Pop-A-Shot PRO DUAL SHOT User manual

Rear Vertical Tube, Middle Rear Vertical Tube, Bottom
Front Vertical Tube, Bottom Horizontal Tube Upper Side Tube, Rear Upper Side Tube, Front Lower Side Tube, Rear
Lower Side Tube, Front
Rims
Control Panel
Pump Rim Bolt Rim Washer Rim Nut Scoring Bolt
Scoring Nut Screws
Balls Short Screw
Parts #17, #18 and #19
are in brown box
Long Screw Washer
Rim Nets
Scoring UnitSensors AC Adapter Ball Return Ramp
Lean Bar Braces Backboard Backplate
Front Vertical Tube, MiddleFront Vertical Tube, Top
PARTS LIST
Rear Vertical Tube, Top
x2 x2 x2
x2 x4 x2 x2 x2
x2
x2
x1
x1 x8 x16 x8 x4
x7 x18 x16 x34
x4 x1 x1 x1
x1 x4 x1 x2
x2x2
12345
6 7 8 9 10
11 12 13 14 15
16 17 18 19 20
21 22 23 24 25
26 27 28 29 30
x4
31
x8 x2

FRAME ASSEMBLY
POP-A-SHOT®PRO DUAL
12

Connect a Front Vertical Tube, Top (#4) to a
Front Vertical Tube, Middle (#5) and tighten with a
Short Screw (#23) and Washer (#25) (Fig 1A).
Connect the other end of the Front Vertical Tube, Middle (#5)
to the Front Vertical Tube, Bottom (#6) and tighten with a
Short Screw (#23) and Washer (#25)(Fig 1A).
Repeat with the other 4, 5 and 6 tubes.
Connect a Rear Vertical Tube, Top (#1) to a
Rear Vertical Tube, Middle (#2) and tighten with a Short Screw (#23)
and Washer (#25) (Fig 2A).
Connect the other end of the Rear Vertical Tube, Middle (#2)
to the Rear Vertical Tube, Bottom (#3) and tighten with a
Short Screw (#23) and Washer (#25).
Repeat with the other 1, 2 and 3 tubes.
STEP 1
STEP 2
Fig 1A
Fig 2A
6
5
4
1
2
3
23
23
25
25

Connect an Upper Side Tube, Rear (#8) to an
Upper Side Tube, Front (#9) and tighten with a
Short Screw (#23) and Washer (#25).
Repeat with the other 8 and 9 tubes.
Connect the Lower Side Tube, Rear (#10) to the
Lower Side Tube, Front (#11) and tighten with a
Short Screw (#23) and Washer (#25).
Repeat with the other 10 and 11 tubes.
STEP 3
STEP 4
8
23
25
9
10
11
25 23

Attach an Upper Side Tube, Rear (#8) to a
Rear Vertical Tube, Top (#1) using a
Long Screw (#24) and Washer (#25).
Repeat with the other 8 and 1 tubes.
Attach an Upper Side Tube, Front (#9) to a
Front Vertical Tube, Top (#4) using a
Long Screw (#24) and Washer (#25).
Repeat with the other 9 and 4 tubes.
STEP 5
STEP 6
Opposite side view
25
25
25
1
8
9
4
24
24
Opposite side view
25
24
24

6
11
25
24
Attach a Lower Side Tube, Front (#11) to a
Front Vertical Tube, Bottom (#6) using a
Long Screw (#24) and a Washer (#25).
Repeat with the other 11 and 6 tubes.
STEP 7
STEP 8
3
10 24
25
Attach a Lower Side Tube, Rear (#10) to a
Rear Vertical Tube, Bottom (#3) using a Long Screw (#24)
and Washer (#25).
Repeat with the other 10 and 3 tubes.

Attach a Horizontal Tube (#7) to both Front Vertical Tubes, Middle (#5)
using Long Screws (#24) and Washers (#25).
Attach another Horizontal Tube (#7) to both
Front Vertical Tubes, Bottom (#6) using
Long Screws (#24) and Washers (#25).
STEP 9
Attach a Horizontal Tube (#7) to both Rear Vertical Tubes,
Bottom (#3) using Long Screws (#24) and Washers (#25).
STEP 10
Attach another
Horizontal Tube (#7) to both
Rear Vertical Tubes, Top
(#1) using Long Screws (#24)
and Washers (#25).
24
25
24
25
7
5
5
24
25
24
25
7
6
6
24
25
7
2
1
1
2
3
3
7
24
25
24
25
24
25

Attach the Braces (#13) to the four bottom corners using
Short Screws (#23) and Washers (#25).
STEP 11
Loop the Rim Nets (#33) through the Net Hooks on the Rims (#16).
Make sure the longer strands are on top and go through the net hooks.
Attach the Rims (#16) to the Backboard (#14) using a Rim Bolt (#27)
and a Rim Washer (#28) on the front and a Back Plate (#15), Rim Washer
(#28) and Rim Nut (#29) on the back.
STEP 12
25
25
25
23
25
23
23
23
13
14
16
27
28
33
28
15 29

STEP 13 Attach the Scoring Unit (#18) to the Backboard (#14) with a Scoring Bolt
(#30) through the front of the Backboard and the Scoring Unit and secure
with a Scoring Nut (#31) in the back.
Put 4 AA Batteries into Scoring Unit (#18). Plug in AC Adapter (#19) to
Scoring Unit (#18).
30
14
18
31
32
19
18
17
Attach the Sensors (#17) using the Screws (#32). Make sure the Sensors are level
when attached. Plug the Bottom Sensor on the right side into the far right outlet of
the Scoreboard. Plug the Top Sensor on the right side into the next outlet of the
Scoreboard. Plug the Bottom Sensor on the left side into the next outlet. Plug the
Top Sensor on the left side into the next outlet.

STEP 14
24
24
24
25
25
25
24
25
Tip: If you can, grab a helper for this part.
Attach the Backboard (#14) to the Rear Vertical Tubes, Top (#1)
using Long Screws (#24) and Washers (#25).
14
1
1

STEP 16
STEP 15 Attach the Lean Bar (#12) to the Front Vertical Tubes,
Bottom (#6) using Short Screws (#23) and Washers (#25).
Take the Ball Return Ramp (#20) and attach the Velcro sleeves
around the Top Side Tubes (#8) & (#9). Pull the Velcro under the
Lean Bar (#12) and wrap around Horizontal Bar (#7). (Fig 16)
25 23
25 23
12
6
6
20
89
5
Pull the ramp under the Horizontal Tube
(#7) under the Backboard and attach the
tabs to the Bolts of the Backboard. Connect
the Velcro straps around the Rear Vertical
Tubes, Middle (#5))
14
7
12
Fig 16

Snap the Control Panel (#21) onto the Horizontal Bar (#7) (Fig 17a). Thread the
Control Panel wire through the hole of the laminated Game Operations
“Cheat Sheet” until the Cheat Sheet is next to the Control Panel.
Take the Control Panel wire and weave it through the side netting towards
the back of the backboard. Plug the Control Panel wire into the outlet
labeled “Control Panel” in the Scoring Unit.
Tip: You’ll find complete game directions and operations in this booklet.
The “Cheat Sheet” is intended as a quick handy reference guide
21
STEP 17
Fig 17a
12

TROUBLESHOOTING
If your game isn’t powering on
• Check that the AC Adapter is plugged into the scoreboard. You can also use 4 AA
batteries to power the game.
If one side isn’t counting baskets
• Make sure you have chosen a multi-player game (such as Game 1) on your Control Panel.
• Make sure the sensors are securely plugged into the correct outlets in the
scoreboard (Step 13).
• Make sure the sensors are attached level, with the screws tightened all the way.
If the sensors are misaligned or angled at all, they will not correctly read the shots (Step 13).
• Check the connection between the sensors and the scoreboard (Step 13).
If neither side is counting baskets
• Make sure the sensors are securely plugged into the correct outlets in the
scoreboard (Step 13).
• Make sure the sensors are attached level, with the screws tightened all the way.
If the sensors are misaligned or angled at all, they will not correctly read the shots (Step 13).
• Check the connection between the sensors and the scoreboard (Step 13).
• Make sure the nets are correctly attached to the rims (incorrect placement can
block the sensors). The net’s longer loops should go through the hooks of the rim (Step 12).
Please visit www.pop-a-shot.net/support for more troubleshooting tips and hacks.