Pride Wrangler User manual

Serial #
MV600
OWNER’S MANUAL
USA
182 Susquehanna Avenue
Exeter, PA 18643-2694
Canada
5096 South Service Road
Beamsville, Ontario L0R 1B3
Australia
20-24 Apollo Drive
Hallam, Victoria 3803
www.pridemobility.com.au
New Zealand
38 Lansford Crescent
Avondale
Auckland, New Zealand 1007
www.pridemobility.co.nz
UK
32 Wedgwood Road
Bicester, Oxfordshire OX26 4UL
www.pride-mobility.co.uk
B.V.
(Authorised EU Representative)
De Zwaan 3
1601 MS Enkhuizen
The Netherlands
www.pride-mobility.nl
Italy
Via del Progresso, ang.Via del Lavoro
Loc. Prato della Corte
00065 Fiano Romano (RM)
www.pride-italia.it
France
26 rue Monseigneur Ancel
69 800 Saint-Priest
www.pridemobility.fr
Spain
Calle Velazquez 80 6D
28001 Madrid
www.pridemobility.com

4SAFETY GUIDELINES
Copyright © 2019
INFMANU5056/Rev A/February 2019
WARNING! An authorized Pride dealer or qualified technician must perform the initial setup of
this vehicle and must perform all of the procedures in this manual.
The symbols below are used throughout this owner’s manual and on the vehicle to identify warnings and import-
ant information. It is very important for you to read them and understand them completely.
WARNING! Indicates a potentially hazardous condition/situation. Failure to follow designated
procedures can cause either personal injury, component damage, or malfunction. On the
product, this icon is represented as a black symbol on a yellow triangle with a black border.
MANDATORY! These actions should be performed as specified. Failure to perform mandatory
actions can cause personal injury and/or equipment damage. On the product, this icon is
represented as a white symbol on a blue dot with a white border.
PROHIBITED! These actions are prohibited. These actions should not be performed at any
time or in any circumstances. Performing a prohibited action can cause personal injury and/or
equipment damage. On the product, this icon is represented as a black symbol with a red circle
and red slash.
INTENDED USE
The intended use of the mobility device is to provide mobility to persons limited to a seated position that have the
capability of operating a scooter.
NOTE: This owner’s manual is compiled from the latest specifications and product information available at
the time of publication. We reserve the right to make changes as they become necessary. Any changes to our
products may cause slight variations between the illustrations and explanations in this manual and the product
you have purchased. The latest/current version of this manual is available on our website.
NOTE: This product is compliant with WEEE, RoHS, and REACH directives and requirements.
NOTE: This product meets IPX4 classification (IEC 60529).
NOTE: The MV600 and its components are not made with natural rubber latex. Consult with the manufacturer
regarding any after-market accessories.
Dealer:
Address:
Phone Number:
Purchase Date: Serial Number:
Please fill out the following information for quick reference:

MV600 3
CONTENTS
SAFETY GUIDELINES ............................................................................................... 2
I. SAFETY ............................................................................................................ 4
II. YOUR VEHICLE ............................................................................................... 7
III. BATTERIES AND CHARGING .......................................................................... 15
IV. OPERATION ................................................................................................... 22
V. COMFORT ADJUSTMENTS ............................................................................ 24
VI. DISASSEMBLY AND ASSEMBLY .................................................................... 28
VII. BASIC TROUBLESHOOTING ......................................................................... 29
VIII. CARE AND MAINTENANCE ........................................................................... 31

4 MV600
Manufactured in
Fully charge batteries before operating.
Remove key from an unattended vehicle.
Battery Set Configuration:
+ = Positive (Red) Terminal Post
- = Negative (Black) Terminal Post
Connect Red wires to Red Positive (+) Terminal Posts.
Connect Black wire to Black Negative (-) Terminal Posts.
Read and follow the information in the owner’s manual.
I. SAFETY
PRODUCT SAFETY SYMBOLS
The symbols below are used on the vehicle to identify warnings, mandatory actions, and prohibited actions. It is
very important for you to read and understand them completely.
NOTE: There are more warnings identified and explained in the Consumer Safety Guide that is included with
your vehicle. Please become familiar with all the warnings and safety information found in the Consumer
Safety Guide and refer to this resource often.
Indicates UNOCCUPIED vehicle securement points
Does not meet ISO 7176-19 standards for occupied transport in a motor
vehicle. When travelling in a motor vehicle, do not sit in your vehicle.
MODEL #
Vehicle information label

MV600 5
I. SAFETY
GENERAL
MANDATORY! Do not operate your new vehicle for the first time without completely reading and
understanding this owner’s manual and the Consumer Safety Guide.
Your vehicle is a state-of-the-art product. We provide an extensive variety of products to best fit the individual
needs of the vehicle user.
There are certain situations where the vehicle user will need to practice operating the vehicle.
As you begin using your vehicle during daily activities, you will probably encounter situations in which you will
need some practice. Simply take your time and you will soon be in full and confident control as you maneuver
through doorways, on and off elevators, up and down ramps, and over moderate terrain.
Additional general information can be found on the supplemental information sheets and booklets included in your
Owner’s Package. Please fully read and review the information, and keep it readily available for future reference.
Below are some precautions, tips and other safety considerations that will help you become accustomed to operating
the vehicle safely.
PRE-RIDE SAFETY CHECK
Get to know the feel of your vehicle and its capabilities. We recommend that you perform a safety check before
each use to make sure your vehicle operates smoothly and safely.
Perform the following inspections prior to using your vehicle:
Check the condition of the tires. Make sure they are not damaged or excessively worn.
Check all electrical connections. Make sure they are tight and not corroded.
Check all harness connections. Make sure they are secured properly.
Check the brakes to ensure they operate properly.
Check the battery condition meter to ensure the batteries are fully charged.
Ensure the manual freewheel lever is in drive mode before sitting on the vehicle.
If you discover a problem, contact your authorized dealer for assistance. Please refer to the Contact Information
insert in your Owner’s Package.
BRAKING INFORMATION
Your vehicle is equipped with these powerful brake systems:
Regenerative: Uses electricity to rapidly slow the vehicle when the throttle control lever returns to the center/
stop position.
Disc Park Brake: Activates mechanically after regenerative braking slows the vehicle to near stop or when
power is removed from the system for any reason.
Handbrake: This lever provides you with emergency stopping power. See II. “Your Vehicle.”

6 MV600
I. SAFETY
HANDBRAKE LEVER
The handbrake lever contains hydraulic fluid. When the lever is depressed, the fluid is pushed through the brake
line to engage the brake pads against the brake discs. The handbrake lever is a completely sealed unit, meaning
that the hydraulic fluid should not leak; however, there are certain safety measures that should be taken if the
handbrake lever becomes cracked or damaged.
Do not touch spilled material unless wearing protective equipment, such as safety goggles and gloves.
For small spills, cover the material with dry earth, sand or other non-combustible absorbent material. Once
absorbed, enclose the material in a plastic bag and contact your local waste disposal agency for proper disposal
measures. Do not expose the material to waterways or sewers.
If the eyes are exposed, check for and remove contact lenses. Flush eyes with cool, clean, low-pressure water
while occasionally lifting and lowering the eyelids. Seek medical attention if excessive tearing, redness or
pain persists.
If the skin is exposed, remove all contaminated clothing. Wipe off excess material and wash exposed skin
with soap and water. Seek medical attention if skin appears damaged or if irritation persists. Thoroughly clean
contaminated clothing before reuse. Discard contaminated leather goods.
If ingested, do not induce vomiting or give anything to drink unless directed to by a physician. Never give
anything by mouth to a person who is not fully conscious. Seek medical attention immediately.
If inhaled, move the affected individual to fresh air. If the affected individual is not breathing, immediately
begin rescue breathing. If breathing is difficult, 100% humidified oxygen should be administered by a qualified
individual. Seek medical attention immediately and keep the affected individual warm and at rest.
If ignited, use dry chemical, foam, carbon dioxide or water fog to extinguish.
WARNING! Do not modify the handbrake lever or attempt to replace the hydraulic fluid. If damage
occurs, follow the safety information in this section and contact your authorized dealer for
handbrake replacement. The hydraulic handbrake should only be serviced or replaced by your
authorized dealer.
WARNING! The handbrake contains hydraulic fluid that can cause mild skin, eye and nasal/
bronchial irritation. Do not attempt to adjust or service the handbrake without proper protective
equipment such as safety goggles and gloves and wash hands after handling.

MV600 7
II. YOUR VEHICLE
TILLER CONSOLE
The tiller console houses all of the controls needed to drive your vehicle, including the LCD control panel,
handbrake lever, tiller adjustment lever, and the throttle control lever. See figure 1.
PROHIBITED! Do not expose the tiller console to moisture. In the event that the tiller console
does become exposed to moisture, do not attempt to operate your vehicle until the tiller console
has dried thoroughly.
IDENTIFICATION KEY
Figure 1.Tiller Console
Horn Buttons
These buttons activate a warning horn. Your vehicle must be powered up for the horn to be operational. Do not
hesitate to use the warning horn when doing so may prevent accident or injury.
Speed Adjustment Buttons
These adjustment buttons enable you to pre-select and limit your vehicle’s speed. This is indicated by the maximum
speed indicator on the LCD screen.
Press the image of the tortoise to decrease the speed of the vehicle.
Press the image of the rabbit to increase the speed of the vehicle.
Turn Signal Buttons
Press the appropriate turn signal button once to activate it. The turn signal will flash on the LCD screen.
Press the same signal button to turn it off.
14
5
5
8
9
86
4
7
4
11 32
101112
13
8
15
1. HORN BUTTON
2. SPEED ADJUSTMENT
(INCREASE)
3. SPEED ADJUSTMENT
(DECREASE)
4. TURN SIGNAL BUTTONS
5. THROTTLE CONTROL LEVER
6. HI-LOW SWITCH
7. LIGHTS BUTTON
8. MIRROR AND MIRROR PLUGS
9. HANDBRAKE LEVER
10. MODE BUTTON
11. HAZARD LIGHTS BUTTON
12. SET BUTTON
13. LCD SCREEN
14. TILLER ADJUSTMENT LEVER
15. BRAKE LOCK

8 MV600
II. YOUR VEHICLE
Throttle Control Lever
This lever allows you to control the forward speed and the reverse speed of your vehicle up to the maximum speed
you preset with the speed adjustment. A throttle control lever is located on the underside of the left and right side
of the tiller handle. See figure 1.
To use throttle control lever:
To move Forward, use either of the following:
Use your left thumb to push the left side of the throttle control lever.
Use your right hand fingers to pull back on the right side of the throttle control lever.
To move Rearward, use either of the following:
Use your right thumb to push the right side of the throttle control lever.
Use your left hand fingers to pull back on the left side of the throttle control lever.
Release the throttle control lever and allow your vehicle to come to a complete stop before engaging the other side
of the lever. When the throttle control lever is completely released, it automatically returns to the center “stop”
position and engages your vehicle’s brakes.
High-Low Button
This button toggles the vehicle’s speed between HIGH and LOW.
Press the High-Low button once to set the speed adjustment to high. The High-Low indicator will display on
the LCD screen. See figure 1. Using this setting in conjunction with the speed adjustment buttons will allow
the vehicle to achieve speeds up to the maximum preprogrammed speed for the vehicle.
Press the High-Low button again to set the speed adjustment to Low. The High-Low indicator will not display
on the LCD screen. Using this setting in conjunction with the speed adjustment buttons will allow the vehicle
to achieve speeds up to the half the maximum preprogrammed speed for the vehicle.
Lights Switch
This switch controls your vehicle’s lighting system.
Press the lights button once to activate the lighting system. The light symbol will be shown on the LCD screen.
Press the lights button again to turn the lighting system off.
WARNING! Vehicle users are required to use their lights when visibility is restricted—day or night.
Hazard Lights Button
This button activates the 4-way yellow flashers on your vehicle.
Press the button once to turn on the flashers.
Press the button again to turn off the flashers.
NOTE: The 4-way flashers will flash and a warning beep will sound as long as the hazard lights are on. See
figure 6 for volume control.
Tiller Adjustment Lever
For information on positioning and adjusting your tiller, see V. “Comfort Adjustments.”
Mirror Positioning and Adjustment
For information on positioning and adjusting your mirror, see V. “Comfort Adjustments.”

MV600 9
II. YOUR VEHICLE
IDENTIFICATION KEY
IDENTIFICATION KEY
1. KEY SWITCH
2. OFF-BOARD CHARGER PORT
3. TILLER CONSOLE FUSES
1. OFF-BOARD CHARGER PORT
2. USB PORT
3. BATTERY FUSE
4. KEY FUSE
Figure 3. Lower Tiller Components
Figure 4. Off-board Charger Port/Tiller Console Fuses
Figure 2. Handbrake Lever and Brake Lock (in the
Locked Position)
LCD Screen and control panel settings
The LCD control panel offers easily intuited feedback
information via the LCD screen. See figure 1. The LCD
screen is also used during the set-up (activation) of the
various control panel settings.
Handbrake Lever
This lever provides you with emergency stopping power.
When in motion, release the throttle control lever and gently
squeeze the handbrake lever to come to a stop. Handbrake
effectiveness can be modified by tightening or loosening
the setscrew located on the handbrake lever. See figure 2.
The handbrake can be locked and used as as a parking brake
by squeezing the handbrake lever fully and moving the
brake lock to the locked position. See figure 2. To release
the brake lock, fully squeeze the handbrake.
WARNING! The handbrake is intended for
use as an emergency brake and/or parking
brake only.
Mode Button
Use the mode button to scroll between the odometer,
tripometer, temperature, and clock.
Off-board Charger Port
The off-board charger power cord plugs into this port during
battery charging. The off-board charger port is located on
the tiller.
Key Switch
Insert the key into the key switch and turn it clockwise
to power up (turn on) your vehicle.
Turn the key anticlockwise to power down (turn off)
your vehicle.
WARNING! If the key is turned to the “off”
position while your vehicle is in motion,
the electronic brakes will engage and your
vehicle will come to an abrupt stop!
Electrical System Fuses
Your vehicle is equipped with a series of electrical system
fuses, which help protect the off-board charging system,
key switch and lighting system from receiving an overload
of electrical current. These fuses are the same type used in
automobiles and are located in a compartment on the tiller.
NOTE: Keep all electrical areas clean and free of moisture
and foreign material.
IDENTIFICATION KEY
1. HANDBRAKE LEVER
2. SETSCREW
3. BRAKE LOCK
3
1
2
1
2
3
1
2
4
3

10 MV600
LCD SCREEN AND CONTROL PANEL SETTINGS
The LCD control panel offers easily intuited feedback information via the LCD screen. See figure 5. The LCD
screen is also used during the set-up (activation) of the various control panel settings. See chart 1.
II. YOUR VEHICLE
IDENTIFICATION KEY
Figure 5. LCD Screen
1. BATTERY CONDITION INDICATOR
2. LIGHTS INDICATOR
3. SPEED/ERROR CODE/VOLUME
4. HI-LOW INDICATOR
5. UNIT INDICATOR
6. MAXIMUM SPEED INDICATOR
7. RIGHT TURN INDICATOR
8. AM/PM
9. CLOCK
10. TEMPERATURE
11. DISTANCE/TIME/TEMP/ERROR MESSAGE
12. TRIPOMETER
13. ODOMETER
14. LEFT TURN INDICATOR
10121314 11 97 8
6
5
4
32
1
NOTE: To program control panel settings, Hi-Low Indicator must be switched off, and Maximum Speed
Indicator must be set to full.