PotteryBarn LORRAINE User manual

Date: May. 02. 2016
LORRAINE EXT. PEDESTAL DINING TABLE

Date: May. 02. 2016
Important Safety Instructions:
•Please read all instructions carefully before assembling.
•For your safety and convenience, assembly by two adults is strongly recommended.
•Keep instructions for future use.
•Use only hardware supplied by vendor to assemble. Using unauthorized hardware could jeopardize the
structural integrity of the item.
Pre-assembly:
•Remove all parts and hardware from the box and lay them out on a clear carpeted or scratch-free work surface,
to avoid damaging parts during assembly. The shipping box provides an ideal work surface.
•Save all packing materials until assembly is complete to avoid the accidental discarding of smaller parts or
hardware.
•Use the parts and hardware list below to identify and separate each of the pieces included.
•The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
•The use of power tools is not recommended. Power tools can damage hardware and split wood.
Parts included:
(A)Table Top
1 pc
(B)Center Leaf 1 pc
(C) Pre-assembled Post and Base 1 pc
(D) Base 1 pcs
(A) (B) (C)
(D)

Date: May. 02. 2016
Hardware Included:
(E)
Bolts
Ø8mm x L45mm
(F)
Spring Washers
Ø8mm x 12mm
(G)
Flat Washers
Ø8mm x 22mm
8pcs 8pcs 8pcs
Tool Required:
(H) – Allen Key (included)
(1pc)
Assembly Instruction Steps:
1. Carefully put Pre-assembled Post and Base upside down on a carpeted or scratch-free surface. Attach Base (D)
to Pre-assembled Post and Base (C) by using 4 Bolts (E), 4 Spring Washers (F) and 4 Flat Washers (G). Tighten
with Allen Key (H) (See Fig.1). Then, lift and turn assembled pedestal on its upright position.
Fig. 1

Date: May. 02. 2016
2. Carefully put Table Top (A) upside down on a carpeted or scratch-free surface. Unlock the swivels located on
both sides of Table Top's underneath (A). (See Fig.2).
3. Grip each side of Table Top (A) and pull to open. Lift opened Table Top (A) and turn it on its upright position.
Then, place it on assembled pedestal and attach it by using 4 Bolts (E), 4 Spring Washers (F) and 4 Flat
Washers (G). Tighten with Allen Key (H) (See Fig.3).
Fig. 3
Fig. 2

Date: May. 02. 2016
4. Push back each side of Table Top.
5. Lock the swivels located on both sides of Table Top's underneath
6. Assembly is complete.
Insert/Remove the Leaf:
1. Unlock the swivels located on both sides of Table Top's underneath
2. Grip each side of Table Top and pull to open at maximum position (See Fig.4). Unpack the leaf (B) and insert it
into position, making sure to match the leaf’ s pegs with the corresponding holes.
3. Slide Table Top back to its original position until leaf is securely in place.
4. Turn the swivels to lock.
Fig. 4
Locked
Unlocked

Date: May. 02. 2016
Adjusting Levelers:
Due to an uneven floor the Table may not sit level causing it to wobble. If the Table wobbles, determine which corner
does not touch the ground correctly. With two people follow these steps:
1. Carefully lift the Table slightly to provide access to the levelers attached to the bottom of the Base.
2. Turn the levelers until adequate contact is made with the floor. Gently set down the Table and check
stability.
3. Repeat steps until Table sits firmly on the ground.
Leaf Storage:
• When not in use, Leaf should be stored in a flat position inside its bag. Avoid resting or leaning upright when
stored, to prevent misalignment of the leaf apron.
Care Instructions:
• Dust with a clean, soft damp cloth and wipe dry immediately.
• Avoid the use of chemicals and harsh cleaning agents.
Thank you for your purchase.
stores | catalog | www.potterybarn.com
Adjustable Leveler