POSIFLEX TM-7117E User manual

1
Package Contents
17” TM/LM-7117E
Standalone Monitor……………….(x 1)
VGA Cable………………………..(x 1)
USB type A to B cable...……….....(x 1)
Power Cord………………………..(x 1)
12V/40W Power Adapter………....(x 1)
User Manual………………………(x 1)
Product Features
17” TFT LCD panel
LCD resolution up to 1280 x 1024
5-wire resistive or IR touch panel for TM-7117E
Easy tilt angle adjustment from 15˚to 70˚
2 x USB port support
Optional side attachment support (SD-466Z or KP-300W)
Optional VESA mounting kit (WB-6000V-B)
Dimension : 401 mm (H) x 385 mm (W) x 286 mm (D);
Weight : 6.82 kg
19630902010 Ver. Original
http://www.posiflex.com
TM/LM-7117E
Standalone POS Monitor
User Manual

2
Views of the TM/LM-7117E
Front View
Rear View
Bottom View
Side Mount Cover
Release Button
Cable Exit
17”LM-7117E LCD Panel
17”TM-7117E Resistive or IR Touch Panel
LED Indicator
Cable Holder
Cable Groove
Rubber Feet with Fixing Screw
Cable Passage
Gen 5 Base
Cable Cover
Rubber Feet with Fixing
Screw

3
Left-Side View
Right-Side View
I/O Ports
VGA Port
USB (Type B) Port
DC-IN Power Jack
USB (Type A)
Port
OSD button
EXT button
＋button
－button
Tilt Adjustment Lever
OSD Control Button
Power button

4
Positioning your monitor for a Perfect Viewing Angle
Follow the below steps to adjust the viewing angle for TM/LM-7117E with
Gen5 base stand using the tilt adjustment lever.
1. After pushing down the tilt adjustment lever on
the right side of the stand, tilt the screen up or
back to your desired angle.
2. Release the adjustment lever to lock the LCD
panel into place.
Connecting VGA and USB Cables
Gen5 base features its own cable management to help you well organize the
cords. The following will provide some useful cable-routing instructions for
you to connect VGA and USB cables to TM/LM-7117E.
1. To release LCD panel from Gen5 base, support your monitor with one
hand holding to the bottom of the panel and then push it up while
pressing down the release button located on the back of TM/LM-7117E.
2. Laying Gen5 base stand with its bottom facing
towards you.
Tilt adjustment lever
Release
Button

5
3. Take power adaptor, VGA and USB cables,
and then neatly thread the cables along the
cable groove first, and then snap it into the
cable holder as shown in the figure.
4. Pass the cables through the cable passage.
5. Place Gen5 base in upright position and make
sure the cables can be pulled out of the cable
passage.
6. Lift your monitor to aim four screw bolts on the rear of the monitor to
the four screw holes on the Gen5 base. Then, along the rail slots push
down the monitor until the LCD panel is well locked into place with a
click sound.
7. Connect the monitor to the terminal using VGA cable.
7.1 Connect one end of the VGA cable to
the VGA port at the bottom I/O plate
of your monitor.
7.2 Take the other end of VGA cable to insert it into the VGA port
of your terminal.
Cable groove
Cable holder
Cable passage

6
8. For TM series or LM series with side attachment, please connect the
monitor to the terminal using USB type A to B cable to enable touch
function for your monitor.
8.1 Grab Type-B connector of USB
cable, and then insert it into Type-B
USB port of your monitor
8.2 Properly attach Type-A connector of USB cable to your POS
terminal.
9. To use external sources to supply power to
your monitor, plug power adapter to the DC-In
power jack and then connect its power cord to
electrical outlet.
Powering ON/OFF your Monitor
To start up TM/LM-7117E, you have to make sure that the monitor is well
connected to POS terminals and electricity is supplied to the monitor through
external power sources.
Power ON TM/LM -7117E
Press the power button of the terminal to power up the terminal. Few seconds
later the monitor will be initiated automatically.
Power OFF TM/LM -7117E
After following the standard shutdown procedure to shut down your terminal,
the monitor will be consequently turned off.
Power LED Indicator
Power LED indicator, located at the bottom of the screen, is used to notify
users of the current status of your monitor by emitting various LED signals.
Please refer to the below chart to accurately interpret the of the indicators
status to facilitate your troubleshooting.
Status
Description
ON, solid blue
System power ON
ON, solid green
System Standby
OFF
System power OFF

7
Identifying your Monitor as Secondary Touchscreen Monitor
in Extended Mode
Based on the type of your touch panels, you are required to adopt different
approaches to set up TM series as the extended monitor when you attempt to
extend the desktop across multiple monitors. In the following section the
related descriptions will be offered to help you achieve the purpose.
For TM-7117E Model with Resistive or IR Touchscreen
For TM-7117E users, please follow the below instructions to complete
installation of The Dual Touch Manager, a tool designed to allow your monitor
to work as a secondary touchscreen monitor in extended mode.
1. Make sure that the monitor is well connected to your POS terminal with
USB type A to B cable.
2. Visit Posiflex official site ( http://www.posiflex.com/en-
global/Home/index). Or, you may find USB Dual Touch Manager from
your Posiflex POS terminal instead.
3. Click on Products, which is located on the upper right side of your
browser window. Then, select POS Monitor in the pop-up menu.
4. Select Standalone type of POS monitor. After scrolling down the page,
click on TM-7117E item.
1
2

8
5. Click on the Download tab, and then Drivers & Utility.
6. Click Setup icon of USB Dual Touch Manager to install the USB
Dual Touch Manager.
7. Follow the instructions to complete the manager installation. After the
installation is finished, restart your terminal.
1
2

9
Setting up Display Resolution for Your Monitor
The below chart defines the list of recommended display settings for
TM/LM-7117E. Improper display configuration will prevent the monitor from
properly displaying the image and lead to a warning message of “out of range”
prompted on the screen.
Display
Resolution
Horizontal Frequency
(KHz)
Refresh Rate (Hz)
640 x 400
31.5
70
640 x 480
31.5
60
37.9
72
37.5
75
720 x 400
31.5
70
800 x 600
35.1
56
37.9
60
48.1
72
46.9
75
1024 x 768
48.4
60
56.5
70
60
75
1280 x 1024
64
60
80
75
Using the OSD Menu
OSD, as known as On-Screen Display, is employed to assist users in adjusting
a variety of monitor-related settings depending on personal preference.
Through this section, it is expected to familiarize you with the options which
are accessible via OSD menu, and to optimize your experiences with
TM/LM -7117E.
Power & OSD Buttons
Power & OSD buttons are available on the right-
hand side of the LCD monitor. Each of four OSD
controls works differently in various occasions.
Please refer to the below figure to get an idea of
how they could possibly function in relation to
OSD menu.

10
Icon
Description
OSD button
While OSD menu is activated:
to select the specific menu option
While OSD menu is deactivated:
to activate the OSD menu
EXT button
While OSD menu is activated:
to exit from the current configuration
“＋” Button
While OSD menu is activated:
to navigate through OSD menu options
to increase the value of the specific item
“－” Button
While OSD menu is activated:
to navigate through OSD menu options
to decrease the value of the specific item
While OSD menu is deactivated:
to initiate auto-adjustment function
Power Button
turn on/off the monitor
To help you get started with the OSD menu, the following points are
guidelines you are suggested to go through:
1. Firstly, press the OSD button to access the OSD menu.
2. Scroll through OSD menu options using either the “＋” or “－” button.
3. Press the OSD button to select the particular menu option of interest. It
will lead you to its sub-menu page if the selected menu option contains
sub-menu items.
4. Under the selected menu item with available sub-menu items, use the
“＋” or “－”button to switch among different items. Then, press the
OSD button to select the sub-menu item which you intend to adjust.
5. Use the “＋” or “－” button to adjust the value of the selected OSD item.
Then, press the OSD button to save settings.
6. Press the EXT button to exit from the current configuration.

11
OSD Options
Please refer to the following table for further explanation of the accessible
items.
OSD Menu Options
Sub-menu items & Description
Picture
Backlight
Press the “＋”button to increase backlight
intensity;
Press the “－”button to decrease backlight
intensity.
Brightness
Press the “＋”button to increase brightness;
Press the “－”button to decrease brightness.
Contrast
Press the “＋”button to increase contrast;
Press the “－”button to decrease contrast.
Sharpness
Press the “＋”button to increase sharpness;
Press the “－”button to decrease sharpness.
Display
Auto Adjustment
Execute the auto-tune function for OSD menu,
which will automatically perform fine tune of
the image quality for optimizing screen
performance.
H Position
Press the “＋”button to move the screen to the
right;
Press the “－”button to move the screen to the
left.
V Position
Press the “＋”button to move the screen up;
Press the “－”button to move the screen down.
Pixel Clock
Use the “＋” or “－”button to adjust the
Clock setting for VGA input.
Phase
Use the “＋”or “－”button to adjust the
Phase setting for VGA input.

12
OSD Menu Options
Sub-menu items & Description
Other
Reset
Restore the current menu back to the default
setting.
Menu Time
Specify the length of time for OSD menu to
stay active on the screen.
Language
Specify the language used in the OSD menu.
Information
Display information regarding display resolution,
horizontal/vertical sync frequency, pixel clock
(PCLK), etc.
Specifications
TM-7117E
LM-7117E
Display
LCD Panel
17" TFT LCD
Resolution
1280 (H) x 1024 (V)
Active Area
377.920 (H) x 270.336 (V)
Pixel Pitch
0.264(H) x 0.264 (V)
Pixel Arrangement
RGB Vertical Stripe
Viewing Angle
80/80/80/80 degree (U/D/L/R)
Contrast Ratio
500 : 1
Response Time
6 ms (Raising) / 2 ms (Falling)
Brightness
300 cd/m2
Touch
Touch type
5-wire Resistive or IR
N/A
Interface
USB
N/A
General Specification
Display Interface
VGA
Power Supply
12V / 40W
Dimension
401 x 385 x 286 (W x D x H in mm)
Weight
6.82 (N.W. in kg)
※ The product information and specifications are subject to change without
prior notice. To get the detailed information on TM/LM-7117E, please check
this model from Posiflex Global Website
(http://www.posiflex.com/en-global/Download/download).