PolyJohn MiniSan MSN01-1000 User manual

MSN01-1000 MiniSan
August - 2014
Page 1 of 4
MSN01-1000 MiniSan
August - 2014
Page 2 of 4
MSN01-1000 MiniSan
Hand Foam Dispenser
Assembly Instructions
POLYJOHN
USA
PolyJohn Enterprises Corp
2500 Gaspar Ave.
Whiting, IN 46394
Phone: [phone]
Fax: [phone]
www.polyjohn.com
[email protected]
POLYJOHN
WORLDWIDE
PolyJohn (UK) Ltd.
Equinox 1 Audby Lane
Wetherby, England LS22 7RD
Phone: [phone]
Fax: [phone]
[email protected]
POLYJOHN
CANADA
PolyJohn Canada
P.O. Box 2300
199 Forest Plain Rd.
Orillia, Ontario LV3 6S2
Phone: [phone]
Fax: [phone]
[email protected]
Base/Top/Dispensing Pipe 15”x15”x58” 38x38x147 cm
Maximum Hand Foam
Dispensers
67.5  oz (2-1000 ml rell bags)
Number of Single Foam
Dispenses 2,666 (2000-.75 ml dispenses)
Weight Empty 8 lb 3.63 kg
Base Capacity 2.2 gal 8.3 ltr
Advertising Area 8” x 10.5” 20.3 x 26.7 cm
Specications
Dimension Imperial Metric
General Overview
The MSN01-1000 - MiniSan™ Hand Foam
Dispenser is designed for use where hand
washing is not available such as festivals,
food service locations, petting zoos, con-
struction sites, etc., to be used indoors or
out. The base can be lled with water or
sand to provide additional stability. It in-
cludes a large at area for advertising.
Shown with FD01-1000
Dispensers (Sold Separately)
Exploded View
MSN01-0002
MiniSan
Dispenser Holder
PC-000417
3/4” Uni-Seal
MSN01-0001
MiniSan Base
FD1-1000
Foam Dispenser
or FD1-2000
Hands Free
Foam Dispenser
(SoldSeparately)

MSN01-1000 MiniSan
August - 2014
Page 3 of 4
MSN01-1000 MiniSan
August - 2014
Page 4 of 4
General Use and Information
Assembly Instructions
Step 1. Fill the MSN01-0001 base with water or sand through the hole in the
top of the post. If lling with sand, be sure to clean o all sand in and around
the top of the post.
Step 2. Insert the PC-000417 Uni-Seal in the hole in top of the Base
Step 3. Liberally apply some dish soap or other suitable lubricant to the inner
surface of the Uni-Seal.
Step 4. Insert the stem at the bottom of the MSN01-0002 dispenser holder
in the Uni-Seal, and rmly press the dispenser holder down onto the base until
seated.
Step 5. Mount the hand sanitizer dispenser (s) using the directions that came
with the dispensers. PolyJohn carries two quality dispensers that t this prod-
uct. We recommend the use of either the FD1-1000 Dispenser, or the FD1-2000
Hands Free Dispenser. The use of PC-000105 rivets is recommended to mount
the dispensers.
Filling a Dispenser:
If this product is installed with the FD1-1000 or FD1-2000 foam dispensers
from PolyJohn (recommended), then push up on the tab from underneath the
dispenser and pull down the cover. Fill with Rid-It™ - Foam Hand Sanitizer
(follow the instructions located on the stickerinside of the foam dispenser). Order
Part #FD1-0004 for a case of 4 rells, available from PolyJohn. If this product
is being used in a cold environment such as a winter event, please order part #
FD1-0004W. This is a case of 4 winter blend rells available from PolyJohn.
Draining the Base:
To drain the base if lled with water, pull up on the MSN01-0002 dispenser
holder, while holding the base down. Remove the PC-000417 Uni-Seal, and tip
the base over into a sink.
CLEANING AND MAINTENANCE
Use a mild soap to clean all surfaces and component parts.
Minor scratches and abrasions can be lightly sanded or scrubbed with a mild abrasive
cleaner (such as “Soft Scrub”) that contains calcium carbonate, hypochlorate bleach and
detergents. Be sure to follow the cleaning product directions since these ingredients
may cause hazardous gases when mixed with other chemicals. Rinse the cleaned area
and bu with a conventional wax.
Some light scratches may also be hidden by using an industrial hot air gun.
For a source of cleaning, deodorizing and paper products contact:
COOPER’S OWN
2500 GASPAR AVE.
WHITING, IN 463942175
www.polyjohn.com/products/supplies/cooper-s-own
MISSION STATEMENT
“PolyJohn is a family owned, state of the art, plastics manufacturing company dedicated
to providing its employees with a work environment committed to excellence, and its
customers with innovative products, services and technology that meet or exceed their
requirements.”
THANK YOU FOR PURCHASING POLYJOHN PRODUCTS!
Look for us on the Web @ www.PolyJohn.com
We highly recommend membership in the Portable Sanitation Association International
(PSAI); the worldwide authority on portable sanitation services. The PSAI, “Portable
Sanitation Industry Certication Program” manual contains a wealth of information on
standards and service procedures. For more information contact the PSAI:
PORTABLE SANITATION ASSOCIATION INTERNATIONAL PSAI
7800 METRO PARKWAY, SUITE 104
BLOOMINGTON, MINNESOTA 55425 USA
8008223020 / 6128548300 FAX 6128547560
www.psai.org