Pop-A-Shot CLASSIC DUAL User manual

CLASSIC DUAL
SKU# PASCLAS19-02 WWW.POP-A-SHOT.NET

Required
Nylon head mallet (Not included) - for tapping corners
9/16” Wrench (Not included) - for installing rim
2x 7/16” wrench (not included) - for installing backboard to frame
Remove all the parts from the box and verify that you have all of the listed parts as shown on the parts list page.
Find a clean, level place to begin assembling your Pop-A-Shot game.
Like most things in life, putting together your Pop-A-Shot is better when done with a friend.
We hope you love your Pop-A-Shot and will let your friends and family (and any review sites)
know how you feel. If you do have a problem (and it happens), please let us know first and give us a chance to fix it.
Email: [email protected]
Read all instructions: All the safety and operating instructions should be read carefully before this
product is operated or played.
Caution: This is not a toy and is intended for use by or under the supervision of adults. Adults should
review safety guidelines with children to avoid possible risk of electric shock or other injuries.
Recommend:The game should be periodicallyexamined for conditions that may result in the risk of fire,
electrical shock or injury to persons. In the event such conditions exist, the game should not be used
until properly repaired.
Storage: This product is made from wood-based components and is sensitive toextreme temperatures
9/16” Deep Well Socket (Not included) - for installing rim
Recommended
Step ladder or stool
SKU# PASCLAS19-02
WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 2/15

ALL FRAME TUBE PARTS ARE LABELED
SKU# PASCLAS19-02
WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 3/15
POP-A-SHOT CLASSIC DUAL
FRAME ASSEMBLY
F4
F2
F1
B1
B4
S2
S1
B2 B3
F3
F5
T1
T2
T3
T4
F6
F7
F8
S3
S4
R7
R4
R5
R6

Rim and Net Ramp and Netting Set
Backboard
PARTS LIST
Control Panel
1x
Bolt for two rims
8x
Nut for two rims
8x
Long bolt for
backboard
4x
Washer for
backboard
8x
Nut for backboard
4x
AC Adapter
1x
Balls
7x
Pump
1x
1x
2x
SKU# PASCLAS19-02
WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 4/15
Inspect your box to make sure all parts are included

T1
T3
T4
T2
B1
B3
B4
B2
4-WAY JOINT
4-WAY JOINT
4-WAY JOINT
4-WAY JOINT
T-JOINT
T-JOINT
BOTTOM FRAME
STEP 1 TO BUILD BOTTOM FRAME
Connect F1 horizontally into Four-Way Joints on B1 and B3.
Connect R1 horizontally into Four-Way Joints on B2 and B4.
Connect B1 with B2, and B3 with B4 with Tee Joints.
Attach 4-Way Joints to each end of assembled bottom frames.
Front
Connect F2 vertically into Four-Way Joint on B1.
Connect F3 vertically into Four-Way Joint on B3.
Rear
Connect R2 vertically into Four-Way Joint on B2.
Connect R3 vertically into Four-Way Joint on B4.
TAP CORNERS AS YOU BUILD FRAME
SKU# PASCLAS19-02
WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 5/15
FRONT
REAR
F2
F3
F1
R2
R3
R1
COUPLER
B1
B3
B4
B2
TO BUILD TOP FRAME
Connect T1 with T2 and
connect T3 to T4.

STEP 2 TO BUILD FRONT FRAME
Connect F6 to F2 (Left Side), using Coupler.
Connect F7 to F3 (Right Side), using Coupler.
Slide F4 and F5 into holes in F2 and F3.
Connect 3-Way Elbows to top of F6 and F7.
Finish front frame with F8.
TAP CORNERS AS YOU BUILD FRAME
F4
F6
F7
F3
F2
F1
F8
F5
COUPLER
COUPLER
3-WAY ELBOW
3-WAY ELBOW
SKU# PASCLAS19-02
WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 6/15

STEP 3 TO BUILD THE BACKBOARD ASSEMBLY
Install: Two Bolts go to R4 to right side of Backboard,
then two other Bolts go to R5 and install Nuts on each
of the Bolts to hold Backboard.
Do not tighten the Four Nuts.
TAP CORNERS AS YOU BUILD FRAME
Connect the two Tee Joints to R7, then connect it to the
bottom of R4 and R5. Now tighten the Nuts to secure the Backboard.
SKU# PASCLAS19-02
WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 7/15
R5
R6
R7
TEE JOINT TEE JOINT
BACK BOARD

STEP 4 TO BUILD REAR FRAME
Connect R3 to R1. Connect R2 to R1. Connect R4 to R5 with
the Backboard Assembly.
TAP CORNERS AS YOU BUILD FRAME
SKU# PASCLAS19-02
WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 8/15
90° ELBOW
90° ELBOW
Backboard
Assembly
R5
R6
R7

STEP 5 ADD TOP FRAME AND SIDE SUPPORTS
Connect T1, T2, T3 and T4 to frame using 3-Way Elbows on the
front and Single Elbows on the rear. Connect S1, S2, S3 and S4
to the 45 ° elbows on the R4 and R5 of the back frame.
3-WAY ELBOW
SINGLE ELBOW
TOP FRAME BARS
T1
T2
Use a step ladder for
safety, where possible.
SKU# PASCLAS19-02
WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 9/13
T4
S4
S1
S3
S2
T3

STEP 6 Install Two Rims with hardware using the included Nuts and Bolts;
you will need a 9/16” Wrench, a 3/8” Drive Ratchet and a
9/16” Deep Well Socket (not included).
Note: Your sensor and scoreboard are pre-installed.
Please make sure the connections are secure.
SKU# PASCLAS19-02
WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 10/15

STEP 7 Take the Ball Return Ramp and attach the Velcro Sleeves
around the Top Side Tubes. Pull the Velcro under the
Lean Bar and wrap around the Horizontal Bar.
Pull the ramp under the Horizontal Tube under the Backboard and
attach the tabs to the Bolts of the Backboard.
Connect the Velcro Straps around the Rear Vertical Tubes, Middle.
VELCRO
VELCRO
VELCRO
VELCRO
YOU’RE READY TO PLAY!
SKU# PASCLAS19-02
WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 11/15

STEP 7
SKU# PASCLAS19-02
WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 12/15
Snap the Control Panel (#21) onto the Horizontal Bar.
Thread the Control Panel wire through the hole of the laminated
Game Operations “Cheat Sheet” until the Cheat Sheet is next
to the Control Panel.
Take the Control Panel wire and weave it through the side netting towards
the back of the Backboard. Plug the Control Panel wire into the outlet
labeled “Control Panel” in the Scoring Unit.
Tip: You’ll find complete game directions and operations in this booklet.
The “Cheat Sheet” is intended as a quick handy reference guide

PASCLAS19-02
WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 13/15
Now that you’ve put your Classic Dual together, let’s get started playing!

SKU# PASCLAS19-02
WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 14/15
© Copyright 2019 Pop-A-Shot
CLASSIC DUAL POP-A-SHOT GAME OPERATION
Game Options
Starting a game: Press START to start your game.
1. Standard Play
:30 on clock
Announcer and clock count down to start
Baskets are 2 points for 1st :20, then 3 points for final :10 and all bonus time
Bonus: :15 extra at 30 points; :10 extra at 60 points
2. Skeet Shooting
Announcers says “Shoot,” then you have :03 to make a basket
3. Double Or Nothing:
:30 on clock
First basket counts for 2 points, then each subsequent basket counts for double
If no basket is made within :03, next basket is 2 points
4. Overtime:
1:00 on clock
5. Sudden Death:
:15 on clock
6. Free Play:
All baskets count as 2 points

SKU# PASCLAS19-02
WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 15/15
© Copyright 2019 Pop-A-Shot
TROUBLESHOOTING
If your game isn’t powering on
• Check that the AC Adapter is plugged into the scoreboard. You can also use 4 AA
batteries to power the game.
If one side isn’t counting baskets
• Make sure you have chosen a multi-player game (such as Game 1) on your Control Panel.
• Make sure the sensors are securely plugged into the correct outlets in the
scoreboard (Step 13).
• Make sure the sensors are attached level, with the screws tightened all the way.
If the sensors are misaligned or angled at all, they will not correctly read the shots (Step 13).
• Check the connection between the sensors and the scoreboard (Step 13).
If neither side is counting baskets
• Make sure the sensors are securely plugged into the correct outlets in the
scoreboard (Step 13).
• Make sure the sensors are attached level, with the screws tightened all the way.
If the sensors are misaligned or angled at all, they will not correctly read the shots (Step 13).
• Check the connection between the sensors and the scoreboard (Step 13).
• Make sure the nets are correctly attached to the rims (incorrect placement can
block the sensors). The net’s longer loops should go through the hooks of the rim (Step 12).
Please visit www.pop-a-shot.net/support for more troubleshooting tips and hacks.