PolyJohn MiniSan MSN01-1000 Instruction sheet

Page 1 of 9
June 2022
NOTE: We recommend reading through the entire Assembly Instructions prior to proceeding with use, service or maintenance.
MINISAN™
PRODUCT INSTRUCTIONS

MINISANTM
MSN01-1000
Page 2 of 9
June 2022
DIMENSION IMPERIAL METRIC
Base/Top/Dispensing Pipe 15”x15”x58” 38x38x147 cm
Maximum Hand Foam Dispensers 67.5 fl oz (2-1000 ml refill bags)
Number of Single Foam Dispenses 2,666 (2000-.75 ml dispenses)
Weight Empty 8 lb 3.63 kg
Base Capacity 2.2 gal 8.3 ltr
Advertising Area 8” x 10.5” 20.3 x 26.7 cm
PRODUCT SPECIFICATIONS
NOTE: All dimensions are subject to change due to environmental factors. All materials, including resin, pigments and additives used to make
the plastic components as well as the plumbing components that come in contact with the fresh water are U.S. FDA food grade compliant.

MINISANTM
MSN01-1000
Page 3 of 9
June 2022
The MSN01-1000 - MiniSan™ Hand Foam Dispenser is designed for use where hand washing is not available such as festivals, food service
locations, petting zoos, construction sites, etc., to be used indoors or out. The base can be lled with water or sand to provide additional
stability. It includes a large at area for advertising.
PRODUCT OVERVIEW
ASSEMBLY INSTRUCTIONS
GENERAL USE AND INFORMATION
Step 1. Fill the MSN01-0001 base with water or sand through the hole in the top of the post. If filling with sand, be sure to clean off all sand in
and around the top of the post.
Step 2. Insert the PC-000417 Uni-Seal in the hole in top of the Base
Step 3. Liberally apply some dish soap or other suitable lubricant to the inner surface of the Uni-Seal.
Step 4. Insert the stem at the bottom of the MSN01-0002 dispenser holder in the Uni-Seal, and firmly press the dispenser holder down onto the
base until seated.
Step 5. Mount the hand sanitizer dispenser (s) using the directions that came with the dispensers. PolyJohn carries two quality dispensers that fit
this product. We recommend the use of either the FD1-1000 Dispenser. The use of PC-000105 rivets is recommended to mount the dispensers.
Filling a Dispenser:
If this product is installed with the FD1-1000 foam dispenser from PolyJohn (recommended), then push up on the tab from underneath the
dispenser and pull down the cover. Fill with Rid-It™ - Foam Hand Sanitizer (follow the instructions located on the sticker inside of the foam
dispenser). Order Part #FD1-0004 for a case of 4 refills, available from PolyJohn. If this product is being used in a cold environment such as a
winter event, please order part # FD1-0004W. This is a case of 4 winter blend refills available from PolyJohn.
Draining the Base:
To drain the base if filled with water, pull up on the MSN01-0002 dispenser holder, while holding the base down. Remove the PC-000417 Uni-Seal ,
and tip the base over into a sink.

MINISANTM
MSN01-1000
Page 4 of 9
June 2022
PARTS DIAGRAM
EXPLODED VIEW
MSN01-0002
MiniSan
Dispenser Holder
PC-000417
3/4” Uni-Seal
MSN01-0001
MiniSan Base
FD1-1000
Foam Dispenser
(Sold Separately)

MINISANTM
MSN01-1000
Page 5 of 9
June 2022
Use a mild soap to clean all surfaces and component parts.
Minor scratches and abrasions can be lightly sanded or scrubbed with a mild abrasive cleaner (such as “Soft Scrub”) that contains calcium
carbonate, hypochlorate bleach, and detergents. Be sure to follow the cleaning product di- rections since these ingredients may cause hazardous
gases when mixed with other chemicals. Rinse the cleaned areas and buff with a conventional wax.
Some light scratches may also be hidden by using an industrial hot air gun.
For a source of cleaning, deodorizing and paper products contact:
PRO’S CHOICE
2500 GASPAR AVE.
WHITING, IN 46394-2175
800-292-1305
www.polyjohn.com/products/supplies/pros-choice.html
We highly recommend membership in the Portable Sanitation Association International (PSAI); the worldwide authority on portable sanitation
services. The PSAI, “Portable Sanitation Industry Certification Program” manual contains a wealth of information on standards and service
procedures. For more information contact the PSAI:
PORTABLE SANITATION ASSOCIATION INTERNATIONAL (PSAI)
7800 METRO PARKWAY, SUITE 104
BLOOMINGTON, MINNESOTA 55425 USA
800-822-3020 / 612-854-8300 FAX [phone]
www.psai.org
CLEANING AND MAINTENANCE
OPTIONAL ACCESSORIES,
SUPPLIES AND CHEMICALS
For a complete list of all our accessories, visit www.polyjohn.com/products/additional-products.html
For a complete list of all our chemicals, visit www.polyjohn.com/supplies/pros-choice.html
Foam Hand Sanitizer Rells
FD1-0004
Winter Foam Hand Sanitizer Rells
FD1-0004W
Foam Hand Sanitizer Dispenser
FD1-1000

MINISANTM
MSN01-1000
Page 6 of 9
June 2022
REGULATIONS
Prop 65
PolyJohn Corporation would like to inform any customers or end users that some products may contain chemicals listed in California’s Safe
Drinking Water & Toxic Enforcement Act of 1986. Commonly referred to as Proposition 65, this Act establishes a list of chemicals known by the
State of California to present a risk of cancer, birth defects, or other reproductive harm.
Chemical exposure typically occurs through inhalation, ingestion, or adsorption. PolyJohn products are not intended to be used in these methods.
PolyJohn Corporation cannot foresee all uses of their products (both intended and unintended uses) and as a result has opted to provide a
general warning of known chemical presence.
The Proposition 65 chemical list can be found at http://www.P65Warnings.ca.gov
The following warnings are labels placed on affected products. If these labels are not present then they do not apply to that product.
WARNING: This product can expose you to chemicals including 4-Vinylcyclohexene which is known to the State of California to cause
cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
4-Vinylcyclohexene label above to be used any product made with Bayblend T85
WARNING: This product can expose you to chemicals including titanium dioxide, which is known to the State of California to cause
cancer. For more information go to www.P65Warnings.ca.gov.
Conflict Minerals Compliance Statement
Section1502 of the Dodd-Frank Wall Street Reform and Consumer Protection Act, and the Securities and Exchange Commission Rules adopted in
connection therewith, require certain corporations to report the use of “Conflict Minerals” in the manufacture of their products. Generally, Conflict
Minerals collectively refers to cassiterite, columbite-tantalite, gold, wolframite, or their derivatives, including tantalum, tin and tungsten, which
originate from the Democratic Republic of the Congo or specified adjoining countries (referred to herein as “Covered Countries”).
While we, as a privately held corporation, are not subject to the Conflict Minerals rules and reporting requirements, we understand that our
customers may be, and we are committed to helping our customers comply with their reporting requirements. In order to determine if our
manufactured products contain Conflict Minerals, we have asked our relevant suppliers, as of September 1, 2020, to ascertain their use of any
Conflict Minerals in the materials they supply to us. Their responses demonstrate that our relevant suppliers (i) do not use Conflict Minerals in the
materials they supply to us, (ii) have no reason to believe the Conflict Minerals they use may have originated in the Covered Countries, and/
or (iii) reasonably believe that the Conflict Minerals they use are from recycled or scrap sources. Consequently, we can in turn represent that, to
the best of our knowledge, our manufactured products either do not contain Conflict Minerals, or to the extent they may, such products are “DRC
conflict free” as defined by paragraph (e)(4) of Section 1502.
We will continue to work with our key suppliers to ensure that we are able to identify the use of Conflict Minerals in our supply chain, and the
representations made in this compliance statement remain accurate. To that end, we reserve the right to amend this statement at any time based
on subsequent developments or information.
Should you have any questions or concerns regarding this statement, please do not hesitate to contact us.

MINISANTM
MSN01-1000
Page 7 of 9
June 2022
FREQUENTLY ASKED QUESTIONS
Hand Sanitizers
Q: How do I keep my SaniStand from tipping over?
A: Our SaniStand, ADA SaniStand, and MiniSan sanitizer dispensers have a base that can be filled with water or sand. There is a fill port that
you can put a garden hose to to fill with water or use a funnel to add sand to the base.
Q: What kind of dispensers can I put on the stands?
A: We have designed our stands to accept most dispensers on the market. We offer a wide variety of dispensers that work the best, but you do
have the option to add your own if desired.
Q: What is the large section on the top of the MiniSan dispenser for?
A: That area is for signage. You can add a sticker to your dispenser, so people recognize its use. You can also use it for advertising or directional
signs.

MINISANTM
MSN01-1000
Page 8 of 9
June 2022
WARRANTY
RESTROOMS AND TOILETS
POLYJOHN PORTABLE RESTROOMS LIMITED 3 YEAR PRODUCT WARRANTY
PolyJohn Enterprises Corp. warrants the major plastic parts of its portable restrooms (plastic front, wall panels, roof, and tank) against any
breakage or other problems that prevent the PolyJohn portable toilet from functioning in accordance with usual practices used in the portable toilet
industry and in their intended manner. This warranty covers any damages in material or workmanship for a total period of 3 years (36 months).
This warranty extends only to the original purchaser of the PolyJohn portable restroom. Proof of purchase, serial numbers, and photos will be
required.
SINKS, TANKS, TRAILERS AND SANISTANDS
PolyJohn Enterprises warrants our sinks, tanks, trailers and sanistands from the date of purchase. Any misuse or abuse of our products or failure to
properly follow recommended procedures shall void this warranty. The warranty is a 1 year limited warranty and a 90 day limited warranty for
components thereof.
What is Not Covered By Warranty
This warranty does not cover damage or failure contributed to or caused by: Not following PolyJohn assembly procedures, unauthorized
modification, acts of God, mishandling, misuse, use of incompatible solvents or other damaging chemicals, vandalism or accident. In no event
shall PolyJohn be liable for labor costs or for incidental or consequential damages.
For full details on PolyJohn’s warranty policy, and to view instructions for submitting a claim please visit https://www.polyjohn.com/warranty/.
Warranty Disclaimer
PolyJohn’s terms of sale are FOB (Free on Board Shipping Point). Meaning buyer takes on responsibility once it leaves PolyJohn’s shipping dock.
The carrier is wholly responsible for any damage incurred during transit. Important notice: All concealed/non-notated damages must be reported
within 5 business days of delivery (1st day is the day of delivery) as per the National Motor Freight Classification (NMFC) – Rule 300100 - for a
damaged claim to be filed. Reporting after this time will void a claim.
In order to prevent warranty disputes follow these steps immediately when receiving your products:
1. Inspect the shipment immediately and insist that visible damages be indicated on your copy of the freight bill. If they are not noted on the
freight bill it is very likely a claim will be denied.
2. Open the shipment if necessary, and inspect for any concealed damages.
3. If there are any damages that you cannot operate with you may refuse shipment. After you do this contact us immediately
Filing Process for Warranty
PolyJohn reserves the right to request inspection of products for verification of defect, which may include returning some or all of the parts with
shipping paid for by the purchaser. Once the items have been returned, inspected, and PolyJohn is found at fault shipping costs will be reimbursed.
You may contact PolyJohn to arrange for return shipping if desired.
To file your warranty claim follow these steps:
1. Go to polyjohn.com/warranty/
2. Fill out necessary contact information
3. Fill in invoice number, date of purchase, product, and product serial numbers.
4. Upload an images of affected products
5. Submit and someone will be in contact with you as soon as possible.

Page 9 of 9
June 2022
OUR MISSION STATEMENT
POLYJOHN USA
[phone]
Whiting, Indiana
www.polyjohn.com
POLYJOHN INTERNATIONAL
UNITED KINGDOM
[phone]
Yorkshire, England
www.polyjohn.co.uk
POLYJOHN INTERNATIONAL
CZECH REPUBLIC
[phone]
Karlovy Vary, Czech Republic
www.polyjohn.eu
POLYJOHN CANADA
[phone]
Oro Medonte, Ontario
www.polyjohn.ca
www.fr.polyjohn.ca
POLYJOHN LATIN AMERICA
+01 800-953-1307
Chihuahua, Mexico
www.polyjohn.mx
POLYJOHN NEW ZEALAND
[phone]
Auckland, New Zealand
www.polyjohn.co.nz
POLYJOHN SOUTH AMERICA
[phone]
Bogotá, Colombia
www.polyjohn.com
POLYJOHN AUSTRALIA
[phone]
Brisbane, Australia
www.totalsanitationsolutions.com.au
POLYJOHN SOUTHERN AFRICA
[phone]
Johannesburg, South Africa
www.polyjohn.co.za
“PolyJohn is a family owned, state of the art, plastics manufacturing company dedicated
to providing its employees with a work environment committed to excellence, and its
customers with innovative products, services and technology that meet or exceed their
requirements.”
THANK YOU FOR PURCHASING POLYJOHN PRODUCTS!