Pretorian SimplyWorks JOYSTICK User manual

Symptom Possible Cause / Remedy
Unit not functioning
No cursor movement
LED remains lit
• Units are not paired. Following pairing procedure.
• Batteries flat in SimplyWorks® JOYSTICK.
Replace battery.
• Check USB connection to computer.
• Units may not be paired. Follow pairing procedure.
Units will not Pair - LED
is extinguished after
30 seconds.
• Batteries flat in either toy control receiver or
SimplyWorks® JOYSTICK. Replace battery.
• Ensure SimplyWorks® JOYSTICK is within 1
metre of receiver while pairing.
INSTRUCTIONS
SimplyWorks ®
Pack Contents
Carefully check the contents
of the box, which are:
JOYSTICK
SimplyWorks® is the world's first fully
integrated wireless system specifically for
users with motor skill difficulties.
SimplyWorks® allows you the freedom to
create wire-free, single or multi-user learning
environments, reducing set up time and
allowing you to concentrate on the learning
tasks themselves.
The SimplyWorks® JOYSTICK can be used with
any SimplyWorks® receivers for computer
imput, or to control toys and other battery
operated appliances.
With movement responding to the lightest
touch of the joystick, this is the only wireless
joystick specifically designed for users with
motor skill difficulties.
If your SimplyWorks® JOYSTICK does not operate correctly, please use the following guide to
determine the cause. If, after following this guide, your unit still does not operate, please contact
your supplier before returning it.
Your SimplyWorks® JOYSTICK is warranted for 24 months against defects in manufacture or
component failure. The unit is designed for domestic, educational, commercial and light
industrial applications. Use outside these areas will invalidate the warranty. Unauthorised repair
or modification, mechanical abuse, immersion in any liquid or connection to incompatible
equipment will also invalidate the warranty. Product Description
Troubleshooting
Warranty
Unit works erratically • Batteries flat in either toy control receiver or
SimplyWorks® JOYSTICK. Replace battery.
• Out of range - move receiver unit closer to
SimplyWorks® JOYSTICK.
• Interference - place receiver and
SimplyWorks® JOYSTICK away from sources
of interference.
SimplyWorks
®
JOYSTICK
T-Bar and
Soft Ball handles
This manual
SimplyWorks
®
Unit 37 Corringham Road Industrial Estate
Gainsborough Lincolnshire DN21 1QB United Kingdom
Tel [phone] Fax [phone]
www.pretorianuk.com
SimplyWorks®is a registered trademark of Pretorian Technologies Ltd.
S040019

Before you can use your SimplyWorks®
JOYSTICK it must be paired with one of the
SimplyWorks® receivers (RECEIVE, CONTROL
LITE, CONTROL, CONTROL PRO). To pair the
units use the following procedure:
1 Remove the battery cover on the
SimplyWorks® JOYSTICK.
2 Place the receiver within 1 metre of your
SimplyWorks® JOYSTICK.
3 Briefly press the Pair Button on the receiver
unit. The Pair LED on the receiver will begin
to flash slowly.
4 Within 10 seconds briefly press the Pair
Button inside the SimplyWorks® JOYSTICK
battery compartment.
5 After a short period the Pair LED on the
receiver unit will light steadily for 5 seconds
indicating pairing is complete.
6 If the Pair LED stops flashing, and does
not light steadily, repeat the procedure
from (3). If it is unsuccessful, please refer
to the Troubleshooting section.
JOYSTICK
Your SimplyWorks® JOYSTICK is compatible with any SimplyWorks® receiver for computer
input and toy control applications.
Compatibility
Remove the battery cover on the underside of the unit. Connect a good quality (such as Duracell
or Energiser) 9-Volt PP3/6F-22 (or equivalent) battery. If you are not intending to use your
SimplyWorks® JOYSTICK for a long time, it is advisable to remove the battery to prevent leakage,
which may damage the product.
Fitting the Battery
Your SimplyWorks® JOYSTICK has four cursor speed settings for use with computer input
applications. To change cursor speed press, and hold down, the Drag Lock button until you hear a
‘beep’, and then release.
To reduce cursor speed press the Left Click button (each press incrementally reduces the speed).
To increase cursor speed press the Right Click button (each press incrementally increases the
speed).
Once you have selected the most suitable cursor speed press and hold down the Drag Lock button
until you hear a ‘beep’. Cursor speed is now set.
Speed Control Setting
Your SimplyWorks® JOYSTICK has no user serviceable parts. If repair is necessary the unit should
be returned to Pretorian Technologies or an authorised distributor.
Maintenance
Features
• State of the art radio link with an
interference free operating range
exceeding 10 metres.
• Uses 2.4 GHz global, licence-free ISM
radio band.
• Light touch joystick movement
(0.5 Newtons).
• Four cursor speed settings
with audible alerts
• Colour coded Left/Right and Drag Lock
buttons mounted sub-flush to prevent
accidental operation.
• Sockets to operate Left/Right click
buttons from remote switches.
• Works with any SimplyWorks®
receiver for computer input or
toy control.
Pairing
SimplyWorks
®
Pair

Before you can use your SimplyWorks®
JOYSTICK it must be paired with one of the
SimplyWorks® receivers (RECEIVE, CONTROL
LITE, CONTROL, CONTROL PRO). To pair the
units use the following procedure:
1 Remove the battery cover on the
SimplyWorks® JOYSTICK.
2 Place the receiver within 1 metre of your
SimplyWorks® JOYSTICK.
3 Briefly press the Pair Button on the receiver
unit. The Pair LED on the receiver will begin
to flash slowly.
4 Within 10 seconds briefly press the Pair
Button inside the SimplyWorks® JOYSTICK
battery compartment.
5 After a short period the Pair LED on the
receiver unit will light steadily for 5 seconds
indicating pairing is complete.
6 If the Pair LED stops flashing, and does
not light steadily, repeat the procedure
from (3). If it is unsuccessful, please refer
to the Troubleshooting section.
JOYSTICK
Your SimplyWorks® JOYSTICK is compatible with any SimplyWorks® receiver for computer
input and toy control applications.
Compatibility
Remove the battery cover on the underside of the unit. Connect a good quality (such as Duracell
or Energiser) 9-Volt PP3/6F-22 (or equivalent) battery. If you are not intending to use your
SimplyWorks® JOYSTICK for a long time, it is advisable to remove the battery to prevent leakage,
which may damage the product.
Fitting the Battery
Your SimplyWorks® JOYSTICK has four cursor speed settings for use with computer input
applications. To change cursor speed press, and hold down, the Drag Lock button until you hear a
‘beep’, and then release.
To reduce cursor speed press the Left Click button (each press incrementally reduces the speed).
To increase cursor speed press the Right Click button (each press incrementally increases the
speed).
Once you have selected the most suitable cursor speed press and hold down the Drag Lock button
until you hear a ‘beep’. Cursor speed is now set.
Speed Control Setting
Your SimplyWorks® JOYSTICK has no user serviceable parts. If repair is necessary the unit should
be returned to Pretorian Technologies or an authorised distributor.
Maintenance
Features
• State of the art radio link with an
interference free operating range
exceeding 10 metres.
• Uses 2.4 GHz global, licence-free ISM
radio band.
• Light touch joystick movement
(0.5 Newtons).
• Four cursor speed settings
with audible alerts
• Colour coded Left/Right and Drag Lock
buttons mounted sub-flush to prevent
accidental operation.
• Sockets to operate Left/Right click
buttons from remote switches.
• Works with any SimplyWorks®
receiver for computer input or
toy control.
Pairing
SimplyWorks
®
Pair

Symptom Possible Cause / Remedy
Unit not functioning
No cursor movement
LED remains lit
• Units are not paired. Following pairing procedure.
• Batteries flat in SimplyWorks® JOYSTICK.
Replace battery.
• Check USB connection to computer.
• Units may not be paired. Follow pairing procedure.
Units will not Pair - LED
is extinguished after
30 seconds.
• Batteries flat in either toy control receiver or
SimplyWorks® JOYSTICK. Replace battery.
• Ensure SimplyWorks® JOYSTICK is within 1
metre of receiver while pairing.
INSTRUCTIONS
SimplyWorks ®
Pack Contents
Carefully check the contents
of the box, which are:
JOYSTICK
SimplyWorks® is the world's first fully
integrated wireless system specifically for
users with motor skill difficulties.
SimplyWorks® allows you the freedom to
create wire-free, single or multi-user learning
environments, reducing set up time and
allowing you to concentrate on the learning
tasks themselves.
The SimplyWorks® JOYSTICK can be used with
any SimplyWorks® receivers for computer
imput, or to control toys and other battery
operated appliances.
With movement responding to the lightest
touch of the joystick, this is the only wireless
joystick specifically designed for users with
motor skill difficulties.
If your SimplyWorks® JOYSTICK does not operate correctly, please use the following guide to
determine the cause. If, after following this guide, your unit still does not operate, please contact
your supplier before returning it.
Your SimplyWorks® JOYSTICK is warranted for 24 months against defects in manufacture or
component failure. The unit is designed for domestic, educational, commercial and light
industrial applications. Use outside these areas will invalidate the warranty. Unauthorised repair
or modification, mechanical abuse, immersion in any liquid or connection to incompatible
equipment will also invalidate the warranty. Product Description
Troubleshooting
Warranty
Unit works erratically • Batteries flat in either toy control receiver or
SimplyWorks® JOYSTICK. Replace battery.
• Out of range - move receiver unit closer to
SimplyWorks® JOYSTICK.
• Interference - place receiver and
SimplyWorks® JOYSTICK away from sources
of interference.
SimplyWorks
®
JOYSTICK
T-Bar and
Soft Ball handles
This manual
SimplyWorks
®
Unit 37 Corringham Road Industrial Estate
Gainsborough Lincolnshire DN21 1QB United Kingdom
Tel [phone] Fax [phone]
www.pretorianuk.com
SimplyWorks®is a registered trademark of Pretorian Technologies Ltd.
S040019