Polly Products FP-EM8BA-CU-03 User manual

FS-EM8BA-CAP-03
Congratulations ! !
You have just purchased the finest recycled plastic
park bench available. Enjoy ! ! !
Park Bench w/ Arms
8 Foot Economizer
For Fastener Pack
(FP-EM8BA-CU-03)

Before assembly, please make sure all components are included.
B - Bench End
( 5 ) - Five Bench Boards
B - Bench End
( 4 ) - Four Bench Ends
32 - #12 x 3" Flat Head Phillips Screw
EM6BA
1
Before assembly, please make sure all fasteners are included.
FP - Fastener Pack
( 1 ) - One Fastener Pack
FS-EM8BA-CAP-03
FP-EM8BA-CU-03
PS-SBBE-D-03
BP-EM8B-A-03
( 1 ) - One Bench Board
BP-EM8BA-A-03
( 1 ) - One Bench Board
BP-EM8BA-B-00
( 2 ) - Two Bench Arms
BSA-EMBA-A-00
D - Bench Arm D - Bench Arm
A - 1 1/4 x 3 Bench Board
C - 1 1/4 x 3 Bench Board w/ Arm Holes
B - Bench EndB - Bench End
A - 1 1/4 x 3 Bench Board
A - 1 1/4 x 3 Bench Board
A - 1 1/4 x 3 Bench Board
A - 1 1/4 x 3 Bench Board
E - 1 1/4 x 3 Bench Board w/ Arm Holes

Before assembly, please make sure all fasteners are included.
#12 x 3" Flat Head Phillips Screw60 -
FS-EM8BA-CAP-03
Also needed for this assembly will be the following materials:
1 - #3 Phillips Drive Bit
*IMPORTANT NOTICE*:
·DO NOT OVER-TIGHTEN SCREWS.
·USE A DRILL WITH ADJUSTABLE TORQUE FOR
BEST RESULTS.
·OVER-TIGHTENING WILL RESULT IN STRIPPING
OUT THE PILOT HOLE, AND SCREW WILL "SINK"
INTO THE PLASTIC WHICH MAY CAUSE A
STRESS FRACTURE.

Fig #1:
In order to make the assembly of this Economizer
Bench easier while going through the assembly
process the board positions are numbered and will
be referenced in later steps.
Step #1:
Stand (1) One bench end (Part B) upright and place (1) One bench board
(Part A) on position 1 being sure to align the pre-drilled holes to the pilot
holes in the bench end. After the holes are properly aligned, fasten with
(1) One #12 x 3" Flat Head Phillips Screw in the top pre-drilled hole.
Note: Do not tighten screw completely. This will be done in a later step.
FS-EM8BA-CAP-03
#12 x 3" Flat Head
Phillips Screw
1
2
3
4567

Step #2:
Stand the other three (3) bench ends (Part B) upright and place the bench
board(Part A) already attached to the first bench end, on position 1 being
sure to align the pre-drilled holes to the pilot holes in the bench end. After
the holes are properly aligned, fasten with (1) One #12 x 3" Flat Head
Phillips Screw in the top pre-drilled hole.
Note: Do not tighten screws completely. This will be done in a later step.
FS-EM8BA-CAP-03
#12 x 3" Flat Head
Phillips Screw

Step #3:
Align bottom pre-drilled holes to the pilot holes in the bench end. After
the holes are properly aligned, fasten with (1) One #12 x 3" Flat Head
Phillips Screw per hole.
Note: Be sure to tighten screws completely after this step.
Step #4:
Place a bench board (Part A) on position 7. Repeat Steps 1 - 3 to attach.
Use (1) One #12 x 3" Flat Head Phillips Screw per hole to fasten.
FS-EM8BA-CAP-03
#12 x 3" Flat Head
Phillips Screw

Step #5:
Repeat Steps 1 - 3 to attach bench boards (Part A) on positions 2, 4 & 5.
Attach bench board w/ arm hole (Part C) on position 3 and bench board
w/ arm hole (Part E) on position 6. Use (1) One #12 x 3" Flat Head
Phillips Screw per hole to fasten.
*** When attaching bench board (Part C) in position 3 letter "C"
engraved on board will be at left side of the bench. When attaching
bench board (Part E) in position 6 letter "E" engraved on board will be on
the left side of the bench.
FS-EM8BA-CAP-03
#12 x 3" Flat Head
Phillips Screw

Step #6:
Position the bench arms (Part D) as shown above. Align the pilot holes
to the pre-drilled holes in the bench board w/ arm holes. After the holes
are properly aligned, fasten with (1) One #12 x 3" Flat Head Phillips
Screw per hole.
FS-EM8BA-CAP-03
#12 x 3" Flat Head
Phillips Screw

FS-EM8BA-CAP-03