PotteryBarn CHLOE BED User manual

Page 1/ 4
CHLOE BED
ASSEMBLY INSTRUCTIONS
Date: 2014-Jan-10
Rev: www.potterybarn.com

Page 2/ 4
Important Safety Instructions:
Please read all instructions carefully before assembling this bed.
For your safety, assembly by two or more adults is strongly recommended.
Keep these instructions for future use.
Use only vendor-supplied hardware to assemble this item. Using unauthorized hardware could jeopardize the
structural integrity of the item.
Pre-assembly:
Remove all parts and hardware from the box. Place all items on a carpeted or scratch-free work surface, as this
will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
To avoid accidentally discarding small parts or hardware, do not dispose of any packaging or contents of the
shipping carton until assembly is complete.
Use the parts and hardware lists below to identify and separate each of the pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
The use of power tools to aid in assembly is not recommended. Power tools can damage the hardware and split
the wood.
Parts Included:
(A) Headboard –1x
(B) Footboard –1x
(C1) Side Rail –1x
(C2) Side Rail –1x
(D) Slat –5x
(E) Support Leg –5x
Hardware Included:
(F) Threaded Bolt
(5/16" x 89mm) - 8x
(G) Flat Washer
(5/16"(∅16) ) - 8x
(H) Lock Washer
(5/16"(∅12) ) - 8x
(I) Wood Screw
(#8 x 25mm) - 10x
(J) Hex Nut
(5/16"*12mm) - 8x
(K) Half Moon
Washer - 8x
(L) Allen Wrench
(5/16") - 1x
Hardware Enclosed:
Tools Required (not included):
Philips Head Screwdriver

Page 3/ 4
Assembly Instruction Steps:
1. Attach Headboard (A) to Side Rail (C1) by aligning the pre-drilled holes on the Headboard (A) with the wooden
dowels of Side Rail (C1).
2. Secure using a Half Moon Washer (K), Flat Washer (G), Lock Washer (H), and a Hex Nut (J), as seen in the
ilustraton below.
3. Tighten with the supplied Allen Wrench (L).
4. Follow steps 1 and 2 to complete the other Side Rail (C2).
5. Attach Footboard (B) to the ends of the Side Rails (C1, C2) by aligning the pre-drilled holes of the Footboard (B)
with the wooden dowels on the Side Rails (C1, C2).
6. Secure using 4 sets of: Half Moon Washer (K), Flat Washer (G), Lock Washer (H), and Hex Nut (J), as seen in
the illustration below.
7. Tighten the hardware with the supplied Allen Wrench (L).

Page 4/ 4
8. Attach a Support Leg (E) to each Slat (D). Rotate the Support Leg (E) clockwise to tighten, as seen in the
illustration below.
Note: Do not over tighten
9. Place the 5 assembled Slats (D+E) onto the notches found on Siderails (C1 & C2), as seen in the illustrstion
below.
10. Secure the Slats with 10 Wood Screws (I) using a Philips Head Screwdriver.
Note: Do not over tighten
11. If needed, adjust the levelers underneath the posts of the Headboard (A), Footboard (B), and Support Legs (E).
12. Assembly is complete.
Care Instructions:
Dust often using a clean, soft, dry, and lint-free cloth.
Blot spills immediately and wipe with a clean, damp cloth.
We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered finish.
Hardware may loosen over time. Periodically check to make sure all connections are tight.
Re-tighten if necessary.
Thank you for your purchase
Stores | catalog | www.potterybarn.com