Portwell WEBS-5482-W User manual

WEBS-5482-W
Fan-less Embedded System
User's Manual
Version 1.0
Copyright © Portwell, Inc., 2015. All rights reserved.
All other brand na es are registered trade arks of their respective owners.

Preface
Table of Contents
How to Use This Manual
Chapter 1 System Overview.......................................................................................................1-1
1.1 Introduction ....................................................................................................... 1-1
1.2 Check List ........................................................................................................... 1-2
1.3 Product Specification ........................................................................................ 1-2
1.4 Mechanical Di ension ..................................................................................... 1-3
Chapter 2 System Installation....................................................................................................2-1
2.1 HDD Installation ............................................................................................... 2-1
2.2 CFEX Installation .............................................................................................. 2-2
2.3 PCIe/PCI Card Installation ............................................................................. 2-2
2.4 I/O Interfaces .................................................................................................... 2-4
2.4.1 Front View ................................................................................................. 2-4
2.4.2 Rear View .................................................................................................. 2-5
2.5 Getting Started ................................................................................................... 2-7
Chapter 3 BIOS Setup Information............................................................................................3-1
3.1 Entering Setup – Launch Syste Setup ......................................................... 3-1
3.2 Main .................................................................................................................... 3-2
3.3 Syste Setup Utility ......................................................................................... 3-3
3.4 Configuration .................................................................................................... 3-3
3.5 Boot ................................................................................................................... 3-22
3.6 Security ............................................................................................................. 3-24
3.7 Exit ..................................................................................................................... 3-25
Chapter 4 Important Instructions ..............................................................................................4-1
4.1 Note on the Warranty ....................................................................................... 4-1
4.2 Exclusion of Accident Liability Obligation ................................................... 4-1
4.3 Liability Li itations / Exe ption fro the Warranty Obligation............ 4-1
4.4 Declaration of Confor ity ............................................................................... 4-1
Chapter 5 Frequent Asked Questions.......................................................................................5-1

Preface
How to Use This Manual
The anual describes how to configure your WEBS-5482-W syste to eet various
operating require ents. It is divided into five chapters, with each chapter addressing
a basic concept and operation of Fan-less E bedded Syste .
Chapter 1: System Overview. Present what you have in the box and give you an
overview of the product specifications and basic syste architecture for this fan-less
e bedded syste .
Chapter 2: System Installation. Show the definitions and locations of all the
interfaces and describe a proper installation guide so that you can easily configure
your syste .
Chapter 3: BIOS Setup Information. Specify the eaning of each setup para eters,
how to get advanced BIOS perfor ance and update new BIOS. In addition, POST
checkpoint list will give users so e guidelines of trouble-shooting.
Chapter 4: Important Instructions. Indicate so e instructions which ust be
carefully followed when the fan-less e bedded syste is used.
Chapter 5: Frequent Asked Questions. Provide the answers for the ost frequently
asked questions.
The content of this anual is subject to change without prior notice. These changes
will be incorporated in new editions of the docu ent. The vendor ay ake
supple ent or change in the products described in this docu ent at any ti e.

System Overview
WEBS-5482-W User’s Manual 1-1
Chapter 1
System Overview
1.1 Introduction
Portwell, a world-leading innovator in the industrial PC (IPC) industry and a
Pre ier Me ber of the Intel® Internet of Things (IoT) Solutions Alliance, announces
WEBS-5482-W, a high perfor ance and low power intelligent Box PC. Powered by
the 4th generation Intel® Core™ ULT (ultra low TDP) SoC (syste on chip) processor
(for erly codena ed Haswell), this syste is an ideal fan-less controller for
applications in digital signage, surveillance, i age processing and achine
auto ation industries.
The Portwell WEBS-5482-W is powerful but not power hungry; it utilizes the
dual-core 4th generation Intel® Core™ processor with Intel® Turbo Boost
Technology 2.0 (select CPU SKUs), Intel® Hyper-Threading Technology and
Enhanced Intel SpeedStep® Technology. By adopting Intel’s SoC platfor , which
integrates CPU and PCH into a BGA package, WEBS-5482-W is uch functional
co pared to its previous generation. In addition, the eli ination of the 2-chip
platfor enables a ore effective ther al design for the WEBS-5482-W intelligent
Box PC. Thanks to the highly reliable chassis with a ther ally-enhanced ripple fin
design, WEBS-5482-W can operate reliably in a te perature range fro -20℃ to 55℃.
Plus, co bining anti-vibration and shock resistance attributes, the fan-less and
rugged WEBS-5482-W excels in harsh environ ents.
WEBS-5482-W also offers clear and concise video and graphics capabilities because
it takes full advantage of the 4th generation Intel® Core™ processor with integrated
HD4400 graphics engine which outperfor s its predecessor by over 20%. Product
reliability and stability are definitely unco pro ised; WEBS-5482-W is rated IP40
and certified by industrial product quality tests, such as an anti-vibration test of up to
5Gr s and an anti-shock test of 50G. Portwell’s WEBS-5482-W has proven itself to be
a perfect solution for video/graphics-de anding and auto ation control syste s.
The versatile WEBS-5482-W syste supports any other i portant features,
including up to 16GB of DDR3L e ory, triple display with DVI-D, HDMI and
Display Port and dual Intel® Gigabit Ethernet ports. It also offers rich co pact I/O
functions including 1 x SATA, 2 x USB 3.0, 2 x USB 2.0 and 4x COM ports. To enhance
syste flexibility, custo ers can further aug ent functions per their specific needs
via two antenna interfaces and an onboard SIM card holder for WiFi or 3G/GPS
odule, two ini PCIe sockets and 1 x PCIe slot for expansion; one or ore PCIe
expansion cassettes can be offered by counterparts of WEBS-5482-W for hungry
de and. A wide range of DC power input, 12V~24V, is accepted so that it can not
only prevent the syste fro da age due to power input change, but also expands
the application fields of this Box PC to the auto otive industry, for exa ple. This

System Overview
WEBS-5482-W User’s Manual 1-2
power-source flexibility enables product usage in a variety of situations. Moreover,
the WEBS-5482-W is ore than a robust and dependable Box PC syste with high
perfor ance and graphics efficacy. Its stylish echanical design enhances the
syste ’s artistry. Potential applications include POS, kiosk and digital signage and
transportation, etc.
1.2 Check List
The WEBS-5482-W package should cover the following basic ite s:
One WEBS-5482-W Fan-less E bedded Syste
One 96W AC/DC Power Adapter DC-plug with screw
One Wall Mount Kit
Other Accessories
If any of these ite s is da aged or issing, please contact your vendor and keep all
packing aterials for future replace ent and aintenance.
1.3 Product Specification
System
M/B PEB-5731-W
Syste Chipset Intel® Haswell ULT SoC
CPU Intel® Core™ i7-4650U,
1.7GHz, 4M L2 Cache, up to 3.3GHz, 15W TDP (2C/4T)
Intel® Core™ i5-4300U,
1.9GHz, 3M L2 Cache, up to 2.9GHz, 15W TDP (2C/4T)
Intel® Core™ i3-4010U,
1.7GHz, 3M L2 Cache, 15W TDP (2C/4T)
Intel® Celeron 2980U,
1.6GHz, 2M L2 Cache, 15W TDP (2C/2T)
BIOS AMI uEFI BIOS (SPI ROM)
Syste Me ory Dual 204-pin SO-DIMM sockets support DDR3L 1333/1600
up to 16GB
Storage 1x 2.5” SATA HDD/SSD, 1x CFEX, 1x SATA
Watchdog Ti er Progra able via S/W fro 1 sec. to 255 sec.
H/W Status Monitor -Te perature (CPU & Syste )
-Voltage (CPU Vcore, VBAT, 5VSB, 12V, 5V, 3.3V)
Expansion -1x Full-size Mini-PCIe socket (USB+PCIe) + SIM holder
-1x Half-size Mini-PCIe socket ( SATA+PCIe)
-1x PCIe x4 slot (PCIe x1 signal)
External I/O
Series Ports 4x COM Ports
(1x RS-232/422/485 selectable by BIOS & 3x RS-232)
Display 1x DVI-D, 1x DP, 1x HDMI
USB 2x USB 3.0, 2x USB 2.0

System Overview
WEBS-5482-W User’s Manual 1-3
Audio N/A
LAN 2x Gigabit Ethernet (Intel® WGI218LM + WGI210AT)
GPIO N/A
Other -2x Antenna holes for WIFI or 3G/GPS odule
Power Supply Unit
Power Supply DC 12~24V
Environment
Operating
Te perature -20℃ to 55℃
Storage Te perature
-40℃ to 80℃
Relative Hu idity 95% @ 40℃, non-condensing
Operating Vibration 5Gr s/5~500Hz, IEC 60068-2-64
Operating Shock 50G, 11 sec, IEC 60068-2-27
Mechanical
Di ension (WxDxH) 255 x 187 x 86 ; 10” x 7.3” x 3.3”
Weight 5 kg
Mounting Wall Mount
1.4 Mechanical Dimension
Front view of the WEBS-5482-W syste
Rear view of the WEBS-5482-W syste

System Overview
WEBS-5482-W User’s Manual 1-4
Top view of the WEBS-5482-W syste
Side view of the WEBS-5482-W syste

System Installation
WEBS-5482-W User’s Manual 2-1
Chapter 2
System Installation
This chapter provides you with instructions to set up your syste . Definitions
and locations of all the interfaces are described so that you can easily configure
your syste . For ore detailed PIN assign ent and ju per setting, please refer
to user’s anual of PEB-5731-W.
2.1 HDD Installation
HDD cover locates at the front of the syste .
Step 1. Loosen the thu bscrews of the
HDD cover
Step 2. Draw out the HDD tray fro
the syste
Step 3. Install the HDD into tray with
screws
Step 4. Push the HDD tray back
Step 5. Tighten the thu bscrews and
finish installation

System Installation
WEBS-5482-W User’s Manual 2-2
2.2 CFEX Installation
CFEX is a new Co pact Flash (CF) technology initiated by Portwell and adapting
legacy CF type one with advanced pin definitions. This helps overco e reliability
issues with standard co ercial e ory. CFEX also supports SATA 3.0, SPI and
other extensions, and achieves a read speed of 100 to 120Mbyte/s and write speed
of 45 to 75Mbyte/s. Co pared with other CF devices, it falls in the sa e low-cost
bracket as CF and CF SATA and is less expensive than CFAST.
Step 1. Unscrew the CFEX cover Step 2. Take the CFEX card
Step 3. Insert the CFEX card into the
slot
Step 4. Finish installation
2.3 PCIe/PCI Card Installation
Equipped with an innovative PCI/PCIe expansion odule, user can easily install
and replace their own expansion cards.
Step 1. Loosen the back cover 2 screws
of the expansion odule
Step 2. Prepare the hex screwdriver
which in the accessory box
Step 3. Loosen the side cover 2 screws of
the expansion odule by the hex
screwdriver
Step 4. Carefully detach the odule
fro the ain syste

System Installation
WEBS-5482-W User’s Manual 2-3
Step 5. Loosen the screw of the
expansion odule
Step 6. On the back side, loosen the 3
screws of the expansion odule
Step 7. Install the expansion card via the
PCIe x4 slot
*Note: I age of the expansion card is
for reference only.
Step 8. Screw the expansion card
Step 9. Install the odule back to the
syste and screw it
Step 10. Finish the installation
Add-on card dimension limitation:
Max di ension of add-on card in WEBS-5482-W is 157 x 111 .

System Installation
WEBS-5482-W User’s Manual 2-4
2.4 I/O Interfaces
2.4.1 Front View
A T1 & A T2 hole:
Antenna holes for WiFi or 3G/GPS odule
2.5" HDD/SSD Tray:
One re ovable 2.5" HDD/SSD trays for storage installation

System Installation
WEBS-5482-W User’s Manual 2-5
2.4.2 Rear View
Power Button:
Press the power button to turn ON/OFF the syste
CFEX:
CFEX is a new Co pact Flash (CF) technology initiated by Portwell and adapting
legacy CF type one with advanced pin definitions. This helps overco e reliability
issues with standard co ercial e ory. CFEX also supports SATA 3.0, SPI and
other extensions, and achieves a read speed of 100 to 120Mbyte/s and write speed
of 45 to 75Mbyte/s. Co pared with other CF devices, it falls in the sa e low-cost
bracket as CF and CF SATA and is less expensive than CFAST.
USB3.0 & USB 2.0:
Support four USB (Universal Serial Bus) ports including two USB 3.0 and two
USB 2.0.
HDD Led:
Shows real-ti e read and write activity of your HDD/SSD as a s all blinking
indicator
Reset Button:
Press the Reset button to turn reset the syste
LA :
Two Gigabit Ethernet (10/100/1000 Mbits/sec) LAN ports by using Intel
WGI218LM & WGI210AT GbE Ethernet Controller
HDMI:
Type A HDMI display output
DP:
DP (DisplayPort) display output

System Installation
WEBS-5482-W User’s Manual 2-6
DVI-D:
DVI-D display output
DC in: (Wide range DC source support, 12~24V)
Using the provided DC source to connect to the syste
COM port:
RS-232/422/485 – COM1
*Note: RS-232/422/485 configuration is deter ined by BIOS setting.
Check BIOS setting for details.
PI o. Signal Description
1 DCD#/DT-
2 RXD#/DT+
3 TXD#/422R+
4 DTR#/422R-
5 GND
6 DSR#
7 RTS#
8 CTS#
9 RI#
RS-232 – COM2, COM3, COM4
PI o. Signal Description
1 DCD#
2 RXD#
3 TXD#
4 DTR#
5 GND
6 DSR#
7 RTS#
8 CTS#
9 RI#

System Installation
WEBS-5482-W User’s Manual 2-7
2.5 Getting Started
It is easy to get the syste started.
Step 1. Make sure the power supply
(12~24V) is connected properly
* ote: Please connect the power
supply only either “Terminal block”
or “DC Adaptor”. Don’t connect to
both at the same time.
Step 2. Press the power button to turn
on the syste
*Note: Power LED shines BLUE when
syste is “ON”; ORANGE when “OFF”

BIOS Setup Information
WEBS-5482-W User’s Manual 3-1
Chapter 3
BIOS Setup Information
WEBS-5482-W syste adopts PEB-5731-W other board. PEB-5731-W uses AMI
BIOS structure stored in Flash ROM. These BIOS has a built-in Setup progra
that allows users to odify the basic syste configuration easily. This type of
infor ation is stored in CMOS RAM so that it is retained during power-off
periods. When syste is turned on, PEB-5731-W co unicates with peripheral
devices on the carrier board and checks its hardware resources against the
configuration infor ation stored in the CMOS e ory. If any error is detected,
or the CMOS para eters need to be initially defined, the diagnostic progra will
pro pt the user to enter the SETUP progra . So e errors are significant enough
to abort the start up.
3.1 Entering Setup – Launch System Setup
Power on the co puter and the syste will start POST (Power On Self Test)
process. When the essage below appears on the screen, press <DEL> key will
enter BIOS setup screen.
Press <DEL> to enter SETUP
If the essage disappears before responding and still wish to enter Setup, please
restart the syste by turning it OFF and On or pressing the RESET button. It can
be also restarted by pressing <Ctrl>, <Alt>, and <Delete> keys on keyboard
si ultaneously.

BIOS Setup Information
WEBS-5482-W User’s Manual 3-2
3.2 Main
Use this enu for basic syste configurations, such as ti e, date etc.
Build Time, Processor Brand ame, Processor Speed, Install Memory, etc
These ite s show the fir ware and e ory specifications of your syste .
Build Time
The BIOS Release Date.
Processor Brand ame / Processor Speed
This value will change depend of different CPUs. And please ake sure the
Processor that you’ll install will be co patible with PEB-5731-W User’s Manual
System Date
The date for at is <Day>, <Month> <Date> <Year>. Use [＋] or [－] to configure
syste Date.
System Time
The ti e for at is <Hour> <Minute> <Second>. Use [＋] or [－] to configure
syste Ti e.
Access Level

BIOS Setup Information
WEBS-5482-W User’s Manual 3-3
3.3 System Setup Utility
To enter the syste setup utility, press <F1> on either the ain keyboard or
Console Redirection host co puter’s keyboard during POST.
Table 1 lists the available enus in the syste setup utility. Each enu is
equivalent to a functional group and consists of all correlated BIOS settings.
Table 1. Syste Setup Utility enus
Menu Usage
Main Display a su ary of the syste and configure the
syste date and ti e.
Configuration
Configure the syste interfaces, syste
anage ent, power anage ent, ther al
anage ent, and other syste characteristics.
Boot Configure boot device priority settings.
Security Configure user authentication require ents.
Save & Exit Save changes and exit the syste setup utility, or
restore default settings.
3.4 Configuration
Use this enu to set up the ite s of special enhanced features.

BIOS Setup Information
WEBS-5482-W User’s Manual 3-4
CPU Configuration
It is not necessary to ake any change just take the default value.
Here you’ll see the Max Processor Speed/Processor Cores/Intel HT technology
then you can adjust if you want to “disabled” the Hyper-threading.
BIOS Ite Usage Ite -Specific Help
Hyper-threading -Disabled
-Enabled ★ Default
Enabled for Windows XP /
Linux and Disabled for other OS
Active Processor Cores -All ★ Default
-1
Select the nu ber of physical
cores to enable in each processor
package
Intel Virtualization
Technology
-Disabled
-Enabled ★ Default
When enabled, a VMM can
utilize the additional hardware
capabilities provided by
Vanderpool Technology
EIST -Disabled
-Enabled ★ Default
Enabled/Disabled Intel
SpeedStep
Turbo Mode -Disabled
-Enabled ★ Default Turbo Mode
CPU C states -Disabled
-Enabled ★ Default CPU C states
Enhanced C1 state -Disabled
-Enabled ★ Default Enhanced C1 state
CPU C3 report -Disabled
-Enabled ★ Default CPU C3 report
CPU C6 report -Disabled
-Enabled ★ Default CPU C6 report

BIOS Setup Information
WEBS-5482-W User’s Manual 3-5
Chipset Configuration
It is not necessary to ake any change just take the default value.
BIOS Ite Usage Ite -Specific Help
High Precision Ti er -Disabled
-Enabled★ Default
Azalia -Disabled
-Enabled★ Default
VT-d -Disabled ★ Default
-Enabled
Enabled/Disabled VT-d
function on MCH
Port 80h Redirection -LPC Bus
-PCIE Bus

BIOS Setup Information
WEBS-5482-W User’s Manual 3-6
AMT Configuration
BIOS Ite Usage Ite -Specific Help
Intel AMT -Disabled
-Enabled ★ Default
Disables/Enabled iAMT
function
Un-Configure ME -Disabled ★ Default
-Enabled
Disable ME -Disabled ★ Default
-Enabled