PowerWalker BPH AT24R-4 User manual

BPH AT24R-4/BPH AT48R-8/BPH AT72R-12
User's Manual
This manual contains important instructions. Please read and follow all instructions carefully during installation and operation of the unit.
Read this manual thoroughly before attempting to unpack, install, or operate the Battery modules.
CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area, free of conductive
contaminants. (Please see specifications for acceptable temperature and humidity range).
CAUTION! (No User Serviceable Parts): Risk of electric shock, do not remove cover No user serviceable parts inside. Refer servicing to
qualified service personnel.
CAUTION! (Non-Isolated Battery Supply): Risk of electric shock, battery circuit is not isolated from AC power source; hazardous voltage
may exist between battery
terminals and ground. Test before touching.
CAUTION! Wiring must be done by qualified personnel.
CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire, do not use with or near aquariums. Condensation from
the aquarium can come in contact with metal electrical contacts and cause the machine to short out
CAUTION! Do not dispose of batteries in fire as the battery may explode.
CAUTION! Do not open or mutilate the battery, released electrolyte is harmful to the skin and eyes.
CAUTION! A battery can present a risk of electric shock and high short circuit current. The following precaution should be observed when
working on batteries.
Remove watches, rings or other metal objects.
Use tools with insulated handles
CAUTION!
CAUTION! Connect the Protection Earth (PE) safety conductor before any other cables are connected.
DO NOT INSTALL THE UNIT WHERE IT WOULD BE EXPOSED TO DIRECT SUNLIGHT OR NEAR A STRONG HEAT SOURCE!
SERVICING OF BATTERIES SHOULD BE PERFORMED OR SUPERVISED BY PERSONNEL KNOWLEDGE OF BATTERIES AND THE
REQUIRED PRECAUTIONS. KEEP UNAUTHORIZED PERSONNEL AWAY FROM BATTERIES!
HARDWARE INSTALLATION
These batteries modules can be mounted in a rackmount or vertical tower orientation. This versatility is especially important to growing
organizations with changing needs that value having the option to position a batteries module on a floor or in a rackmount system. Please
follow the instructions below for the respective mounting methods.
SAFETY PRECAUTIONS
CAUTION! To prevent the risk of fire or electric shock, only use the supplied hardware to attach the mounting brackets.
1.0n-board Replaceable Fuse Cover
Replaceable fuse is accessible from the rear panel. It must be done
by qualified personnel.
2. Battery Output Connector
Use this output Connector to connect the Battery module to the
Power module or to the next Battery module.
3. Input Connector
Use this input connector to daisy chain the next Battery module.
Remove the connector cover for access.
IMPORTANT SAFETY INSTRUCTIONS
UNPACKING
The box should contain the following:
Batteries Module
User's manual
Battery Cable
Rackmount ears (2 PCS)
Flat head screws: M4X8L (8)
Pan head screws: M5X12L (4)
Screw hole dust covers (8)
Ground wire
BASIC OPERATION
FRONT/REAR PANEL DESCRIPTION
EBM 24V/48V/72V
Step 2 Rackmount rails installation
1) The rails adjust to mount in 48-cm (19-inch) panel racks from
52 to 91.5cm (20.5 to36 inches) deep. Select the proper holes in
the rack for positioning the batteries module in the rack. It takes
up position 1 through position 6 Step 3: Install the batteries module on the rack
Place the batteries module on a flat stable surface with the front of
the unit facing toward you. Secure the batteries module to your rack
with four M5X12L screws at the front of the rack. (Located in
position 2 & position 5).
2) Attach the rackmount rail to your rack with two M5X12L screws
and two plastic washers at the front of the rack. (Located in position
1 & position 6) Do not tighten the screws. Adjust the rail size on the
rail assembly of your rack. Secure the rail to the rear of the rack with
two M5X12L screws and two plastic washers. Tighten all screws at
the front and rear of the rail. Once completed, perform the same
steps for assembling the other rackmount trail.
RACKMOUNT INSTALLATION
Step 1: Rackmount ears installation
Attach the two rackmount ears to the batteries module using
the provided screws M4X8L*8pcs
position 1
position 5
position 1
position 3
position 2
position 5
1 2 3
1 2

TECHNICAL SPECIFICATIONS
Step 2: Attach dust covers
Insert dust cover into the rackmount ear screw holes that are
not being used.
CONNECTION #1 : POWER MODULE(UPS) WITH ONE
BATTERIES MODULE
Rotate the battery cable retention bracket and tighten the two
screws to fix battery cable on the Power module and Batteries
module.
CONNECTION #2 : POWER MODULE(UPS) WITH MULTIPLE
BATTERY MODULES
Step 1: Use the battery cable to connect the 2nd Batteries module
to the 1st Batteries module.
Step 2: Rotate the battery cable retention bracket and tighten the
two screws to fix battery cable on 1st batteries module and 2nd
Batteries module.
VERTICAUTOWER INSTALLATION
Step 1: Attach the base stands
Tighten the screws (M5X12*8pcs) of the base stands (rackmount
ears) onto the bottom of the batteries module.
KO1-C000785-00
Battery Installation and replacement
Step1 : unscrew and remove the top cover from the battery module
Step2: unscrew and unplug steel straps from the battery module
Step3: remove the battery pack from the module
Step4: open the battery pack and replace the batteries
Model BPH AT24R-4 BPH AT48R-8 BPH AT72R-12
Battery
Sealed Maintenance Free 12V / 9Ah x2pcs 12V / 9Ah x4pcs 12V / 9Ah x6pcs
Lead Acid Battery x2sets x2sets x2sets
Rated Battery Voltage 24Vdc 48Vdc 72Vdc
Overload Protection Fuse
Physical
Dimensions (HxWxD) 88x438x430 mm 88x438x610 mm
Weight (kg) 15.10 24.60 36.02
Environment
Operating Temperature 0°c to 40°C
Relative Humidity 0 to 90% (Non-condensing)
Step5: the accumulating block b lower cover.set the steel straps and
the top cover again.
34
For more information, visit www.powerwalker.com
All rights reserved. Reproduction without permission is prohibited.