Porter-Cable PIN138 User manual

1 - ENG PIN138
PIN NAILER
Cloueuse de goupilles
Clavadora
www.deltaportercable.com
INSTRUCTIVO DE OPERACIÓN, CENTROS
DE SERVICIO Y PÓLIZA DE GARANTÍA.
LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
Française : Page 15
Español: Página 30
Instruction manual
Manuel d'instructions
Manual de'instrucciones

2 - ENG
IMPORTANT SAFETY INSTRUCTIONS
FOR PNEUMATIC TOOLS
SAVE THESE INSTRUCTIONS
When using any pneumatic tool, all safety precautions, as outlined
below, should be followed to avoid the risk of death or serious injury. Read all instructions
before operating the tool.
DEFINITIONS - SAFETY GUIDELINES
The definitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.
Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Indicates a practice not related to personal injury which, if not avoid-
ed, may result in property damage.
• Actuating tool may result in flying debris, collation
material, or dust which could harm operator’s eyes.
Operator and others in work area MUST wear safety
glasses with side shields. These safety glasses must
conform to ANSI Z87.1 requirements (approved glasses
have “Z87” printed or stamped on them). It is the employer’s
responsibility to enforce the use of eye protection equipment
by the tool operator and other people in the work area.
(Fig.A)
• Always wear appropriate personal hearing and other
protection during use. Under some conditions and
duration of use, noise from this product may contribute
to hearing loss. (Fig. A)
• Use only clean, dry, regulated air. Condensation from an air
compressor can rust and damage the internal workings of the
tool. (Fig. B)
• Regulate air pressure. Use air pressure compatible with
ratings on the nameplate of the tool. [Not to exceed
100psi (6.9 bar).] Do not connect the tool to a compressor
rated at over 175 psi. The tool operating pressure must
never exceed 175 psi even in the event of regulator failure.
(Fig.C)
• Only use air hose that is rated for a maximum working
pressure of at least 150 psi (10.3 bar) or 150% of the
maximum system pressure, which ever is greater. (Fig.D)
70 psi
4.9 bar
Fig. C
Fig. B
Fig. A
Fig. D

3 - ENG
• Do not use bottled gases to power this tool. Bottled
compressed gases such as oxygen, carbon dioxide,
nitrogen, hydrogen, propane, acetylene or air are not
for use with pneumatic tools. Never use combustible
gases or any other reactive gas as a power source for
this tool. Danger of explosion and/or serious personal
injury may result. (Fig. E)
• Use couplings that relieve all pressure from the tool when
it is disconnected from the power supply. Use hose
connectors that shut off air supply from compressor
when the tool is disconnected. (Fig.F)
• Disconnect tool from air supply when not in use. Always
disconnect tool from air supply and remove fasteners
from magazine before leaving the area or passing the
tool to another operator. Do not carry tool to another
work area in which changing location involves the
use of scaffoldings, stairs, ladders, and the like, with
air supply connected. Do not make adjustments,
remove magazine, perform maintenance or clear
jammed fasteners while connected to the air supply.
(Fig. G)
• Connect tool to air supply before loading fasteners to
prevent a fastener from being fired during connection.
The tool driving mechanism may cycle when tool is
connected to the air supply. Do not load fasteners
with trigger or safety trigger depressed to prevent
unintentional firing of a fastener.
• Do not remove, tamper with, or otherwise cause the
tool or trigger to become inoperable. Do not tape or
tie trigger in the on position. Make daily inspections for
free movement of trigger. Uncontrolled discharge could
result.
• Inspect tool before use. Do not operate a tool if
any portion of the tool or trigger is inoperable,
disconnected, altered, or not working properly.
Leaking air, damaged parts or missing parts should
be repaired or replaced before use. Refer to Repairs.
(Fig.H)
• Do not alter or modify the tool in any way. (Fig. I)
• Always assume that the tool contains fasteners.
• Do not point the tool at co-workers or yourself at any
time. No horseplay! Work safe! Respect the tool as a
working implement. (Fig. J)
• Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control. When tool is not in use, it should be locked
in a safe place, out of the reach of children.
• Remove finger from trigger when not driving
fasteners.
• Never carry tool with finger on trigger. Accidental
discharge could result.
Fig. E
Fig. F
Fig. I
Fig. J
Fig. G
Fig. H

4 - ENG
• Do not overreach. Maintain proper footing and balance
at all times. Loss of balance may cause personal injury.
(Fig. K)
• Make sure hose is free of obstructions or snags.
Entangled or snarled hoses can cause loss of balance
or footing.
• Use the tool only for its intended use. Do not discharge
fasteners into open air, concrete, stone, extremely
hard woods, knots or any material too hard for the
fastener to penetrate. Do not use the body of the tool
or top cap as a hammer. Discharged fasteners may follow
unexpected path and cause injury. (Fig. L)
• Always keep fingers clear of nosepiece to prevent injury
from inadvertent release of nails. (Fig. M)
• Refer to the Maintenance and Repairs sections for
detailed information on the proper maintenance of the
tool.
• Always operate the tool in a clean, lighted area. Be
sure the work surface is clear of any debris and be
careful not to lose footing when working in elevated
environments such as rooftops.
• Do not drive fasteners near edge of material. The
workpiece may split causing the fastener to ricochet,
injuring you or a co-worker. Be aware that the nail
may follow the grain of the wood (shiner), causing it to
protrude unexpectedly from the side of the work material.
Drive the nail perpendicular to the grain to reduce risk of
injury. (Fig. N)
• Do not drive nails onto the heads of other fasteners
or with the tool at too steep an angle. Personal injury
from strong recoil, jammed fasteners, or ricocheted
nails may result. (Fig. O)
• Be aware of material thickness when using the nailer. A
protruding nail may cause injury.
• Be aware that when the tool is being utilized at
pressures on the high end of its operating range,
nails can be driven completely through thin or very
soft work material. Make sure the pressure in the
compressor is set so that nails are set into the material
and not pushed completely through. (Fig. P)
• Keep hands and body parts clear of immediate work
area. Hold workpiece with clamps when necessary to
keep hands and body out of potential harm. Be sure
the workpiece is properly secured before pressing the
nailer against the material. (Fig. Q)
• Do not use tool in the presence of flammable dust, gases
or fumes. The tool may produce a spark that could ignite
gases causing a fire. Driving a nail into another nail may
also cause a spark. (Fig. R)
• Keep face and body parts away from back of the tool
cap when working in restricted areas. Sudden recoil can
result in impact to the body, especially when nailing
into hard or dense material. (Fig. S)
Fig. K
Fig. L
Fig. M
Fig. N
Fig. O

5 - ENG
• Grip tool firmly to maintain control while allowing tool
to recoil away from work surface as fastener is driven.
• Do not actuate the tool unless the tool is placed firmly
against the workpiece. (Fig. T)
• DEPTH ADJUSTMENT: To reduce risk of serious injury
from accidental actuation when attempting to adjust
depth, ALWAYS:
• Disconnect air supply.
• Avoid contact with trigger during adjustments.
• Do not drive nails blindly into walls, floors or other
work areas. Fasteners driven into live electrical wires,
plumbing, or other types of obstructions can result in
injury. (Fig. U)
• Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool
while tired or under the influence of drugs or alcohol.
A moment of inattention while operating power tools may
result in serious personal injury.
Some dust created by power sanding, saw-
ing, grinding, drilling, and other construction activities con-
tains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
Use of this tool can generate and/or disburse
dust, which may cause serious and permanent respiratory or
other injury. Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles
away from face and body. Always operate tool in well-
ventilated area and provide for proper dust removal. Use
dust collection system wherever possible.
ALWAYS USE SAFETY GLASSES. Everyday
eyeglasses are NOT safety glasses. Also use face or dust
mask if operation is dusty. ALWAYS WEAR CERTIFIED
SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA respiratory protection.
Before operating this tool, carefully read all instructions
in Important Safety Instructions.
Fig. Q
Fig. R
Fig. S
Fig. P
Fig. T
Fig. U

6 - ENG
SAVE THESE INSTRUCTIONS
NAIL SPECIFICATIONS
PIN138
Nails 23 gauge wire (headless or slight head pins)
Lengths 5/8" (16 mm) –1-3/8" (35mm)
Air Inlet 1/4" NPT (6.4mm)
NOTE: Use only PORTER-CABLE approved fasteners
TOOL PARTS
A
H
C
B
F
Fig. 1
A. Trigger
B. Safety trigger
C. Air Inlet with quick
connect coupler
D. Rear exhaust
E. Magazine release
F. Magazine
G. Low nail indicator
window
H. Nosepiece
I. No-Mar pad
J. Belt hook
J
G
D
I
E
ASSEMBLY
Disconnect air line from tool and remove fasteners from magazine
before making adjustments or personal injury may result.
TRIGGER
Keep fingers AWAY from trigger when not driving fasteners to avoid
accidental firing. Never carry tool with finger on trigger.
The tool is shipped from the factory with a dual trigger actuation system.

7 - ENG
AIR FITTING
The tool is equipped with a 1/4" (6.4mm) male quick connector coupling. A 3/8" (9.5mm)
male quick connector coupling is available from PORTER-CABLE and may be used when
a 1/4" (6.4mm) supply line is not available.
NOTE: A 3/8" (9.5 mm) supply line (and fittings) are required for maximum tool
performance. IMPORTANT: Always use couplings that relieve all pressure from the tool
when it is disconnected from the power supply. Always use hose connectors that shut
off air supply from compressor when the tool is disconnected.
To install an air fitting
1. Wrap the male end of the fitting with thread seal tape prior to assembly to eliminate
air leaks.
2. To install a 1/4" (6.4mm) fitting: screw it directly into the air inlet and tighten firmly.
NOTE: If a cap is in the air inlet, remove it prior to inserting the fitting.
3. To install a 3/8" (9.5mm) fitting: screw the fitting into the 3/8" (9.5mm) adapter and
then into the air inlet of the tool and tighten firmly.
OPERATION
PREPARING THE TOOL
Read the section titled Important Safety Instructions for Pneumatic
Tools at the beginning of this manual. Always wear eye and ear protection when
operating this tool. Keep the nailer pointed away from yourself and others. For safe
operation, complete the following procedures and checks before each use of the nailer.
NOTE: These nailers are designed to be used without oil.
1. Before you use the nailer, be sure that the compressor tanks have been properly
drained. NOTE: Use a filter and regulator when possible.
2. Wear proper eye, hearing and respiratory protection.
3. Ensure magazine is empty of all fasteners.
4. Check for proper operation of trigger and safety trigger. Do not use tool if assembly
is not functioning properly.
5. Check air supply: Ensure air pressure does not exceed recommended operating
limits; 60 to 100 psi, (4.1 to 6.9 bar).
6. Keep tool pointed away from yourself and others.
7. Connect air hose.
8. Check for audible leaks around valves and gaskets. Never use a tool that leaks or
has damaged parts.
To reduce the risk of personal injury, disconnect tool from air supply
before performing maintenance, clearing a jammed fastener, leaving work area,
moving tool to another location or handing the tool to another person.
Using the Lock-off (Fig. 1)
To reduce the risk of injury. ALWAYS wear proper eye [ANSI Z87.1
(CAN/CSA Z94.3)] and hearing protection [ANSI S12.6 (S3.19)] when operating this tool.
Keep fingers AWAY from triggers when not driving fasteners to avoid
accidental firing. Never carry tool with finger on triggers.
Disconnect air line from tool and remove fasteners from magazine
before making adjustments or personal injury may result.

8 - ENG
The trigger is locked off until the safety trigger is depressed.
LOADING THE TOOL (FIG. 1–3)
Keep the tool pointed away from yourself and others. Serious personal
injury may result.
Never load nails with the trigger activated. Personal injury may result.
1. Read all Safety Warnings before using tool.
2. Connect the tool to air supply.
3. Push magazine release (E) and pull magazine (F) back. Make sure safety trigger has
the trigger locked off.
4. Insert fasteners into the side of the magazine (K). For fasteners with arrows the
direction arrow printed on the fasteners should point down into the bottom of
magazine. If no arrow is printed on the fasteners the nail points should point down
into the bottom of the magazine. NOTE: Make sure fasteners are placed firmly
against lower ledge of magazine.
5. Push magazine closed until it locks in place. Make sure the magazine snaps into
place.
6. Observe low nail indicator window (G) and reload when needed.
NOTE: The tool will not fire when only a few fasteners are left in the magazine, reload
fasteners to begin firing again.
Fig. 2
K
E
Fig. 3
G
F
ACTUATING TOOL (1, 4)
To reduce the risk of injury, ALWAYS Fig. 4
AB
wear proper eye [ANSI Z87.1 (CAN/CSA Z94.3)] and
hearing protection [ANSI S12.6 (S3.19)] when operating
this tool.
A nail will fire each time the trigger is
depressed which could result in accidental actuation.
1. Place the nosepiece against the work surface.
2. Depress the safety trigger (B) to unlock the trigger (A).
Now depress the trigger (A). A fastener is fired each
time the trigger is depressed.
Each time a fastener is fired, a blast of air will be exhausted from the rear
exhaust (D). Keep your face away from this area.

9 - ENG
ADJUSTING DEPTH
The depth that a fastener is driven is controlled by the pressure of the air supply. The
amount of air pressure required will vary depending on the length of the fastener and the
material being fastened. Experiment with the air pressure setting to determine the lowest
setting that will consistently perform the job at hand.
Air pressure in excess of that required can cause premature wear and/
or damage to the tool.
NO-MAR PAD AND WRENCH STORAGE (FIG. 5, 6)
Disconnect tool from air supply before removing or re-installing no-mar
pad.
The no-mar pad (I) is provided to reduce marring of the work surface. The no-mar pad
can be removed, and stored on the bracket (M), to provide increased depth-of-drive for
toe-nailing applications.
When not in use the hex wrench (L) supplied can be snapped into the storage bracket
as shown.
I
Fig. 5
M
Fig. 6 I
L
CLEARING A JAMMED NAIL (FIG. 1, 7)
Disconnect air line from tool and remove fasteners from magazine
before making adjustments or personal injury may result.
If a nail becomes jammed in the nosepiece, keep the tool pointed away from you and
follow these instructions to clear:
1. Make sure safety trigger (B) has the trigger Fig. 7
H
I
O
(A) locked off.
2. Disconnect air supply from tool.
3. Push magazine release (E) and pull maga-
zine (F) back. Remove fasteners.
4. Remove no-mar pad (I) and then using
3mm hex wrench to remove two bolts (O)
and nosepiece (H).
5. Remove the jammed fastener.
6. Examine the feed track and clear any dam-
aged pins or pin fragments.
7. Replace nosepiece and tighten bolts
securely.
8. Reattach air supply.
9. Reload the tool (see Loading the Tool).

10 - ENG
NOTE: Should nails continue to jam frequently in nosepiece, have tool serviced by an
authorized PORTER-CABLE service center.
COLD WEATHER OPERATION
When operating tools at temperatures below freezing:
1. Make sure compressor tanks have been properly drained prior to use.
2. Keep tool as warm as possible prior to use.
3. Make certain all fasteners have been removed from magazine.
4. Lower air pressure to 80 psi or less.
5. Reconnect air and load nails into magazine.
6. Turn pressure up to operating level (not to exceed 100 psi) and use tool as normal.
7. Always drain the compressor tanks at least once a day.
HOT WEATHER OPERATION
Tool should operate normally. However, keep tool out of direct sunlight as excessive
heat can deteriorate bumpers, O-rings and other rubber parts resulting in increased
maintenance.
BELT HOOK (FIG. 1, 8)
The integrated belt hook (J) can be assembled to either side of the tool to accommodate
left- or right- handed users. If the hook is not desired at all, it can be removed from the
tool.
To remove or assemble belt hook
1. Make sure safety trigger (B) has the trigger (A) locked off.
2. Disconnect the tool from air supply.
3. Using the appropriate hex wrench, remove the belt hook (J).
4. Assemble belt hook to other side of nailer in hole (P) and tighten screw securely.
Fig. 8
J
P

11 - ENG
MAINTENANCE
Disconnect air line from tool and remove fasteners from magazine
before making adjustments or personal injury may result.
DAILY MAINTENANCE CHART
ACTION WHY HOW
Drain compressor
tanks and hoses daily. Prevents accumulation of moisture in
compressor and nailer.
Open petcocks or other
drain valves on compressor
tanks. Allow any accumulated
water to drain from hoses.
Clean magazine and
magazine release. Permits smooth operation of magazine,
reduces wear and
prevents jams.
Blow clean with compressor
air. The use of oils, lubricants
periodically or solvents is
not recommended as they
tend to attract debris.
Before each use, check
to insure all screws,
nuts and fasteners are
tight and undamaged.
Prevents jams, leaks
and premature failure
of tool parts.
Tighten loose screws or other
fasteners using the appropriate
hex wrench or screwdriver.
CLEANING
Never use solvents or other harsh chemicals for cleaning the non-
metallic parts of the tool. These chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
REPAIRS
For assistance with your tool, visit our website at www.deltaportercable.com for a list of
service centers, or call the PORTER-CABLE Customer Care Center at (888)848-5175.
SERVICE
REPLACEMENT PARTS
Use only identical replacement parts. For a parts list or to order parts, visit our service
website at www.deltaportercableservicenet.com. You can also order parts from your
nearest PORTER-CABLE Factory Service Center or PORTER-CABLE Authorized
Warranty Service Center. Or, you can call our Customer Care Center at (888)848-5175.
SERVICE AND REPAIRS
All quality tools will eventually require servicing and/or replacement of parts. For information
about PORTER-CABLE, its factory service centers or authorized warranty service centers,
visit our website at www.deltaportercable.com or call our Customer Care Center at (888) 848-
5175. All repairs made by our service centers are fully guaranteed against defective material
and workmanship. We cannot guarantee repairs made or attempted by others.
You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson,
Tennessee 38305 - Attention: Product Service. Be sure to include all of the information shown
on the nameplate of your tool (model number, type, serial number, etc.).

12 - ENG
ACCESSORIES
Since accessories, other than those offered by PORTER-CABLE, have not
been tested with this product, use of such accessories with this tool could be hazardous. To
reduce the risk of injury, only PORTER-CABLE recommended accessories should be used
with this product.
A complete line of accessories is available from your PORTER-CABLE Factory Service Center
or a PORTER-CABLE Authorized Warranty Service Center. Please visit our Web Site www.
deltaportercable.com for a catalog or for the name of your nearest supplier.
THREE YEAR LIMITED WARRANTY
PORTER-CABLE will repair, without charge, any defects due to faulty materials or
workmanship for three years from the date of purchase. This warranty does not cover part
failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty
repair information, visit www.deltaportercable.com or call [phone]. This warranty does
not apply to accessories or damage caused where repairs have been made or attempted by
others. This warranty gives you specific legal rights and you may have other rights which vary
in certain states or provinces.
In addition to the warranty, PORTER-CABLE tools are covered by our:
1 YEAR FREE SERVICE: PORTER-CABLE will maintain the tool and replace worn parts
caused by normal use, for free, any time during the first year after purchase.
90 DAY MONEY BACK GUARANTEE: If you are not completely satisfied with the performance
of your PORTER-CABLE Power Tool, Laser, or Nailer for any reason, you can return it within 90
days from the date of purchase with a receipt for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, see country specific warranty information contained in the
packaging, call the local company or see website for warranty information.
To register your tool for warranty service visit our website at www.deltaportercable.com.
WARNING LABEL REPLACEMENT
If your warning labels become illegible or are missing, call [phone] for a free
replacement.

13 - ENG
TROUBLESHOOTING GUIDE
MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART
BELOW. FOR MORE SERIOUS OR PERSISTENT PROBLEMS, CONTACT A PORTER-
CABLE SERVICE CENTER OR CALL 1 888 848-5175.
To reduce the risk of serious personal injury, ALWAYS disconnect
air from tool before all repairs.
SYMPTOM PROBLEMS SOLUTIONS
Air leak near top of
tool or in trigger area Loose screws. Tighten screws.
Worn or damaged
o-rings or seals. Install Overhaul Kit (Part # 60117).
Tool does nothing or
operates sluggishly Inadequate air supply. Verify adequate air supply.
Worn or damaged
o-rings or seals. Install Overhaul Kit (Part # 60117).
Fastener jammed in nosepiece. See Clearing a Jammed Nail.
Air leak near
bottom of tool Loose screws. Tighten screws.
Worn or damaged
o-rings or bumper. Install Overhaul Kit (Part # 60117).
Tool jams frequently Incorrect fasteners. Verify approved fasteners
of correct size.
Fastener fragments
jammed in nosepiece. See Clearing a Jammed Nail.
Fasteners loaded incorrectly. Verify fasteners are loaded
correctly. See To Load Tool.
Damaged fasteners. Replace damaged fasteners.
See To Load Tool.
Magazine or nose screws loose Tighten screws.
Magazine is dirty. Clean magazine.
Driver tip is worn or
damaged. Install Driver Maintenance (Part # 60118).
Tool does not fire Only a few fasteners are
left in the magazine Reload fasteners to begin firing again.
Other Contact a PORTER-
CABLE Authorized
Warranty Service Center
TOOL SPECIFICATIONS
PIN138
Height (inch/meter) 7.5/.19
Width (inch/meter) 1.9/.05
Length (inch/meter) 8.1/.21
Weight (lbs/kg) 2.1/0.95
Recommended Operating Pressure 60-100 psi (4.1 to 6.9 bar)
Air Consumption per 100 cycles 1.61 SCF
Loading capacity 132 nails
Lubrication Oil-Free

14 - ENG
Portable
Handcarry
3.2 – 4 CFM
5.5 HP Gas
2 HP Elec.
8 – 9 CFM
8 HP Gas
14 – 16 CFM
Industrial
23+ CFM
NUMBER OF TOOLS CONNECTED TO COMPRESSOR
1
2
3
4
NR
5
NR
6
NR NR
7
NR NR
8+
NR NR
Compressor will be sufficient for tools at all production rates.
Compressor will be sufficient at slow or moderate production rates,
but may have difficulty at very rapid rates.
Compressor will be adequate only when tools are utilized at slow
production rates (punch-out or occasional use).
NR
Not Recommended