Porta Phone TD900 Wireless User manual

Safety
Warranty
TD900 are warranted against defects in material and/or factory workmanship for a
period of two years from the date of purchase. Standard repairs due to misuse or
wear and tear, as well as replacement parts including but not limited to batteries,
padding, USB cable, etc. are excluded. Shipping is to Porta Phone at customer’s
expense, Porta Phone will pay for return ground shipping if the product warranty
applies to the repair.
Shipping
Prior to returning your headset for warranty or service you must call Porta Phone and
for an RA (Return Authorization) number: 1 [phone]
www.portaphone.com 1.800.233.1113
Double Channel Systems
General Service
All repair work will be performed for the cost of replacement parts and return shipping
from the Porta Phone factory.
Service
Porta Phone
145 Dean Knauss Dr
Narragansett RI 02882
TD900 Wireless
1. To prevent possible hearing damage, do not listen at high volume levels for long
periods.
2. Risk of explosion if battery is replaced by an incorrect type, dispose of battery
according to the instruction.
3. Recycle your products
The WEEE logo (shown at right) appears on the product to indicate that this product
must not be disposed of or dumped with your other household wastes. You are liable
to dispose of all your electronic or electrical waste equipment by transporting to an
appropriate collection point for recycling of such hazardous waste.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment.
IC Warning:
This device complies with Industry Canada license - exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2)
FCC Notice
This device complies with Part 15 of FCC rules. Operation is subject to the following 2 conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including
interference that may cause undesired operation. Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
MAXIMUM
POWER OUTPUT!
WEAR ON LEFT
OR RIGHT EAR
Mic boom swivels
270 degrees.
LITHIUM
BATTERIES
Provide continuous 6
hr operation and are
field replaceable.
SPREAD
SPECTRUM
Operating System

IMPORTANT
Double Channel TD 900
systems include TWO
headsets labeled “MAIN”.
These MAIN headsets must be turned “ON” to link the
corresponding REMOTE headsets.
Battery
TD 900 are powered by a Lithium Polymer battery that will operate 6 hours
when fully charged.
Operation
Set Volume
TD900 feature 5 volume settings. Select the desired volume by slowly
clicking the UP or DOWN buttons. Audible tone reflects volume level.
Double tone indicates low or max volume.
Head Coach Switch
Low profile switch is located on the bottom of
the Head-Coach headset earcup. Audible tone
confirms switching from offense to defense.
Headset Adjustments
Microphone mutes
when boom is in “UP”
position.
Boom swivels so
headset can be
worn on left or right.
Position microphone one-
finger width from your mouth.
Speak into the front-
indicated by TALK.
To preserve optimum charge level remove battery from
headsets when system not in use.
Battery Care
Each battery slot has a
corresponding LED indicator:
RED: Charging
GREEN: Fully Charged
Charging
1) Batteries are charged via the multi-charger.
2) Insert the batteries making sure the contacts
are properly aligned.
Installation
1) To Eject battery: press the release button
located at the top of the compartment.
2) To Insert battery: Snap battery into place.
Low Indicator
A repetitive beep (every 20 seconds) indicates
low power – battery should be charged or
replaced.
ON/OFF Power Button
1) Press the power button on the MAIN headset
– flashing LED indicates power is ON.
2) Press the power button on the REMOTE
headset(s).
3) The LED on all headsets will flash & then turn
solid indicating headsets have linked.
Note) To turn off, press and hold the power
button for 2 – 3 seconds. When LED turns red,
release.
ON / OFF Power
Volume UP / DOWN