PowerWalker BPH A72T-6 Administrator Guide

PowerWalker
How to assemble a
BPH A72T-6

Important Safety Warnings
Please comply with all warnings and operating instructions in this instruction strictly.
Read carefully the following instructions before installing the unit. Do not operate this
unit before reading through all safety information and operating instructions carefully.
• Do not try to assemble or repair the unit yourself, contact your local supplier, seek
for a qualified technician for professional assistance.
• To eliminate any overheating of the battery box, keep all ventilation openings free
from obstruction and do not place any foreign objects on top of the battery bank. Keep
the battery box 20 cm away from the wall.
• Make sure the battery box is installed within the proper environment as specified. (0-
40°C and 30-90% non-condensing humidity)
• Do not install the battery box under direct sunlight. Your warranty will be void if the
batteries fail due to overheating.
• This battery box is not designed for use in dusty, corrosive and salty environment.
• The warranty for this battery bank will be void if water or other liquid is spilled or
poured directly onto the battery box. Similarly we do not warrant any damage to the
battery box if foreign objects are deliberately or accidentally inserted into the battery
box enclosure.
• The battery will discharge naturally if the system is unused for a period of time.
• It should be recharged every 2-3 months if unused. If this is not done, then the
warranty will be null and void. During normal operation, the batteries will be
automatically remained in charged condition.
• Servicing of batteries should be performed or supervised by trained personnel with
knowledge of batteries and the required precautions.
• When replacing batteries, it is necessary to replace ALL batteries with the same
quantity, type & capacity.
• CAUTION – Do not dispose of battery or batteries in a fire. The battery may explode.
• CAUTION – Do not open or mutilate the batteries. The electrolyte from the batteries
is toxic and harmful to the skin and eyes.
• CAUTION – Risk of Electric Shock –Hazardous voltage may exist between battery
terminals and ground. Test before touching with bare hands.
• CAUTION – A battery can present a risk of electrical shock and high short circuit
current.

The following precaution should be observed when working on batteries:
1. Remove watches, rings, or other metal objects.
2. Use tools with insulated handles.
3. Wear rubber gloves and boots.
4. Do not lay tools or metal parts on top of batteries.
5. Disconnect charging source prior to connecting or disconnecting battery terminals.
• Do not plug or unplug the battery connector if UPS works in DC (discharging) mode.
Installation and Setup
NOTE: Before installation, please inspect the unit. Be sure that nothing inside the
package is damaged. Please keep the original package in a safe place for future use.
Storage and Maintenance
The unit contains no user-serviceable parts. If the battery service life (3~5 years at
25°C ambient temperature) has been exceeded, the batteries must be replaced. In
this case, please contact your dealer.
Be sure to deliver the depleted batteries to a recycling facility or ship it
to your dealer in the package that contained the replacement batteries.
Storage
Before storing, charge the unit 4 hours. Store the unit covered and upright in a cool,
dry location. During storage, recharge the battery in accordance with the following
table:
Storage Temperature
Recharge Frequency
Charging Duration
-25°C – 40°C
Every 3 Months
1-2 hours
40°C – 45°C
Every 2 Months
1-2 hours

SOP – How to assemble BPH A72T-6
Please follow the below wiring for the first three batteries. Please also use the in-
package insulating tubes to protect both loose ends.
Organize the batteries as shown below. Use the protective plastic to avoid sharp
edges damaging the wires. Fasten the batteries with the fixing plate.
450 mm
450 mm
380 mm
150 mm

Please follow the wiring for the other side as shown below.
Organize the batteries as shown below. Use the protective plastic to avoid sharp
edges damaging the wires. Fasten the batteries with the fixing plate.
150 mm
450 mm
280 mm