POSIFLEX XT-5415 User manual

Package Contents
15” fanless LCD IR touch terminal with
Gen 7E or Gen 8E base stand (x 1)
Power adapter (x 1)
Power cord (x 1)
User manual (x 1)
Recovery DVD or Information DVD (x 1)
Product Features
Fanless Design
Intel 4th generation Haswell CPU
New GEN 7E foldable base that allows JIVA XT Series to be configured into
different configurations.
New Gen 8E foldable base that integrates internal power adaptor and powered
USB port into the base stand.
Mini-PCIe expansion slot
Dual LAN Ports
16760901010 Ver. Original
http://www.posiflex.com
XT-5415/5615
Fanless LCD IR Touch Terminal
User Manual
1

Views of the XT-5415/5615 with Gen 7E Base Stand
Front View
Rear View
Side View
Gen 7E Base Stand
XT-5415/5615
LCD IR Touch Panel
Cable Cover
Base Stand Cover
Cable Exit
HDD Cover
Power Button
Brightness Adjustment Button
＋
Brightness Adjustment Button －
LED indicator
2

Bottom View
Views of the XT-5415/5615 with Gen 8E Base Stand
Front View
Rear View
Gen 8E Base Stand
XT-5415/5615
LCD IR Touch Panel
Cable Holder
HDD Cover
Rubber Feet with Fixing Screw
Rubber Feet with Fixing Screw
Cable Exit
Base Stand Cover
Cable Cover
LED indicator
Cable Exit
3

Side View
Bottom View
View of I/O Interface of XT-5415/5615
Rubber Feet with Fixing Screw
Line Out/MIC-In
Combo Jack
USB 2.0
Ports
USB 3.0
Ports
DB9 COM Ports
VGA Port
CR Port
LAN Ports
12V BAT Port
DC IN
Power
Connector
Power Button
Brightness Adjustment Button
＋
Brightness Adjustment Button －
Rubber Feet with Fixing Screw
RJ-50 COM Ports
Power Adapter
Compartment
UPS Battery
Compartment
4

Positioning your POS for a Perfect Viewing Angle
The adjustable base stands designed for XT-5415/5615 come in two models,
Gen 7E/8E, and allow you to determine an ideal position for your terminal
using its unique tilt adjustment mechanism. As the below figures suggest, both
Gen 7E and Gen 8E base stands provide three standard positioning solutions
for your terminal: flat folded mode, low profile mode, and full extended mode.
XT-5415/5615 with Gen 8E Stand Base
Flat folded mode
Low profile mode
Full extended mode
In general, XT-5415/5615 will be set up beforehand in flat folded mode and
then packaged into the box for shipping. After it is unpacked, you may re-
adjust the terminal in either low profile mode or full extended mode according
to your situation. Below will provide instructions on how to adjust the specific
base stand connected to the POS system. As a reminder, please be careful not
to touch the LCD panel while setting up the tilt angle
XT-5415/5615 with Gen 7E Base Stand
Please refer to the following instructions on how to switch among different
positioning modes to find an ideal viewing angle for XT-5415/5615 with
Gen 7E base stand.
1. Unpack XT-5415/5615, which is supposed to
be set in flat folded mode, out of the package
box and then lay your POS system on a flat
surface.
2. Steady the base stand with one hand, and then
tilt the screen downwards.
5

3. Push the cable cover outwards to remove it
from the base stand.
4. Position your terminal in Full Extended mode.
4.1 Support the screen with one hand holding onto its bottom edge. Then,
while pulling the lever backwards, move the display upwards until the
lever is snapped into the hook to raise the screen as shown in the
below figure.
4.2 Push the cable cover back.
4.3 Tilt the screen up or down to your
desired angle. Please do not press on
the LCD panel while setting up the
tilt angle.
Lever
Hook
6

5. Return your terminal back to Flat Folded modefrom Full Extended
mode.
5.1 Tilt your screen in a horizontal position.
5.2 Support the screen with one hand holding onto its bottom edge. While
pulling the lever backwards, move the display downwards until the lever
is lifted off the hook as shown in the figure
5.3 Push the cable cover back.
5.4 Tilt the screen again to the horizontal
position.
Hook
Lever
7

6. Position the terminal in Low Profile mode. In most cases, if you attempt
to set up the terminal in low profile mode, it is strongly advised to place
the terminal high enough so that the screen would not hit the table when
being tilted.
6.1 Follow Step 5 to set up the termimal in
Flat Folded mode.
6.2 Tilt the screen all the way down
6.3 To tilt screen up or down to your desired
angle, please be advised to keep the base
stand steady with one hand to do so. Do
NOT press on the LCD panel while
setting up the tilt angle.
XT-5415/5615 with Gen 8E Base Stand
Please refer to the following instructions on how to switch among different
positioning modes to find an ideal viewing angle for XT-5415/5615 with
Gen 8E base stand.
1. Unpack XT-5415/5615, which is supposed
to be set in flat folded mode, out of the
package box and then lay your POS system
on a flat surface.
2. While steadying the terminal with your
hand holding onto the base stand, tilt the
screen down.
8

3. Push the cable cover outwards to remove it
from the base stand.
4. Position your terminal in Full Extended mode.
4.1 Support the screen with one hand holding onto its bottom edge. Then,
while pulling the lever backwards, move the display upwards until the
lever is snapped into the lower hook to raise the screen as shown in
the below figure.
4.2 Push the cable cover back.
4.3 Tilt the screen up or down to your
desired angle. Please do not press on
the LCD panel while setting up the tilt
angle.
Lower
hook
Lever
9

5. Position the terminal in Low Profile mode. While setting up the
terminal in low profile mode, ensure that the terminal is placed high
enough so that the screen would not hit the table surface.
5.1 While keeping your terminal steady
with your hand holding on to the
base stand, tilt your terminal down.
5.2 Support the screen with one hand holding onto its bottom edge.
Then, while pulling the lever backwards, move the display upwards
or downwards until the lever is snapped into the upper hook to
lower the screen as shown in the below figure.
5.3 Push the cable cover back.
5.4 Tilt the screen up or down to your
desired angle. Please do not press on
the LCD panel while setting up the
tilt angle.
Lever
Upper
hook
10

6. Return the terminal back to Flat Folded mode.
6.1 While steadying your terminal with your
hand holding onto the base stand, tilt
your screen up.
6.2 Support the screen with one hand holding onto its bottom edge.
While pulling the lever backwards, release the lever back to the
point above the upper hook as shown in the figure.
6.3 Push the cable cover back.
6.4 Tilt the screen to the horizontal position.
Lever
11

Routing and Arranging Cables
Each base stand features its own cable management to help you well organize
the cords whenever you need to connect peripheral devices to XT-5415/5615.
Based on different base stands, the following provides some useful cable-
routing instructions required to manage your cables.
For Gen 7E Base Stand
1. Lay the terminal with its rear facing
towards you and tilt the screen all the way
down.
2. Remove the cable cover.
3. Pull outwards the locking levers with your
forefingers and then remove the cover in
the direction shown by the arrow.
4. Positon your terminal with the bottom
facing you. Then, pass the cord through the
cable exit from the bottom side.
5. Place the terminal with the rear facing
towards you. After tilting the screen to the
horizontal positon, route the cable along the
cable passage and through the cable exit.
Cable Exit
Cable Exit
12

6. Tilt the terminal up enough to have the bottom I/O plate towards
you. Locate the cable arrangement cover as shown in the figure.
7. Remove the cable arrangement cover by
pushing it up in the direction shown by the
arrow.
8. Properly insert the cable into the correct
port on the bottom I/O plate.
9. Neatly arrange your cable. Then, make sure
the cord can be held into place and passed
through the cable exit after sliding back the
cable arrangement cover.
10. Have the screen tilt all the way down, and
then push the base stand cover back into
place.
11. Place the cable cover back.
Cable Exit
Cable Arrangement Cover
13

For Gen 8E Base Stand
1. Set up your terminal in Full Extended mode
and then tilt the screen all the way down.
2. Remove the cable cover at the rear of the
terminal.
3. Pull outwards the locking levers with your
forefingers and then remove the cover in the
direction shown by the arrow.
4. Tilt the screen to the horizontal position.
Thread the cables along the cable passage
and then through the cable exit.
5. Tilt the terminal up enough to have the bottom I/O plate towards you.
Locate the cable arrangement cover as shown in the figure.
6. Remove the cable arrangement cover by
pushing it up in the direction shown by the
arrow.
Cable exit
Cable Arrangement Cover
14

7. Connect the cable to the I/O ports of the
terminal.
8. Neatly arrange your cable. Then, make sure
the cord can be held into place and passed
through the cable exit after sliding back the
cable arrangement cover.
9. Tilt the screen all the way down. Then, push
the base stand cover back into place.
10. Put the cable cover back.
11. If you are routing the cables of external
peripherals, please make sure the cable is
threaded though the cable exit at the bottom
of the base stand.
Installing Optional Upgrade Kits and Peripherals
XT-5415/5615 is an expandable model which allows you to upgrade its own
capacity by additionally installing multiple peripheral devices, such as
magnetic stripe reader (MSR), LCD monitor and cash drawer, according to
your preference. The following will give you installation instructions on how
to expand on your current POS system with these optional upgrade kits. Before
proceeding with the installation of peripherals, please make sure the POS
system is completely shut down to prevent damage.
Cable exit
Cable Exit
15

Installing Power Adapter to Gen 8E Base Stand
Power adapter is used to provide power which your terminal needs to be
operated normally. Please go through the below steps to install the power
adapter into Gen 8E base stand. If the power adapter is already installed
to Gen 8E base stand, you may skip this section
1. Lay your POS terminal on a flat surface
with its bottom facing towards you.
2. Take the AC power adapter with its
rubber feet facing you. Place the bottom
side of the power adapter into the
bottom of the power adapter
compartment first, and then push it
down into place.
3. Place two brackets separately on the top
and bottom sides of the power adapter
compartment as shown in the figure.
Then, fasten two brackets with four
fixing screws.
4. Before threading the cable through the cable exit, loosen two fixing
screws for the bracket of the middle compartment. Then, slide the
bracket in the direction shown by the arrow to remove the bracket for
the middle compartment.
Bracket
16

5. Pass the cable of the power adapter
through the cable exit and then connect
it to the port on the I/O plate of your
POS system. (Please refer to Routing
and Arranging Cables section to thread
the cable, according to the model of
your base stand.)
6. Neatly thread the cord along the bottom
edge of the middle compartment (1), and
then use the cable tie to hold the extra
cable (2) as shown in the figure.
7. Place back the middle compartment
bracket into place, and then secure it
using two fixing screws.
8. Lay the POS terminal on a flat surface
with its rear facing towards you. Then,
connect the female end of power cord to
the power adapter and the other end to
the electrical outlet.
10. To hold the power cord into place, attach the screw hole of power
adapter holder to the hole at the bottom of Gen 8E base stand,
and then use a fixing screw to secure the bracket.
Cable tie
(1)
(2)
Power Adapter
Holder
Cable Exit
17

Installing UPS Battery to Gen 8E Base Stand
UPS battery compartment can be found
at the bottom of Gen 8E base stands as
shown in the figure. Please be advised
that the installation of UPS battery
should be conducted by a technician
according to the user manual specific to
UPS battery.
Installing Side Mount Upgrade Kits
Located at left side on the back of your
LCD panel, side mount compartment is
mainly used for installation of side-
mounted equipment, such as magnetic
stripe reader. For detailed installation
instructions, please refer to the user
manual specific to the device which you
intend to mount onto the terminal.
Installing Rear Top Mount Upgrade Kits
Rear top mount upgrade kits, including
customer pole displays and monitors, have
to be mounted onto the top side on the rear
of your POS terminal as shown in the
figure. As for the installation instructions
along with the individual cable
arrangement for the specific stand base,
please be advised to read the user manual
specific to the device you intend to install.
Installing Wall Mount Kits
The wall mount kits enable you to mount your POS terminal onto the
wall as an alternative. For detailed installation instructions, please be
advised to refer to the user manual specific to wall mount kits.
Installing an Operating System
You are highly advised not to install an operating system on XT-5415/5615
without professional instructions. Not only might the careless handling during
installation cause irreversible damage to your machine, but also the improper
installation likely leads to system malfunction or failure. Please contact with
your dealers about the issues of operating system installation.
18

Performing System Recovery
For XT-5415/5615 models with preloaded operating systems, Recovery DVD
which includes useful utilities will be provided in the package to assist you in
efficiently restoring or repairing your damaged system. However, you are not
encouraged to recover your system without the help of system integrators.
Please be advised to contact your service center for further assistance with
system recovery.
Operation Environment
To prevent XT-5415/5615 from overheating, it is suggested to position your
terminal in a well-ventilated working environment. In doing so, please be
advised to keep the POS terminal at least 25mm away from other devices to
ensure the machine is properly cooled down and functioning normally.
Powering ON/OFF the XT-5415/5615
Power ON the XT-5415/5615
Press down the power button for at least 3 seconds to
power on the POS.
Power OFF the XT-5415/5615
In most cases, press the power button of the POS to
power the system off. If the terminal fails to turn off
the machine for unknown reasons, please be advised
to hold the power button more than 10 seconds to
force a shutdown of the system.
Status LED Indicator
LED status indicator, which is located at the bottom edge of the LCD panel, is
mainly responsible for notifying users of the current system status by emitting
various LED signals. In the chart provided below, it describes all the possible
LED status as a quick reference.
LED Status
System
status
AC power
supply
UPS
Battery
Description
Off
OFF
OFF
Unavailable
System power OFF
Off
OFF
OFF
Available
System power OFF
Green
OFF
ON
N.A.
System standby
Blue
ON
ON
N.A.
System power ON
Blinking blue
ON
OFF
Available
System running on
UPS battery
Blinking green
ON
OFF
Available
UPS battery low
Power
Button
19

Specifications
XT-5415
XT-5615
CPU
Intel Celeron 2.7GHz,
2M Cache; Intel
Pentium 2.3GHz, 3M
Cache; Intel Core i3
2.4GHz, 4M Cache
Intel Core i5-4570TE /
2.7GHz up to 3.3GHz / 4M
Cache; Intel Core i7-
4770TE / 2.3GHz up to
3.3GHz / 8M Cache
System Memory
DDR3 1333 SO-DIMM x 2, max. 16GB
Storage Device
SATA Storage x 2,
factory default 320GB
HDD x 1
SATA Storage x 2, factory
default 320GB SATA HDD
x 2
RAID Function
N/A
Yes
Power Supply
12V / 130W
OS Support
Windows 7 / POSReady 7 / Windows Embedded 8.1
Industry / Linux per request
LCD Display
15" TFT LCD
LCD Resolution
1024 x 768
Touch Function
IR touch
Serial Port
6, DB9 x 2 + RJ45 x 2 on I/O plate, pin header x 2
from service window, 5V support on all COM ports,
12V support on COM 1 to COM 4
Parallel Port
1, via optional conversion cable
Standard USB Port
6
Powered USB
Optional 24V x 1 + 12V x 3 via GEN8E base
LAN Port
10 / 100 / 1000 Mb x 2
VGA Port
VGA x 1, 12V support for Posiflex monitors
CR Port
1, control 2 CR via optional Y-cable
UPS Port
Yes
Audio
Internal 2W speaker x 1 + Line-out
Extension Slot
mini-PCIe slot x 1
Built-in WIFI
Optional mini-PCIe WIFI module
Dimension
372 x 320 x 252.7 (W x D x H in mm)
Weight (N. W. in
kg)
5.86
Operating
Condition
0°C - 40°C, 20%RH - 90%RH (Equipped with HDD);
0°C - 50°C, 20%RH - 90%RH (Equipped with SSD)
Storage Condition
-20°C - 70°C, 10%RH - 90%RH
20