench End
( 3 ) - Three Bench Ends
20 - #12 x 3" Flat Head Phillips Screw
LB4BA
1
Before assembly, please make sure all fasteners are included.
FP - Fastener Pack
( 1 ) - One Fastener Pack
FS-PC6BA-CAP-02
FP-PC6BA-CU-02
PS-BTBE-P-02
BP-PC6B-A-02
( 2 ) - Two Bench Boards
BP-DB6B-A-03
( 2 ) - Two Bench Arms
BSA-PCBA-A-00
D - Bench Arm D - Bench Arm
A -2 x 4 Bullnose Bench Board
C - 2 x 4 Bench Board
A - 2 x 4 Bullnose Bench Board
E - 2 x 4 Bullnose Bench Board w/ Arm Holes ( 1 ) - One Bench Board
BP-PC6BA-A-02
F - 2 x 4 Bench Board w/ Arm Holes ( 1 ) - One Bench Board
BP-DB6BA-A-03
C - 2 x 4 Bench Board
A - 2 x 4 Bullnose Bench Board
B - Bench End

Before assembly, please make sure all fasteners are included.
#12 x 3" Flat Head Phillips Screw46 -
FS-PC6BA-CAP-02
Also needed for this assembly will be the following materials:
1 - #3 Phillips Drive Bit
*IMPORTANT NOTICE*:
·DO NOT OVER-TIGHTEN SCREWS.
·USE A DRILL WITH ADJUSTABLE TORQUE FOR
BEST RESULTS.
·OVER-TIGHTENING WILL RESULT IN STRIPPING
OUT THE PILOT HOLE, AND SCREW WILL "SINK"
INTO THE PLASTIC WHICH MAY CAUSE A
STRESS FRACTURE.

Fig #1:
In order to make the assembly of this Park Classic
Bench easier while going through the assembly
process the board positions are numbered and will be
referenced in later steps.
Step #1:
Stand (1) One bench end (Part B) upright and place (1) One bench board
(Part A) on position 1 being sure to place bullnose facing top of bench
align the pre-drilled holes to the pilot holes in the bench end. After the
holes are properly aligned, fasten with (1) One #12 x 3" Flat Head Phillips
Screw in the top pre-drilled hole.
Note: Do not tighten screw completely. This will be done in a later step.
FS-PC6BA-CAP-02
#12 x 3" Flat Head
Phillips Screw
1
2
3
4567

Step #2:
Stand the other bench end (Part B) upright and place the bench board
(Part A) already attached to the first bench end, on position 1 being sure to
align the pre-drilled holes to the pilot holes in the bench end. After the
holes are properly aligned, fasten with (1) One #12 x 3" Flat Head Phillips
Screw in the top pre-drilled hole.
Note: Do not tighten screws completely. This will be done in a later step.
FS-PC6BA-CAP-02
#12 x 3" Flat Head
Phillips Screw

Step #3:
Align bottom pre-drilled holes to the pilot holes in the bench end (Part B).
After the holes are properly aligned, fasten with (1) One #12 x 3" Flat
Head Phillips Screw per hole.
Note: Be sure to tighten screws completely after this step.
Step #4:
Place a bench board (Part A) on position 7 with bullnose facing front of
bench. Repeat Steps 1 - 3 to attach. Use (1) One #12 x 3" Flat Head
Phillips Screw per hole to fasten.
FS-PC6BA-CAP-02
#12 x 3" Flat Head
Phillips Screw

Step #5:
Repeat Steps 1 - 3 to attach bench board (Part A) on position 4 with
bullnose facing back of bench. Attach bench board (Part C) on positions
2 & 5. Attach bullnose bench board w/ arm hole (Part E) on position 3
with bullnose facing down and bench board w/ arm hole (Part F) on
position 6 with arm holes towards back of bench. Use (1) One #12 x 3"
Flat Head Phillips Screw per hole to fasten.
FS-PC6BA-CAP-02
#12 x 3" Flat Head
Phillips Screw

Step #6:
Position the bench arms (Part D) as shown above. Align the pilot holes
to the pre-drilled holes in the bench board w/ arm holes. After the holes
are properly aligned, fasten with (1) One #12 x 3" Flat Head Phillips
Screw per hole.
FS-PC6BA-CAP-02
#12 x 3" Flat Head
Phillips Screw

FS-PC6BA-CAP-02