Price PARC Node User manual

Flush Channel with Diffuser Installation Guide

Flush Channel with Diffuser Installation Guide
1v001 | Flush Channel with Diuser Installation Guide
NODE FLUSH CHANNEL WITH DIFFUSER INSTALLATION GUIDE
v001
© 2020 Price Industries Limited o/a PARC. All rights reserved.
TABLE OF CONTENTS
Product Overview.............................................................................................................................................................. 2
Read and Save These Instructions .................................................................................................................................... 3
Before You Start ................................................................................................................................................................ 3
Tools Required .................................................................................................................................................................. 3
Site Conditions, Storage and Handling Instructions ........................................................................................................... 3
Node Flush Channel Installation Sequence ........................................................................................................................ 4
Access Cables .................................................................................................................................................................. 4
Connecting Node Flush Channel Face to Mounting ........................................................................................................... 5
Connecting Node Flush Channels Together ....................................................................................................................... 5
Node Flush Channel Plenum Installation ............................................................................................................................ 6
End Caps .......................................................................................................................................................................... 7
Cutting Node Channels to Length ..................................................................................................................................... 8
Node Device Installation .................................................................................................................................................... 8
Node Device Removal ....................................................................................................................................................... 8
Waste Disposal Management ............................................................................................................................................ 9

Flush Channel with Diffuser Installation Guide
2v001 | Flush Channel with Diuser Installation Guide
Product Overview
The Node Flush Channel assembly consists of two continuous skirt mounting angles held together by intermittent
mounting brackets, which interfaces with the channel face.
Note: All mounting hardware supplied and installed by others.
Figure 1
The Node Flush Channel with Diuser is designed to be installed between ceiling panels or plasterboard, in applications
with a ceiling void.
The following guide should only be used for Node Flush Channel with Diuser where PARC is providing the diuser and
plenum.
Please refer to our Node Flush Channel Installation Guide if you are installing without the Node diuser or plenum.
It is recommended that the Node Flush Channel length is coordinated with the manufacturer to the required sizes to
match the building design. The Node Flush Channel can be site cut if needed.
Note: All mounting hardware and sub structure is to be supplied and installed alongside the Node Flush Channel.
Lighting and other services must be installed by qualified personnel.
For further information regarding product or installation, please contact [e-mail].
SHEET
1 OF 6
SUBMITTAL
NUMBER
PROJECT
PRICE INDUSTRIES INC.
2975 Shawnee Ridge Court | Suwanee, GA
Phone: [phone]
PRICE INDUSTRIES LTD.
638 Raleigh Street | Winnipeg, MB
Phone: [phone]
PRICE INDUSTRIES (UK) LTD.
Thames Warf Studio | Rainville Road | London, UK
Phone: [phone]
SUBMITTAL
DRAWING TITLE
TOLERANCES UNLESS OTHERWISE SPECIFIED
LINEAR TOLERANCE:
X.X = u 0.06" / X.XX = u 0.03" / X.XXX = u 0.01"
ANGULAR TOLERANCE:
X = u 1 v / X.X = u 0.5 v
SIZE
B
© COPYRIGHT PRICE INDUSTRIES 2019
C2020-03-25 NPT MLH
B2020-03-12 NPT MLH
A2019-11-27 NPT MLH
REV DATE DRAWN BY CHECKED BY
1
3
A B C D E
2
CONSTRUCTION:
- FLUSH CHANNEL
o ALUMINUM EXTRUSION
o ALUMINUM SHEET
o STEEL SHEET
- RECESSED CHANNEL
o ALUMINUM EXTRUSION
o ALUMINUM SHEET
- PLENUM
o
STEEL SHEET
FINISH:
- ALL HARDWARE; MILL FINISH UNLESS OTHERWISE
SPECIFIED
ELECTRICAL SERVICE
- SEE SPECIFIC NODE DEVICE REQUIREMENTS
MECHANICAL SERVICE
-
CONTACT PRICE SALES REPRESENTATIVE
CONTROLS
- CONTROLS BY OTHERS
NOMENCLATURE
- ALL COMPONENTS SHOWN ARE PROVIDED BY PRICE
UNLESS OTHERWISE NOTED
- ( INSTL BY OTHERS ): PROVIDED BY PRICE AND
INSTALLED BY OTHERS
- ( BY OTHERS ): PROVIDED AND INSTALLED BY OTHERS
- TBC: DETAILS TO BE CONFIRMED
NOTES:
- PRODUCT FINISH MAY VARY IN TONE, GLOSS AND
TEXTURE; VARIATIONS ARE WITHIN PRICE INDUSTRIES’
QUALITY STANDARDS
NODE
NODE CHANNEL
271710
FLUSH CHANNEL
4.72
120
EXPOSED WIDTH
11.81
300
OVERALL WIDTH
CEILING SURFACE
MOUNTING
(BY OTHERS)
.12
3
RECOMMENDED CLEARANCE
W/ SURROUNDING CEILING
4.33
110
CHANNEL HEIGHT
FLUSH CHANNEL WITH DIFFUSER
4.72
120
FACE WIDTH
.58
15
DIFFUSER OPENING
5.88
149
EXPOSED WIDTH
11.81
300
OVERALL WIDTH
MOUNTING
(BY OTHERS)
4.33
110
CHANNEL HEIGHT
.12
3
RECOMMENDED CLEARANCE
W/ SURROUNDING CEILING
CEILING SURFACE
RECESSED CHANNEL WITH DIFFUSER
4.72
120
RECOMMENDED
CEILING OPENING
CEILING SURFACE
11.81
300
OVERALL WIDTH
MOUNTING
(BY OTHERS)
.08
2
CLEARANCE TO
DEVICE FACE
3.07
78
MOUNTING HEIGHT
NODE DEVICE
(ORDERED SEPARATELY)
(INSTL BY OTHERS)
NODE DEVICE
(ORDERED SEPARATELY)
(INSTL BY OTHERS)
NODE DEVICE
(ORDERED SEPARATELY)
(INSTL BY OTHERS)
CHANNEL TYPES

Flush Channel with Diffuser Installation Guide
3v001 | Flush Channel with Diuser Installation Guide
Read and save these instructions before beginning to install the Node Flush Channel with Diuser.
Warning! To reduce the risk of re, electric shock, or injury to persons, observe the following:
• When cutting or drilling into wall or ceiling do not damage electrical wiring and other hidden utilities
• Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the
manufacturer at [e-mail].
Before You Start
Inspect all product parts for aws and shipping damage.
If anything is discovered to be damaged, contact the shipping company and manufacturer immediately.
Tools Required
Site Conditions, Storage and Handling
Read this guide before handling the product.
• Read the Installation Guide before handling.
• Always wear appropriate hand protection when handling.
• Only store in clean dry conditions.
• Do not over stack.
• Do not stack in a way likely to cause falls.
Poor or rough handling, rolling or dropping of the product on corners or edges may cause damage to the product or
cause the product to deteriorate.
Lengths of Node should not span between points as any load applied mid-span may cause product damage.
Site storage of items should be at, preferably on a suitable pallet (supporting the entire length of the Node Flush
Channel with Diuser) without additional top loading.
Consideration should be given to the advice of the Site Occupational Health and Safety Representative regarding
manual handling. An assessment should be made of any risk and if necessary mechanical lifting equipment should be
used.
The storage space must be cleared of debris and, in general, should be enclosed. The Node Flush Channel with Diuser
should be kept clean, dry and protected from the elements.
Site conditions should be prepared for installation of the Node Flush Channel with Diuser. The site should be clean, dry
and clear of other trades working in the ceiling void.
Flush Channel with Diffuser
Installation Guide
3
Flush Channel with Diffuser Installation Guide
Read and Save these Instructions before beginning to install Node Flush Channel with Diffuser:
Warning! To reduce the risk of fire, electric shock, or injury to persons, observe the following:
•When cutting or drilling into wall or ceiling do not damage electrical wiring and other hidden utilities.
•Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the
manufacturer [e-mail].
Before You Start:
Inspect all product parts for flaws and shipping damage.
If anything is discovered to be damaged, contact the shipping company and manufacturer immediately.
Node Flush Channel with Diffuser Installation Tools Required:
Site Conditions, Storage & Handling:
Read This Guide before handling the product.
•Read the Installation guide before handling.
•Always wear appropriate hand protection when handling.
•Only store in clean dry conditions
•Do not over stack.
•Do not stack in a way likely to cause falls.
Poor or rough handling, rolling or dropping of the product on corners or edges may cause damage to the product or
cause the product to deteriorate.
Lengths of node should not span between points as any load applied mid-span may cause product damage.
Site storage of items should be flat, preferably on a suitable pallet (supporting the entire length of the Node Flush
Channel with Diffuser) without additional top loading.
Consideration should be given to the advice of the Site Occupational Health & Safety Representative regarding manual
handling. An assessment should be made of any risk and if necessary mechanical lifting equipment should be used

Flush Channel with Diffuser Installation Guide
4v001 | Flush Channel with Diuser Installation Guide
Node Flush Channel Installation Sequence
Before installing the Node Channel, ensure whenever possible, there is access to both sides.
The Node Flush Channel with Diuser assembly consists of two mounting angles held together by intermittent
mounting brackets which interfaces with the channel face.
Figure 2
Suspend the mounting angles and mounting brackets at the required level.
Fix suspension hangers to the mounting angles using the slots provided in the mounting angles.
It is recommended that the Node Flush Channel is supported no more than 150mm from an end or 150mm from any
joint.
Access Cables
Once the mounting assembly is installed, attach the Node access cables to the bridging plate in the mounting assembly
through the hole provided.
Before connecting the channel face to the mounting assembly, connect the other end of the Node access cable to the
ange on the inside of the channel face in the hole provided.
When lowering the channel onto access cable, the face should be lowered gently to avoid damage, ensuring that there
is no-one standing below.
SHEET
2 OF 6
SUBMITTAL
NUMBER
PROJECT
PRICE INDUSTRIES INC.
2975 Shawnee Ridge Court | Suwanee, GA
Phone: [phone]
PRICE INDUSTRIES LTD.
638 Raleigh Street | Winnipeg, MB
Phone: [phone]
PRICE INDUSTRIES (UK) LTD.
Thames Warf Studio | Rainville Road | London, UK
Phone: [phone]
SUBMITTAL
DRAWING TITLE
TOLERANCES UNLESS OTHERWISE SPECIFIED
LINEAR TOLERANCE:
X.X = u 0.06" / X.XX = u 0.03" / X.XXX = u 0.01"
ANGULAR TOLERANCE:
X = u 1 v / X.X = u 0.5 v
SIZE
B
© COPYRIGHT PRICE INDUSTRIES 2019
C2020-03-25 NPT MLH
B2020-03-12 NPT MLH
A2019-11-27 NPT MLH
REV DATE DRAWN BY CHECKED BY
1
3
A B C D E
2
CONSTRUCTION:
- FLUSH CHANNEL
o ALUMINUM EXTRUSION
o ALUMINUM SHEET
o STEEL SHEET
- RECESSED CHANNEL
o ALUMINUM EXTRUSION
o ALUMINUM SHEET
- PLENUM
o
STEEL SHEET
FINISH:
- ALL HARDWARE; MILL FINISH UNLESS OTHERW ISE
SPECIFIED
ELECTRICAL SERVICE
- SEE SPECIFIC NODE DEVICE REQUIREMENTS
MECHANICAL SERVICE
-
CONTACT PRICE SALES REPRESENTATIVE
CONTROLS
- CONTROLS BY OTHERS
NOMENCLATURE
- ALL COMPONENTS SHOWN ARE PROVIDED BY PRICE
UNLESS OTHERWISE NOTED
- ( INSTL BY OTHERS ): PROVIDED BY PRICE AND
INSTALLED BY OTHERS
- ( BY OTHERS ): PROVIDED AND INSTALLED BY OTHERS
- TBC: DETAILS TO BE CONFIRMED
NOTES:
- PRODUCT FINISH MAY VARY IN TONE, GLOSS AND
TEXTURE; VARIATIONS ARE WITHIN PRICE INDUSTRIES’
QUALITY STANDARDS
NODE
NODE CHANNEL
271710
FLUSH CHANNEL ISOMETRIC VIEW
FLUSH CHANNEL TOP VIEW
118.11
3000
MAX LENGTH
9.84
250
MOUNTING WIDTH
5.91
150 MOUNTING SLOT SPACING
SLOT DIMENSIONS
10MM X 25MM
35.43
900
MAX RECOMMENDED
SUPPORT SPACING
GENERAL CONTRUCTION - FLUSH CHANNEL
Figure 3
ACCESS CABLES
BRIDGING PLATE

Flush Channel with Diffuser Installation Guide
5v001 | Flush Channel with Diuser Installation Guide
Connecting Node Flush Channel Face to Mounting
Connect the Node Flush Channel with Diuser face to the mounting brackets by pushing into place until you hear a
click.
Figure 4
Connecting Node Flush Channels Together
Node Flush Channels can be connected together by way of key stock splicing the connection joint and fastening into
place.
Figure 5
Connect all required sections ensuring no visible gap between both sections.
MOUNTING BRACKET
CHANNEL FACE
ALIGNMENT TAB AND FASTENERS
(INSTALLATION BY OTHERS)
INSTALL ALIGNMENT BAR AFTER CHANNELS
ARE IN PLACE WITH SELF-DRILLING HARDWARE

Flush Channel with Diffuser Installation Guide
6v001 | Flush Channel with Diuser Installation Guide
Node Flush Channel Plenum Installation
Install Node Flush Channel Plenum by xing to the Node Flush Channel continuous skirts and mounting angles.
If a Plenum is being located above an alignment plate then the alignment plate must be removed prior to plenum
installation to ensure correct diuser operation.
Figure 6
The nal installation should be as below.
Figure 7
FLUSH CHANNEL PLENUM
SELF-DRILLING FASTENER
S
ALIGNMENT PLATE

Flush Channel with Diffuser Installation Guide
7v001 | Flush Channel with Diuser Installation Guide
End Caps
The Node Flush Channel can be provided with or without end caps as project design requirements. End caps are factory
installed as required.
Figure 8
Figure 9
SHEET
6 OF 6
SUBMITTAL
NUMBER
PROJECT
PRICE INDUSTRIES INC.
2975 Shawnee Ridge Court | Suwanee, GA
Phone: [phone]
PRICE INDUSTRIES LTD.
638 Raleigh Street | Winnipeg, MB
Phone: [phone]
PRICE INDUSTRIES (UK) LTD.
Thames Warf Studio | Rainville Road | London, UK
Phone: [phone]
SUBMITTAL
DRAWING TITLE
TOLERANCES UNLESS OTHERWISE SPECIFIED
LINEAR TOLERANCE:
X.X = u 0.06" / X.XX = u 0.03" / X.XXX = u 0.01"
ANGULAR TOLERANCE:
X = u 1 v / X.X = u 0.5 v
SIZE
B
© COPYRIGHT PRICE INDUSTRIES 2019
C2020-03-25 NPT MLH
B2020-03-12 NPT MLH
A2019-11-27 NPT MLH
REV DATE DRAWN BY CHECKED BY
1
3
A B C D E
2
CONSTRUCTION:
- FLUSH CHANNEL
o ALUMINUM EXTRUSION
o ALUMINUM SHEET
o STEEL SHEET
- RECESSED CHANNEL
o ALUMINUM EXTRUSION
o ALUMINUM SHEET
- PLENUM
o
STEEL SHEET
FINISH:
- ALL HARDWARE; MILL FINISH UNLESS OTHERWISE
SPECIFIED
ELECTRICAL SERVICE
- SEE SPECIFIC NODE DEVICE REQUIREMENTS
MECHANICAL SERVICE
-
CONTACT PRICE SALES REPRESENTATIVE
CONTROLS
- CONTROLS BY OTHERS
NOMENCLATURE
- ALL COMPONENTS SHOWN ARE PROVIDED BY PRICE
UNLESS OTHERWISE NOTED
- ( INSTL BY OTHERS ): PROVIDED BY PRICE AND
INSTALLED BY OTHERS
- ( BY OTHERS ): PROVIDED AND INSTALLED BY OTHERS
- TBC: DETAILS TO BE CONFIRMED
NOTES:
- PRODUCT FINISH MAY VARY IN TONE, GLOSS AND
TEXTURE; VARIATIONS ARE WITHIN PRICE INDUSTRIES’
QUALITY STANDARDS
NODE
NODE CHANNEL
271710
NODE DEVICE LAYOUT
REFLECTED CEILING PLAN
DEVICE 1
DEVICE 2
DEVICE 3
DEVICE 4
DEVICE 5
MOUNTING BRACKETS AND HOUSINGS PROVIDED
AND INSTALLED FOR SPECIFIED DEVICE TYPES
BLANK NODE -
CAMERA -
DOWNLIGHT 5
EMERGENCY LIGHT -
LINEAR LIGHT -
ROSE NODE -
SENSOR -
SPEAKER -
SPOTLIGHT -
SPRINKLER -
AVAILABLE DEVICE TYPES NOTES
POWDER
COAT
BLACK - PRICE B17
WHITE - RAL9016
WHITE - RAL9010
ANODIZED
MATTE
CLEAR
CHAMPAGNE
LIGHT BRONZE
MEDIUM BRONZE
DARK BRONZE
BLACK
AVAILABLE CHANNEL FINISHES
BLACK POLYMER - PRICE B17
WHITE POLYMER - RAL9016
DEVICE HOUSING COLOR
(RECESSED CHANNEL ONLY)
NOTES:
DEVICES ORDERED SEPARATELY
MAXIMUM 5 DEVICES PER CHANNEL (FOR ADDITIONAL DEVICES, CONTACT
YOUR SALES REPRESENTATIVE)
MINIMUM DEVICE SPACING FROM END OF CHANNEL: 150MM EDGE TO EDGE
TYPICAL MINIMUM SPACING BETWEEN DEVICES: 30MM EDGE TO EDGE
DOWNLIGHT NOT AVAILABLE WITH TRIMLESS RECESSED CHANNEL
FOR THIRD PARTY DEVICE INTEGRATION PLEASE CONTACT YOUR SALES
REPRESENTATIVE
1
2
3
4
5
6
END CAP DETAIL VIEW
RECESSED CHANNEL
LEFT AND RIGHT
RIGHT
LEFT
END CAP OPTIONS
END CAP LAYOUT
REFLECTED CEILING PLAN
LEFT RIGHT
END CAP
DEVICE INTEGRATION AND CHANNEL FINISH
END CAP DETAILS
DEVICES CAN BE PLACED
ANYWHERE ALONG THE
LENGTH OF THE CHANNEL
(SEE NOTES FOR DETAILS)
END CAP DETAIL VIEW
FLUSH CHANNEL WITH DIFFUSER
END CAP
END CAP DETAIL VIEW
FLUSH CHANNEL
END CAP
END CAP DETAIL VIEW
FLUSH CHANNEL WITH DIFFUSER
END CAP
HA
RDWARE

Flush Channel with Diffuser Installation Guide
8v001 | Flush Channel with Diuser Installation Guide
Cutting Node Channels to Length
Where possible, the channel should be ordered to length based upon contractor site measurements.
If the channel must be cut to length, this should be done at the end, rather than a joint, to minimize visual impact. The
end cap should be removed and reattached after cutting the channel. The maximum length that can be trimmed is
dened by the position of the bridge bracket.
Node Device Installation
Node devices can be integrated into the system at design stage and can be purchased separately from the Node
Channel.
Outer Node housings will be factory installed in the required locations.
The Node devices are installed in the housing by aligning the snap tabs and pushing the inner casing directly into the
housing.
Figure 10
Node Device Removal
To remove the Node device, insert the Node removal tool into the shadow gap between the outer housing and device.
Persuasively slide the Node removal tool anti-clockwise until the Node device is released.
Figure 11
INSERT NODE DEVICE
INTO HOUSING

Flush Channel with Diffuser Installation Guide
9v001 | Flush Channel with Diuser Installation Guide
Waste Disposal Management
PARC Node Flush Channels are shipped and packaged with protective material that should be disposed of in an
appropriate manner.
Please remove or recycle waste and packaging materials as per your local waste disposal requirements.
The information contained in this document only provides guidance for the installation of PARC products. All PARC
products should only be installed by trained professionals and installation responsibility remains with the installer. PARC
reserves the right to review, alter, amend or remove published data without notice as our policy is one of constant
improvement. Whilst PARC will endeavor to keep its publications up to date, readers will appreciate that between
publications there will be changes in laws or other developments aecting the accuracy of the information contained in
this installation guide.