Precor C954 User manual

•
•
PRECOR~
Commercial Treadmill Owner's Manual
C9S4
C9S&
COMMERCIAL PRODUCTS DIVISION

IMPORTANT SAFETY INSTRUCTIONS
DAN GER _ To reduce the risk of electrical shock,always unplug the unitfrom its
powersource before cleaning or performing any maintenance tasks.
WARNING _To reduce the risk of burns, fire, electric shock, or injury to
persons, take the following precautions:
When using the C956 or C954 treadmill, always follow basic precautions, including the following:
• To ensure your safety and to protect the unit, read all the instructions before assem-
bling and using the treadmill.
•
To ensure the proper use and safety of the treadmill, make sure that all users read
this manual. Please make this manual a part of your club's training program.
Remind the club users that before beginning any fitness program, they should
obtain complete physical examinations from their physicians.
1/ est conseille de subir un examen medical complet avant d'entre-prendre tout
programme d'exercise. Si vous avez des etourdissements ou des faiblesses, arretez
les exercices immediatement.
DIVISION PRO D U C T S
COMMERCIAL
•Do not allow children or those unfamiliar with its operation on or near the treadmill.
Do
not leave children unsupervised around the treadmill.
•Never leave
the treadmill unattended. Unplug the unit from the power outlet when it
is not in use, before cleaning it, and before putting on or taking off parts. Do not
adjust the running belt when someone is standing on the unit.
•
Assemble and operate the treadmill on a solid, level surface. Locate the treadmill a
few feet from walls or furniture. Check the unit before each use and verify that all
fasteners are secure. Maintain
the treadmill in good working condition.
•Use the treadmill only for its intended use as described in this manual. Do not use
accessory attachments that are not recommended by the manufacturer; such attach-
ments might cause injuries.
•If you purchased the optional POLARe chest strap, review the guidelines found in
the Pre cor Heart Rate Option Owner's Manualthat is supplied with that option.
•Never operate the unit if it is damaged, if it is not working properly, if it has been
dropped, or if it has been dropped in water. Return the unit to a service center for
examination and repair.
•Keep all
electrical components such as the motor, power cord, and VO switch, away
from liquids to prevent shock. Do not set anything on the handrail, display console,
or hood. Place liquids, magazines and books in the appropriate receptacles.
•Keep
the power cord away from heated surfaces.
•Do
not operate the treadmill where aerosol (spray) products are being used or where
oxygen is being administered.
•Do not use outdoors.
•The security clip must be attached at waist level prior to beginning a workout. A cord
connects the security clip to the red STOP button on the console. If a user encoun-
ters difficulties, a strong tug on the security cord or a quick tap on the red STOP
button will stop the running belt.
•Use care
when getting on or off the treadmill. Use the stationary handrail whenever
possible. Place your feet firmly on the right and left side platforms before the run-
ning belt begins moving (prior to a workout). Step onto the running belt when the
speed is at or below 1 mph (1.6 kph).
-
•page 2

--- --- -----------------
SAFETY APPROVAL
GROUNDING INSTRUCTIONS
DIVISION
240-volt grounding plug
PRO D U C T S COMMERCIAL
120-volt grounding plug
When identified with the ETL -e logo, the treadmill has been tested and conforms to the require-
ments of CAN/CSA-E-335-1/3-94, Safety of Household and Similar Electrical Appliances.
IMPORTANT SAFETY INSTRUCTIONS
The C956 or C954 treadmill must be grounded. If it should malfunction or break down, grounding
provides apath of least resistance for electric current which reduces the risk of electrical shock.
The C956
or C954 treadmill is equipped with apower cord having an equipment-grounding
conductor and agrounding plug. The plug must be inserted into an appropriate outlet that is
properly installed and grounded
in accordance with all local codes and ordinances. If you do not
follow these Grounding Instructions, you could void the Precor limited warranty.
DA NGER - Improper connection of the equipment-grounding conductor can
result in arisk
of electric shock. Check with aqualified electrician
or service person if you are in doubt as to whether the treadmill is properly grounded. Do
not modify the plug provided with the treadmill. If it doesn't fit the outlet, get aproper outlet
installed
by aqualified technician.
Diagram 1
Correct power
outlet for U.S. 'r
Markets:
120-volt and
240-volt plugs.
•Never step off the treadmill while the running belt is moving. Keep your body and
head
facing forward. Never attempt to turn around on the treadmill.
•Never turn ON the treadmill when someone is standing on the machine.
•Never
block the air openings on the hood while operating the treadmill. Keep the air
openings clean and free of lint, hair, or anything that might impeded the free flow of
air. Never drop or insert objects into any opening.
•Wear proper exercise clothing and shoes during a workout-no loose clothing. Tie
long hair back. Keep all loose towels away from the running surface. The running
belt will not stop immediately if an object becomes caught in the belt or rollers.
•Do
not rock the unit. Do not stand on the display console or hood.
•Do not overexert yourself or work to exhaustion. If you feel any pain or abnormal
symptoms, stop your workout immediately and consult your physician.
120V Units and 240V Units Designated for U.S. Markets
The C956 or C954 treadmill must be connected to adedicated, grounded circuit. A20 amp
dedicated circuit is recommended. The treadmill is factory-equipped with aspecific power supply
cord to permit connection to aproper electric circuit as shown
in Diagram 1. Make sure that the
treadmill is connected to an outlet having the same configurations as the plug. No adapter should
be used with this product.
•
SAVE THESE INSTRUCTIONS page 3

------------------------ ---
COMMERCIAL
Table of Contents
PRO D U C T S
DIVISION
Important Safety Instructions 2
Safety Approval 3
Grounding Instructions 3
Radio Frequency Interference (RFI) 6
European Applications 6
Obtaining Service................................................................... 7
About this Manual....... 7
Unpacking theTreadmill 8
Standard Equipment............................................................... 8
Other Equipment................ 8
Hardware Kit 9
Setting Up theTreadmill 10
Installation Requirements 10
Additional Tools Needed 10
Assembly Instructions 10
Turning the Unit ON and OFF 18
Checking the Alignment of the Running BelL 19
Club Information 20
Changing the Club Settings 20
Selecting the Language 21
Determining the Units of Measure 21
Determining the Club Speed Limit 22
Setting aWorkoutTime Limit.. 22
Setting aPause Time Limit 22
Changing the C956 Custom Courses 23
Viewing the Odometer, Hours of Use,
Software Version, and Error Log 24
Using CSAFE Standard Equipment 24
page 4

--_._------- ------------------
COMMERCIAL
Table of Contents
PRO D U C T S
DIVISION
The C956/C954 Display 25
Features on the Display Console 25
Top Display Windows 26
Upper Display (C956 only) 26
Center Display (C956 and C954) 26
Keys on the Display Console 28
Keypad Tips 28
Exercising on theTreadmill 32
Using the Security Clip 32
Pause, Workout Summary and Exit Features 32
Quick Steps to Working Out 34
Workout Tips 34
Cooling Down After a Workout 35
Courses 36
The Heart Rate Features 36
Using the Smart Rate~Feature 36
Manual Mode and the Quick Start Key 37
C956 Track Course 38
C956 Preprogrammed Courses 38
C956 Interval Course 38
C956 Custom Courses 39
C956 Random Course 39
C956 Heart Rate Course 40
C956 Weight Loss Course 41
C956 Goal-based Courses 41
Maintenance 42
Cleaning the Equipment 42
Aligning the Running Belt 41
Storing the POLAR~ Chest Strap 44
Servicing the Treadmill 44
Long Term Storage 44
C934 Exploded Views 45
Specifications back cover
pageS

COMMERCIAL
PRO D U C T S
DIVISION
RADIO FREQUENCY INTERFERENCE (RFI)
Federal Communications Commission Part 15
The treadmill has been tested and found to comply with:
•The IEC EMC Directive (international electromagnetic compatibility certification)
•
The limits for aClass Adigital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in acommercial installation.
The treadmill generates, uses, and
can radiate radio frequency energy and, if not installed and used in accor-
dance with the owner's manual instructions, may
cause harmful interference
to radio communications. Operation of the treadmill in aresidential area is
likely
to cause harmful interference. If this occurs, the user will be required to
correct the interference at his or
her own expense.
CAUTION -Per FCC rules, changes
or modifications to the
treadmill
not expressly approved by Precor, could
void the user's authority to operate the equipment.
Canadian Department of Communications
This digital apparatus does not exceed the Class Alimits for radio noise emissions
from digital apparatus set
out in the Radio Interference Regulations of the Canadian
Department of Communications.
Le present appareil numerique n'emet pas de bruits radioeelectriques oopassant les
Ii mites applicables aux appareils numeriques de la Class Aprescrites dans Ie
Reglement sur
Ie brouillage radioelectrique edicte par Ie ministere des Communica-
tions du Canada.
EUROPEAN APPLICATIONS
This product conforms to the requirements of the European Council Directive 89/336/
EEC, Electromagnetic Compatibilityand has been tested to the following standards:
EN55022, Limits &Methods of Measurement of Radio Interference, Information Tech-
nology Equipment (Class A). Per the standard, the treadmill is aClass Aproduct. In
adomestic environment, this product
may cause radio interference, in which case
the user is responsible to take adequate measures to alleviate the interference.
EN50082-1,
Generic Immunity Standard for Residential, Commercial and Light
Industrial Products (Class A).
This product additionally conforms to the requirements of the European Council Directive
731231EEC, Low Voltage Directive and has been tested to the following standard:
IEC 335-1, Safety of Household and similar Electrical Appliances.
page 6

COMMERCIAL
OBTAINING SERVICE
PRO D U C T S
DIVISION
Do not attempt to service the treadmill yourself except for the maintenance tasks
described
in this manual. The treadmill does not contain any user-serviceable parts.
For information about product operation or service, visit the Precor
Web Site at
www.precor.com or contact an authorized Precor Commercial Products Customer
Service Representative at 1-888-665-4404.
To help customer service personnel expedite your call, have your serial number
available. The serial number can be found on the shipping container or on the label
near the power receptacle. If you have any questions regarding the treadmill, use
the model and serial numbers whenever you call aPrecor dealer or Commercial
Products Customer Service Representative.
Model number: C956
or C954
Unit number:
Unit number:
Unit number:
ABOUT THIS MANUAL
Serial number: _
Serial number: _
Serial number: _
This manual includes instructions for installing and using the treadmill.
To maximize
the use of the treadmill, please study this manual thoroughly. The manual uses the
following conventions for identifying special information:
Note: Contains additional information.
Important: Indicates information to which you should pay specialattention.
CAUTION: Indicatessteps or information necessaryto preventharm to your-
self or damageto the equipment.
WARNING: Provides instructionsto preventelectrical
damage tothe equip-
ment and injuries to yourself.
DANGER: Indicates steps you musttake to preventelectrical shock.
page?

COMMERCIAL
PRO D U C T S
DIVISION
oHardware kit
oOwner's Manual
oPowercord
Unpacking the Treadmill
Thank you for purchasing the Precor C956 or C954 treadmill. Built to the exacting
standards of the health club environment, the treadmill is intended for commercial
use and can withstand the rigors of daily club use with little maintenance.
Important: Before using the treadmill, we urge you to familiarize yourself and
yourstaffwith the entire Owner's Manual. Understanding this manual willhelpyou
and yourcustomers use the treadmill safely and successfully.
CAUTION:This unit weighs over 350 pounds (158 kilograms).To prevent injury
to yourself or damage to the equipment, obtain appropriate assistance before
removing the unit from the pallet.
The treadmill is carefully inspected before shipment so it should arrive
in good
operating condition. Precor ships the unit
in the following pieces:
Base frame assembly with hood
Two upright supports
oDisplay console with cable
:J Two handrails (left and right)
If any items are missing, refer to Obtaining Service on page 7.
STANDARD EQUIPMENT
The treadmill incorporates the Precor Smart RateiP> and Heart Rate features into its
display console. Devices, such as FitLinxxlP>, that are CSAFE compatible, can also
be attached.
The Precor "touch" heart rate is standard on the C956 and provides electrode
strips, called "grips," on the center handrail. When auser grasps the metal-portion
of the center handrail, aheart rate
is transmitted to the receiver.
Note: If auser does not wish to use the touch-sensitive hand grips, an optional
POLAR(!lchest strap can be purchased and worn. The chest strap transmits the
user's heart rate and it appears as anumber
in the HEART RATE display.
Important: The Precor "touch"heartrate is notavailable on the C954 treadmill,
but the SmartRatfP
and heartrate features will appearon the display if the user
wears the optional
POLA~chest strap.
OTHER EQUIPMENT
Optional equipment available through your dealer includes:
• POLARiP> chest strap.
•Long handrails.
If you are interested
in obtaining Precor option kits for your unit, check with your
dealer. For customer service, see ObtainingServiceon page 7.
page 8

COMMERCIAL
HARDWARE KIT
PRO D U C T S DIVISION
Diagram 2
After unpacking the treadmill, open the hardware kit and make sure that you have
the following items shown in Diagram 2.
o(A) twelve 1-inch buttonhead hex screws
o(B) twelve flat stainless steel washers -place on 1-inch buttonhead hex screws
(C) four 1/2-inch flat head hex screws -attach to
upper handrails
(D) four 31/4-inch socket head screws -install upright supports
(E) four flat black washers -place on 31/4-inch socket head screws
o(F) four barrel spacers -place on 3 1/4-inch socket head screws after washers
(G) 5/32-inch hex key -attach handrails to display frame
o(H) 3/16-inch hex key -attach hood, mount upright supports, attach display
and handrails to base frame
o(J) 1/4-inch hex key -attach upright supports to base mounting brackets
o(K) 5/16-inch hex key -adjust running belt
Hardware kit (not shown to scale).
A
o
F
G
H
J
K
Note: After assembling the treadmill, be sure to store the hex keys in asecure
place. The tools are used for specific maintenance procedures that are described
in this manual.
page 9

COMMERCIAL
PRO D U C T S
DIVISION
Setting Up the Treadmill
You do not need any special knowledge or experience to set up the treadmill.
However, because of its size and weight, you will need to obtain assistance.
INSTALLATION REQUIREMENTS
Follow these installation requirements when installing the treadmill. If you do not
install the treadmillaccording to the followingguidelines, you could voidthe Precor
limitedwarranty.
•Set up the treadmill on asolid, flat surface. Unpack and assemble the treadmill
close to where you plan to use
it. Make sure that the flat surface under the unit is
smooth and
level. A level unit is required for the user's safety and proper operation.
•
Provide ample space around the unit. Open space around the unit makes
for asafer mount and dismount.
•Fill
out and mail the limited warranty card. The serial number can be found
on the shipping container or on the label near the power receptacle. Write the
serial number onto the Precor limited warranty card found
on the back cover of
this manual and
in the Obtaining Service section on page 7.
•Use the appropriate voltage, dedicated circuit, and grounding as speci-
fied on the treadmill. The treadmill is available in both 120-volt and 240-volt
models. Refer to the treadmill's identification label to determine the voltage
that your treadmill requires. Both the 120-volt and 240-volt models require a
dedicated circuit. A 20 amp circuit is recommended.
CAUTION:
Do not use a non-grounded outlet or transformer. Do not
remove or otherwise bypass the plug with an adapter. Electrical damage
can occur and void the Precor limited warranty if the treadmill is
connected to an improper power source. Refer to Grounding Instructions
on page 2.
ADDITIONAL TOOLS NEEDED
Obtain the following tools beforeassembling the treadmill.
Wire cutter 0Medium weight string
::J Bubble level ::J 1/2-inch box end wrench
oSAE standard socket set with aratchet or 8-inch crescent wrench
ASSEMBLY INSTRUCTIONS
Take the following steps to assemble the treadmill.
CAUTION:To
avoid injury and ensure your safety, get assistance before
moving the treadmill off the pallet. Do not drop the unit.
1. Think about the site and location. Have your assistants help place the shipping
carton close to the location where
you plan to use the treadmill. Break down the
side walls of the shipping carton so that they lie flat. Remove the loose contents.
2. Make sure that the power switch is OFF. Check the ON/OFF power switch
on the front of the treadmill. Place the switch in the 0(OFF) position. Make
sure that the treadmill is not plugged into apower source.
page 10

COMMERCIAL PRO D U C T S
DIVISION
Diagram 3
Diagram 4
Lift the rear of the
unit
and roll it to
its assembly
location.
Rear end cap-"itt-tr--"'l:::==;;;;t" .....9
Lift the unit by'--f--+--""T""----r==r
grasping the
hand holds
inside the rear
end caps.
3. Move the treadmill. Diagram 3. Grasp the hand holds inside the rear end
caps and use proper lifting techniques
to lift the rear end so that you can roll
the treadmill on its front wheels. To avoid injury to yourself or damage to the
unit, ask for help in placing the treadmill where you plan to use it.
Remove the
hood.
Front screw --~-\---:
Hood----+_
Side screw --+--------:l\o-----
4. Removethe hood. Diagram 4. Loosen and remove the four buttonhead screws
using the 3116-inch hex key. Inset #1 shows the location of one of the front
screws. Inset #2 illustrates the location
of the side screw. The other is on the
opposite side. Lift the hood off the treadmill and set it aside.
page 11

-------------------------------------
COMMERCIAL
PRO D U C T S
DIVISION
Diagram 5
Diagram 6
page 12
Remove the
shipping
fasteners from
the left side front
panel.
Shipping
fasteners found
-+-----'''---\\---'!<-2'111.
on left and right
sides of the front
panel.
Left side
mounting
bracket
----+--_B_-+----
J
5. Attach the left side upright support. Diagram 5. Take the following steps.
a. Remove the shipping fasteners from the front panel. With the supplied hex
key and a
Y2-inch box end wrench, loosen and remove the two bolts, washers
and nuts on the left side of the front panel. These fasteners hold the front
panel in place during shipping. (The front panel will drop slightly when you
remove the fasteners.) Discard the nuts, but keep the bolts and washers.
Secure the left II
upright support.
Screws (D),
--I--------f----+--+
washers (E),
and barrel
spacers (F)
Left upright
support
----+----t---r
b. Attach the left upright support by placing it inside the base mount and
aligning the mounting holes. Obtain two bolts, washers
and barrel spacers
from the Hardware kit. Place awasher and barrel sleeve on each bolt and
insert the fasteners through the side of the upright support
and into the
base mounts. Use the 1/4-inch hex key to secure the bolts, but leave room
for adjustments. See Diagram 6, #1.
c. Reinsert the two shipping fasteners (bolts
and washers only) removed in
step 5a, and finger tighten.
See Diagram 6, #2.

COMMERCIAL PRO D U C T S
DIVISION
Diagram 7
Diagram 8
Attach the
display console
to the left upright
support.
Display console -+-----_+_
Display cable--r--.~~~------,,~
Screws (A) with
washers (8) ---t-----fr----,j1-f-----f------::="OO
Left side
upright support
-t==£=-_----lu. .!::::~~==~===::::!1
CAUTION: To avoid damageto the display cable, read the following steps
carefully. Damageto the cable dueto improperassembly is not covered
by the Precor limited warranty.
6. Secure the display console to the left uprightsupport. Diagram 7. Remove
any tape or wire ties that secure the display cable. Unwrap the cable to remove
kinks. Ask
an assistant to hold the display console in place while you attach it to
the left upright support using two buttonhead screws (A) with washer (B).
Finger tighten.
Remove right
side front panel
screws.
Right side -- ~
mounting bracket
Front panel--i-''t----~~ __ ---- .. .:
fasteners
7. Prepare to attach the right side upright. Diagram 8. Take the following steps:
a. Remove the shipping fasteners from the right front panel. Follow the same
process as in step 5a. With the supplied hex key and a
Y2-inch box end
wrench, loosen and remove the two bolts, washers and nuts on the right side
of the front panel.
page 13

COMMERCIAL
PRO D U C T S
DIVISION
Diagram 9Route the cable. D
Right upright
support
Display cable
Base frame
Base mounting
bracket
Right upright
support
Bracket hole
Lower board
b. Route the display cable through the right upright support. Ask an assistant to
hold the upright support close to the right side mounting bracket. Route the
cable through the upright support (see Diagram 9. #1) and pull it out of the
large hole
on the side of the support near its base. Diagram 9. #2.
Note: If you encounter difficulties with the cable. try tying astring to the
end of the cable. Attach a
washer to the opposite end for weight and route
it through
the upright support.
c. Ask your assistant to position the right upright support inside the base
mounting bracket and align the mounting
holes as you pull the cable through
the mounting bracket hole in the base frame. See Diagram 9. #3.
Diagram 10
page 14
Connect the
cable.
Cable
connector+------------t:x-·~
Lower board --+---=-~-:
Display cable-+-----I--
d. Plug the cable connector into its receptacle on the lower board near the
motor.
See Diagram 10. Adefinite "click" is heard when the cable is properly
attached. If you
do not hearand feel theconnector snap into place. reinsert it.

COMMERCIAL
PRO D U C T S
DIVISION
Diagram 11
Diagram 12
Secure the right
upright support.
Screws (D),
washers
(E),
and barrel
spacers (F)
--+= ~ .....
Tighten so that
the upright is
secure, but
leave room for
adjustments.
Right upright
support
---4-----,,,L----
Front panel--+-::.,.L..---------.'L-------~~
8. Secure the upright support. Diagram 11, #1. Obtain two screws (D), washers
(E) and barrel spacers (F) from the Hardware kit. Place awasher and barrel
sleeve on each bolt and insert the fasteners through the side of the upright
support and into the base mounts. Secure the upright support using the 1/4-inch
hex
key. See Diagram 11 ,#3.
Important: Do not securelytighten the screwsuntilafterthe unithasbeenfully
assembled. Make sure thatthe bolt
and spacerdo not pinch the cable.
9. Insert the two bolts removed in step 5a, and finger tighten. Diagram 11, #2.
Secure the
display console.
Display
console4---
1-inch screws (A)
with washers (8)
Tighten the
screws, but
----1I-1----~ ......... f___:111\
leave room for
adjustments.
10. Secure the display console to the upright supports. Diagram 12. Align the
display console with the right side upright support mounts. Insert two 1-inch
screws (A) with washers
(8) and finger tighten. Fully tighten the screws using
the hex key provided. Do the same for the opposite upright support. See inset
in Diagram 12.
page 15

COMMERCIAL PRO D U C T S
DIVISION
Diagram 13 Handrailalignment and installation.
Handrail-+-+---'-<:T--T/
45° angle -ffi-+-Ir------:!I.
Screw (A)
and
washer (C
Lower
handrail
bracket
-+h"L-7"4c~'-P--bJ=:J'---'1
Important: With the handrails attached, the width of the treadmill is 33M!
inches (85 cm). It will not fit through astandard32-inch doorway.
11. Attach the handrails. Diagram 13. For ease of assembly, place the side rails
or adjustable rear feet on blocks. Obtain assistance to lift the treadmill.
Do
not place blocks beneath the running bed.
To attach the handrails, perform the following steps on one side at atime:
a. Alignment pins on the top of the handrails necessitate sliding the handrails
into the console assembly at a 45° angle. Position the handrail as shown in
Diagram 13, #1 and #2 and slide it onto the console extension. When the
alignment pins are fully engaged, carefully lower the handrail toward the
base. Insert two flat head screws (C) into the upper handrail mounts and
finger-tighten. See Diagram 13, #3.
b. Align the lower handrail bracket with the two base mounts and insert two
screws (A) with washers (B). See Diagram 13, #4. Tighten the screws with
the hex
key. See Diagram 13, #5.
c. Return to the upper handrail screws and securely tighten each one.
d. Perform steps a. through c. on the opposite side.
e. Obtain assistance and remove the blocks from beneath the base.
page 16

---------------------------
COMMERCIAL
PRO D U C T S
DIVISION
Diagram 14
Diagram 15
Secure the
fasteners and
replace the
hood.
Altemately---++----i"
tighten four
side upright
screws.
Alternately
tighten the four
front panel
screws.
---<.
Alternately tighte
the four screws
that secure the
-11------':::....---------"
display console.
12. Replace the hood. Diagram 14. Reposition the hood on the treadmill and replace
the four buttonhead screws removed in step 4. The two screws with washers are
placed through
the front panel. Tighten the screws using the 3116-inch hex key.
13. Tighten all mounting screws with the hex keys provided. Diagram 14.
Start at the front of the treadmill with the four screws that attach the upright
supports to the front panel. Tightening these screws first helps pull the rest of
the treadmill's parts into alignment. Then, proceed with tightening the four screws
(D) that secure the upright supports, the four console assembly screws (A), the
handrail assembly screws (A) and (C), and the hood screws.
Adjust the level
of the treadmill.
Bubble level---+-,.
Running belt --+~
Adjustable rear
foot -----+-::
14. Level the unit. Diagram 15. The C956 or C954 has adjustable rear feet. Check
to make sure that the running surface is level (use abubble level as shown in
Diagram 15).lf the treadmill is placed on aslightly, uneven surface, adjusting
the rear feet can help, but will not compensate for extremely uneven surfaces.
Important: If you need to make adjustments, adjust one rear foot at atime.
Do
not use the rearfoot to raise or lower the unit more than ~-inches. Check
the
level of the unit after each adjustment.
page 17

COMMERCIAL PRO D U C T S
DIVISION
Diagram 16 Raise or
lower the
deck.
Hand holds
on rear end
caps
Adjustable
rear foot
-t-f--T--\- __ ----+-+.e:::..--==-1I ~~~!I~
II
15. Adjust the rear deck. Diagram 16. To raise the rear deck, situate yourself
next to the adjustable rear foot. Ask an assistant to lift the rear of the tread-
mill slightly while you turn the adjustable rear foot clockwise. Turning the rear
foot counterclockwise lowers the unit.
CAUTION: The treadmill requires adedicated, grounded circuit. A20 amp
dedicated circuit is recommended. Make sure that no other product or
machine usesthe same circuit as the treadmill.
16. Connectthe powercord. Unwrap the power cord from the packing material
and plug it into its receptacle on the front panel. Make sure that the ONIOFF
(1/0) power switch is placed in the OFF (0) position and connect the power
plug to adedicated, grounded circuit.
TURNING THE UNIT ON AND OFF
Use the ONIOFF (1/0) power switch, located on the front panel, to turn the unit
ON and OFF.
To complete the installation of the treadmill, continue with Checking theAlignment
of the RunningBelt.
page 18

-
COMMERCIAL
PRO D U C T S
DIVISION
tracks centered on the
running surface
CHECKING THE ALIGNMENT OF THE RUNNING BELT
The belt is aligned at the factory before shipment. However, during shipment or by
using the treadmill on an uneven surface, the belt might move off center. Proper
belt alignment is important because it allows the belt to remain centered and
assures smooth operation.
Follow these steps to check the alignment:
1. The treadmill has adjustable rear feet. Check to make sure that the running
surface is level (refer to steps 14 and 15).
2. Locate the 1/0 switch at the front of the treadmill and turn the unit ON.
3. Stand beside the treadmill and press Quick Start. The running belt starts
automatically after the message,
"Belt Starting 3,2, 1, ..."appears.
4. Continue standing next to the treadmill and hold down the Speed .. key until
the display shows aspeed of 3miles per hour
(5 kph).
5. Walk around to the rear of the unit and observe the belt for a few minutes as
it moves.
If
the running belt,... Then,...
the belt is functioning correctly. It is
evenly distributed between the side rails
so no adjustment
is necessary.
runs or drifts off center you need to adjust the belt; see
Aligning the RunningBelt, page 42.
CAUTION: If you
notice that the belt needs alignment, make the adjust-
ments at once. Failure to do so might cause the belt to tear or fray
which is not covered by the Precor limited warranty.
6. To stop the running belt, press the red Stop button.
If the belt is functioning correctly, the treadmill is ready to use. Please continue
on to Club Information to learn how to customize the treadmill for your Club.
page 19

COMMERCIAL
,Club Information
PRO D U C T S
DIVISION
These next few pages provide information that lets you customize the treadmill for
your Club. It is not information that your customer needs
or, necessarily, should
see. This section covers the following information about how to:
•determine which language appears on the display
•set maximum speed, workout, and pause times
•design custom courses
•display the odometer and other useful information
•connect to CSAFE compatible devices
Note: If your customers are interested
in the leaming more about the C956 or C954
treadmill, you may wish to direct them to the manual available on Precor's web site
(www.precor.com). (The manual that appears on the web site does not contain the
information found
in this section.)
Diagram
17 Displayconsole keypad. Numerical
pad disabled while in
Club Custom mode.
Note:
The CHANGE key is not shown in this diagram.
Refer
to Diagram 18for its location.
CHANGING THE CLUB SETTINGS
Gently, press and hold
the Tor •key to view
the available selections.
The Club "custom" settings are accessed through specific codes that help elimi-
nate unauthorized access. Refer to Diagram 17 to locate the keys. Information that
you can access and features that can be customized are as follows:
•
Language -Choose to display English, German, Spanish or French.
•
Units of Measure -Select between U.S. Standard and Metric displays.
•
Maximum Speed -Determines the maximum speed that auser can select.
Selections range between 0.5 to 12 mph
(1 -20 kph).
•
Maximum Workout Time -Sets amaximum limit on workout time.
Note: Remember that the user will get
an additional 5-minute cool down period
appended to acompleted course. So, adjust the maximum time limit accordingly.
•
Maximum Pause Time -Sets the maximum duration in which aperson
can "pause" his
or her workout.
•
Custom Course 1 and 2 - Provides 2courses that can be customized for
aspecific user
or general club purpose.
•Odometer,
Hours of Use, Software Version, and Error Log -The treadmill
stores the cumulative miles or kilometers, the number of hours that the unit has
been
in use, the software version and software type (which is valuable when
calling customer service), and an error log (useful when troubleshooting).
page 20