Porter NITRONOX HD User manual

FM-1310 Rev. B 04/2018 www.porterinstrument.com/nitronox
PORTER NITRONOX HD E-STAND PACKAGE
ASSEMBLY INSTRUCTIONS
Warnings and Precautions
Important: In addition to these
assembly instructions, read the
Nitronox HD User’s Manual /
Instructions FM-1308, which
includes:
Warnings and Precautions
Delivery Technique
Self-Administration Description
Safety Checks
Good Practices using Cylinders
Maintenance and Troubleshooting.
Examination
Examine shipping carton for signs of external damage.
Remove contents from carton and inspect for visible damage or missing parts.
If damage is discovered or suspected and/or parts are missing, notify Porter or authorized
distributor immediately.
PORTER CUSTOMER SERVICE: 215-723-4000

Installations
Nitronox Main Housing, Mobile E-Stand (Fig. 1.1), Mobile Stand, Wall Mount (Fig. 1.2) Mounted
Demand Valve, Scavenger Interface
Preparation of Mobile E-Stand Fig. 1.1
Also see FM-916 E-Stand User’s Instructions
1. Slide Center Column with Cylinder
Restraint and Cylinder Yoke Block into 5-
Star Base (Fig. 2.1). Push down firmly until
snug. Align Cylinder Restraint as shown.
Base of cylinders will fit in between wheels
(Fig. 2.2).
2. Adjust the Recessed Mounting Post to
highest height by loosening and tightening
the small black handle (Fig. 3.1) on the
Yoke Block – and raising the Mounting Post
(Fig. 3.2).
3. The Nitronox Main Housing will mount on
the Mounting Post of the E-Stand [or Mobile
Stand] by sitting the bottom of the Housing
(Fig. 4.1) on top of the Mounting Post
(larger threads Fig. 4.2). Hold the Mounting
Post in one hand and position the Housing
with the other.
4. Secure the Housing on the Mounting Post
(Fig. 5.1) by twisting the Post
(counterclockwise) with one hand and
holding the Housing steady with the other
hand. Twist until the Post is snug (Fig. 5.2).
E-Stand with Nitronox Wall Mount
2
Fig. 1.1
Fig. 2.1 Fig. 2.2
Fig. 3.1 Fig. 3.2
Fig. 5.1
Fig. 5.2
Fig. 4.2
Fig. 4.1
Fig. 1.2

Preparation of Mobile E-Stand (continued)
5. Attach the Handle (Fig. 6.1) to the Mounting
Post – just under the Retaining Ring / O-
ring (Fig. 6.2). Firmly tighten both screws so
that the Handle cannot be twisted. The
back of the Handle should be positioned
over the back two cylinders (Fig. 6.3).
6. Carefully clip the [shipping accessory]
plastic fasteners off of the green Oxygen
Hose and blue Nitrous Oxide Hose – under
the E-Stand Block (Fig. 7). Be careful – do
not cut the Hoses.
7. Connect the Diameter Indexed Safety
System (DISS) color-coded green [white]
Oxygen and blue Nitrous Oxide Hoses to
the appropriate connections (Fig. 8.1) on
the bottom of the Nitronox Main Housing.
Slide the Hoses through the opening in the
Handle (Fig. 8.2) before connecting. Firmly
tighten the Hoses using a wrench.
Fig. 8.3
3
Fig. 6.2
Fig. 6.1
Fig. 6.3
Fig. 8.1
Fig. 8.2
Fig. 7

Preparation of Nitronox HD Scavenger
Parts for use with Porter Medical
Breathing Circuit
For further details, refer to Nitronox HD
Scavenger System User’s Manual FM-1309
and Porter Medical Breathing Circuit FM-1304
8. Attach Demand Valve Manifold Mount
Assembly to the right side of the Nitronox
HD using one screw on the top (Fig 9.1)
and one screw on the bottom (Fig 9.2).
9. Push Demand Valve into Manifold (two
sealing o-rings). (Fig. 10)
10. Tighten thumb screw of Retaining Bracket
to the side of the Manifold to secure the
Demand Valve (Fig. 11)
11. Connect the Gas Delivery Hose to Demand
Valve (Fig. 12). This is a quick connect
attachment. Push the two ends together
until click sound is heard. To remove –
push the metal clip in – and pull apart.
12. Attach Mask Hanging Bracket to the Left
side of the Nitronox HD (Fig. 13).
Fig. 13
13. Assembled Nitronox HD unit (Fig. 14).
Fig. 14
14. Attach the Nitronox Scavenger Interface to
the Center Column (Figs. 15.1, 15.2).
Fig. 9.1 Fig. 9.2
Fig. 15.1 Fig. 15.2
Fig. 10
Fig. 11 Fig. 12
4

Attachment of Cylinders
15. Loosen the Tee Handle (Fig. 16.1) until
point is even with the inside of the Swivel
Arm. Push Tee Handle inwards to flip to
open position. Align Tee Handle vertically
(Fig. 16.2).
16. Undo the Hook & Loop straps on the
Cylinder Restraint (Fig. 17)
17. Cylinder Preparation: Remove any plastic
wrap from the top of cylinder, including the
cylinder plastic washer. Verify that the
rubber washer (Fig. 18.2) provided with the
E-Stand is still in place. Use the E-Stand
washer.
18. Mount the “E” cylinders of Oxygen and
Nitrous Oxide (not included) to the E-Stand
Block. Insert cylinders correctly on indexing
pins and as marked on Block (N
2
O Figs.
18.1, 18.2; O
2
Figs. 18.3, 18.4). Pins assure
mounting in appropriate position.
N
2
O Pins Rubber
Washer
O
2
Pins
Warning
Do not remove or alter
gas indexing pins
19. Slide the cylinder into place by lining up the
pins and pin holes on the cylinder. Push
into place. Properly placed, the cylinder
should hang on the pins (Fig. 19).
20. Cylinders should hang freely between
wheel base. If the wheel base interferes,
loosen and rotate cylinder restraint.
21. Rotate swivel clockwise to close (Fig. 20.1).
Swivel will move into the locked position
when Tee Handle is tightened. Secure the
Hook & Loop straps to hold cylinder in
place (Fig. 20.2).
22. The Cylinder Valve Wrench (hanging from
black Knob) is used to open/close Cylinder
Valves (Fig. 21). See FM-916 User’s
Instructions.
5
Caution: When operating the swivel yoke,
take care not to catch or pinch fingers.
Fig. 16.1
Fig. 19
Fig. 20.2 Fig. 21
Fig. 20.1
Fig. 18.3
Fig. 18.4
Fig. 16.2
Fig. 17
Fig. 18.2
Fig. 18.1

CERTIFICATE OF WARRANTY
THIS WARRANTY IS GIVEN IN PLACE OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE OR OTHERWISE.
Under no circumstances shall Parker Hannifin Corporation be liable for incidental or consequential
damages as those terms are defined in the uniform commercial code.
Parker Hannifin Corporation, Porter Instrument warrants that each product or part shall be free from
defects in workmanship and materials, under normal use and with appropriate maintenance, for one
(1) year from the date of delivery to customer unless otherwise specified in writing. All rubber and
plastic parts and accessories are warranted under the same conditions for a period of ninety (90) days
from date of purchase.
No statement or claim about the product by any employee, agent, representative, or dealer of Parker
Hannifin Corporation shall constitute a warranty by Parker Hannifin Corporation or give to rise to any
liability or obligation of Parker Hannifin Corporation.
Parker Hannifin Corporation shall not be liable for any damage, injury or loss arising out of the use of
the product, whether as a result of a defect in the product or otherwise, if, prior to such damage, injury
or loss, the product was (1) damaged or misused; (2) repaired, altered or modified by persons other
than Parker Hannifin Corporation; (3) not installed in strict compliance with applicable codes and
ordinances; or (4) not installed by an authorized Parker Hannifin Corporation dealer. Parker Hannifin
Corporation's obligation for breach of this warranty, or for negligence or otherwise, shall be strictly and
exclusively limited to the repair or replacement of the product or part. This warranty shall be void on
any product on which the serial number has been altered, defaced or removed.
Parker Hannifin Corporation
Precision Fluidics Division
Porter Instrument
245 Township Line Road
Hatfield, PA 19440
Office 215 723 4000
Fax [phone]
This product complies with the Medical Device Directive (93 / 42 / EEC).
A “Declaration of Conformity” in accordance with the directive has been made and is on file.
European Communities should contact the Authorized Representative listed below regarding
any Medical Device Directive (MDD) inquiries.
Contact Name: Parker Hannifin Ltd Instrumentation Products Division
Mailing Address: Riverside Road, Pottington Business Park
Barnstaple, EX 31 1NP, England
Phone: [phone] Fax: [phone]
The Quality System for Porter Instrument is certified to ISO 13485. The scope of our registration is:
“The design, manufacture, distribution and servicing of Nitrous Oxide – Oxygen Sedation Flowmeters,
Gas Scavenging Systems, Gas Distribution Systems and Office Communication Systems for use by a
physician, dentist or licensed healthcare Profession.”
Check our website: www.porterinstrument.com for additional information.
To register your product: www.porterinstrument.com/resources-dental choose Warranty tab.
To download a User’s Manual: www.porterinstrument.com/resources-dental choose Manuals tab