Portfolio WLL103BZ User manual

Français p. 12
Español p. 23
ATTACH YOUR RECEIPT HERE
Purchase Date
PH18716 1
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday,
8 a.m. - 5 p.m., EST, Friday.
PORTFOLIO®and PORTFOLIO & DesignTM
are trademarks or registered trademarks of
LF, LLC. All rights reserved.
APPROVED FOR USE
IN WET LOCATIONS
ITEM #1085711
1085712
MODEL #WLL103BZ
WLL104BZ
WALL LANTERN

2
Package Contents ...............................................................................................................3
Hardware Contents
..........................................................................................................................
Safety Information ...............................................................................................................
Preparation .........................................................................................................................
Assembly Instructions .........................................................................................................
Operating Instructions ........................................................................................................
Care and Maintenance ......................................................................................................
Troubleshooting..................................................................................................................
Warranty ............................................................................................................................
TABLE OF CONTENTS
3
4
6
10
5
10
10
11

3
PACKAGE CONTENTS
A
B
C
D
E
F
G
A Fixture 1
B Mounting Strap 1
(preassembled to fixture (A))
C Washer 2
(preassembled to screw (F))
D Decorative Nut 2
(preassembled to screw (F))
E Nut 2
(preassembled to screw (F))
F Screw 2
(preassembled to mounting strap (B))
G Sensor 1
(preassembled to fixture (A))
H Sensor Cap 1
(preassembled to sensor (G))
PART DESCRIPTION QUANTITY
HARDWARE CONTENTS (shown actual size)
Wire
Connector
Qty. 3
AA BB
Machine
Screw
Qty. 2
H

4
SAFETY INFORMATION
READ AND SAVE THESE INSTRUCTIONS.
DANGER
• For your protection and safety, carefully read and understand the information provided in this manual
completely before attempting to assemble, install or operate this product. Failure to do so could lead
to electrical shock, fire or other injuries that could be hazardous or even fatal.
• If using this light fixture in a WET location, this light fixture must be connected to a supply
circuit that is protected by a Ground Fault Circuit Interrupter (GFCI) to reduce the risk of personal
injury, electrical shock or death.
• DO NOT connect this fixture to an electrical system that does not provide a means for equipment
grounding. Never use a fixture in a two-wire system that is not grounded. Installing a fixture into an
electrical system not having a proper grounding means could cause metal parts of the fixture to carry
electrical currents if any of the fixture wires, wire connections or splices were to become broken, cut or
loose during the mounting or normal operation of the fixture. Under this condition, anyone coming in
contact with the fixture would be subject to electrical shock, which could cause serious injury or death.
• DO NOT connect the bare or green insulation fixture ground wire to the black (HOT) current-carrying
wire or the white (NEUTRAL) house wire. Connection of the bare or green fixture ground wire to the
black or white house wires may cause metal parts of the fixture to carry electrical currents. Under this
condition, anyone coming in contact with the fixture will receive electrical shock, which could cause
serious injury or death.
• DO NOT damage or cut the wire insulation (covering) during installation of fixture. DO NOT permit wires
to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which
could cause serious injury or death from electrical shock.
WARNING
•All electrical connections must be in agreement with local codes and ordinances, the National Electric
Code (NEC) and ANSI/NFPA 70-1999. Contact your municipal building department to learn about your
local codes, permits and/or inspections. Risk of fire - most dwellings built before 1985 have supply wire
rated for 140°F. Consult a qualified electrician before installation.
•To avoid personal injury, the use of gloves may be necessary while handling fixture parts with sharp
edges.
•DO NOT suspend any fixture by the house wires.A fixture must always be mounted directly to an outlet
box or to a mounting plate which is first attached to the outlet box. Wire connectors will not support the
weight of a fixture. Suspending a fixture by the house wires and wire connectors will result in the fixture
falling, with the possibility of personal injury and the danger of electrical shock or fire.
•To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this light
fixture are designed to accept only one 12-gauge house wire and two lead wires from the light fixture. If
your house wire is larger than 12-gauge or there is more than one house wire to connect to the
corresponding fixture lead wires, consult an electrician for the proper size wire connectors to use.
• Failure to caulk fixture mounting surface with silicone weather sealant may result in water damage in
outlet box, which may cause electrical malfunction or electrical shock.

5
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to install,
operate or assemble the product.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): Flathead Screwdriver, Phillips Screwdriver, Wire
Strippers, Pliers, Wire Cutters, Safety Glasses, Stepladder, Electrical Tape, Silicone Weather Sealant
Helpful Tools (not included): A/C Tester Light, Do-It-Yourself Guide, Soft Cloth
PREPARATION
• NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
SAFETY INFORMATION
CAUTION
• TURN OFF ELECTRICITY at main fuse box (or circuit breaker box) before beginning installation by
removing the fuse (or switching the circuit breaker off).
• If you are not sure the lighting system has a grounding means, DO NOT attempt to install this fixture.
Contact a qualified, licensed electrician for information regarding the proper grounding methods as
required by the local electrical code in your area.
• All fixtures must be mounted to an outlet box that is supported by the building structure.
• To avoid water damage to fixture or possible electrical malfunction, install fixture at least 4 ft.
above the ground/floor.
• Do NOT tamper with or attempt to repair LED component of fixture. The light source is designed for
this specific application and should not be serviced by untrained personnel. If any servicing is
required, call our customer service department.

6
ASSEMBLY INSTRUCTIONS
ON
OFF
ON
OFF
Turn off circuit breakers and wall switch to the
fixture supply line leads.
DANGER: Failure to disconnect power
supply prior to installation may result in
serious injury or death.
1
1.
Remove existing fixture and disconnect all
electrical wiring.
2. 2
Outlet Box
Remove decorative nuts (D) and washers (C) from
front of fixture (A) and remove mounting strap (B)
from back of fixture (A). Save decorative nuts (D)
and washers (C) for later use.
3.
A
B
D
C
3
D
C

7
ASSEMBLY INSTRUCTIONS
Adjust screws (F) to proper length by screwing
them completely into mounting strap (B).
Temporarily place fixture (A) over mounting strap
(B) to determine amount of adjustment necessary
for screws (F). [NOTE: Screws (F) should come
through holes in fixture (A) just enough so
decorative nuts (D) fit flush against fixture (A) when
mounted.] Once screws (F) are adjusted, use pliers
(not included) to tighten nuts (E) on screws (F)
securely against mounting strap (B).
Set fixture (A) aside.
5. 5Outlet Box
B
A
FE
Outlet Box
FB
4
4.
Crossbar
Washer
BB
Hardware Used
Machine Screw x 2
BB
D
Attach mounting strap (B) to outlet box (not
included) using the existing washers and outlet
box screws or the machine screws (BB). NOTE:
If the outlet box screws required for your outlet
box are of a different size than the machine
screws (BB), consult with a licensed electrician
before proceeding.
Tighten machine screws (BB) completely to
secure mounting strap (B) to outlet box.
Turn crossbar on mounting strap (B) so that
screws (F) are level horizontally. [Use a level (not
included) to adjust screws (F) parallel with floor
and ceiling as needed.] Tighten set screw,
located in the middle of the mounting strap (B), to
secure crossbar.
CAUTION: The fixture must be mounted to
an outlet box that is supported by the building
structure. Plastic outlet boxes are not
recommended.

8
ASSEMBLY INSTRUCTIONS
Unwrap BARE wire from BLACK and WHITE wires
on fixture (A). Prepare wire by stripping 3/4 in. of
insulation from wire ends using wire strippers (not
included).
6a
6a.
6b. Connect BARE/GREEN ground wire from outlet
box to BARE wire from fixture (A) using wire
connector (AA). Connect WHITE wire from fixture
(A) to WHITE wire from outlet box using wire
connector (AA). Connect BLACK wire from fixture
(A) to BLACK wire from outlet box using wire
connector (AA).
NOTE: Screw wire connectors (AA) on in a
clockwise direction.
WARNING: Never connect BARE/GREEN
ground wire to WHITE or BLACK power supply
wires.
WARNING: To reduce the risk of fire, electrical
shock or personal injury, wire connectors (AA)
provided with this light fixture are designed to
accept only one 12-gauge house wire and two lead
wires from the light fixture. If your house wire is
larger than 12-gauge or there is more than one
house wire to connect to the corresponding fixture
lead wires, consult an electrician for the proper size
wire connectors to use.
Wire Connector
Wrap electrical tape (not included) around each
individual wire connector (AA) down to the wire.
WARNING: Make sure no bare wire or wire
strands are visible after making connections.
Carefully arrange excess wiring and wire
connectors (AA) within outlet box.
7.
x 3
Hardware Used
AA
7
Outlet
Box
AA
AA
6b
Outlet
Box
WHITE
BLACK
BARE/GREEN
AA
A
AA
BARE
AA
AA

8. 8
F
After completing installation, caulk fixture (A)
mounting surface with silicone weather sealant
(not included).
WARNING: Failure to caulk fixture mounting
surface with silicone weather sealant may result
in water damage in outlet box, which may cause
electrical malfunction or electrical shock.
9.
A
D C
F
ASSEMBLY INSTRUCTIONS
10.
Restore power and test fixture (A).
If light does not function, please refer to
TROUBLESHOOTING on the next page.
9
B
Align holes in fixture (A) with screws (F) on
mounting strap (B) and push fixture (A) toward
wall. Attach fixture (A) to mounting strap (B)
using the washers (C) and decorative nuts (D)
previously removed (Step 3, page 6).
9
A
10
A
DC

CARE AND MAINTENANCE
•Shut off main power supply. Wipe fixture with soft, damp cloth. Use window cleaner to clean glass.
Do not use an abrasive cleaner on glass or fixture.
• Total wattage for WLL103BZ is 7.8 watts. Do not attempt to replace the LED.
• Total wattage for WLL104BZ is 10.5 watts. Do not attempt to replace the LED.
OPERATING INSTRUCTIONS
TROUBLESHOOTING
WARNING: Before beginning work, shut off the power supply to avoid electrical shock.
Fuse blows out or
circuit breaker trips. 1. Crossed wires.
2. Power wire is grounding out. 1. Check wiring. 2. Check all connections.
1. Make sure power supply is ON.
2. Check wiring and all connections.
3. Contact customer service.
4. Cap sensor or wait until dark.
5. Remove sensor cap.
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Light does not come
on initially or no longer
comes on.
1. Power is OFF.
2. Faulty connection.
3. LED component is not
working properly.
4. Sensor is inactive.
5. Sensor cap is on.
This fixture can function with either the wall
switch or the preassembled dusk-to-dawn
sensor (G). To activate the dusk-to-dawn
capability, remove the sensor cap (H) from
sensor (G).
NOTE: For the fixture to work properly, the wall
switch to the fixture MUST be turned ON atALL
times.
1. 1G
10
H