Primera AP550 User manual

AP550 Quick Start
LABEL APPLICATOR
Mode
Recall/
Reset
+-
AUnpack and Setup
1. Remove the AP550 from its packaging.
2. Remove all items from the supply box.
3. Place the unit toward the back of a
table with a depth of 30” [76 cm] or
more.
4. Connect the power and switch on the
AP550.
Power CordPower Adapter
30” [76 cm] or more
Power Switch
Power Input (12v)
BLoad Label Stock
5. Place the label roll on the Roll Bar as shown. For narrow rolls you may have to flip guides so
the “L” faces away from the roll on each side.
6. Place the Roll Drag Arm under the Roll Bar so that the rounded tip is near the center of the roll.
7. Place the Roll Bar with labels on the pins so that the bar is fully seated on the pins.
8. Remove approximately 15” [38 cm] of labels from the liner.
labels facing up holes to the rear
Roll Bar
Roll Guides
Roll Drag Arm
AP550
LABEL APPLICATOR
Mode Recall
Reset
+-
15”
[38 cm]
9. Load the label stock according to the diagram below:
Label Path
Liner Drive Roller
Label Guide Roller
Liner Idler Roller Application Roller
Peel Edge
511373-101013

BLoad Label Stock (continued) CLabel/Container Settings (for die-cut labels)
19. Start Labeling
10. Align the leading edge of the label stock
with the roll as shown.
11. Make sure the labels will be fed under the
Sensor Location Line.
12. Move the Guide Collars so they are close
to, but not pinching the label stock.
13. Lock the labels in place by pushing up on
the metal Liner Idler Roller. Make sure there
are no labels past the Liner Drive Roller.
14. Move the Application Arm to the appropriate height by
squeezing the Pin Release Bar and pulling up on the arm.
Distance from
label stock to
arm side plate
should be
equal in these
locations.
Sensor Location Line
Guide Collars
Align Here
Unlock
Lock
Liner Idler Roller
Liner Drive Roller
Position Container Height
Notch 4 6” - 8” [15-20 cm]
Notch 3 4” - 6” [10-15 cm]
Notch 2 2” - 4” [5-10 cm]
Notch 1 0” - 2” [0-5 cm]
Pin Release Bar
Pin
15. Access Label/Container Settings
16. Sensor Calibration
17. Platform Position
18. Guide Position
Mode Recall/
Reset +-Mode Recall/ Reset +-
Press “Mode” once. When “F 0” is displayed hold
“Mode” for 2 seconds to access
Label/Container Settings.
Mode Recall/
Reset +-Mode Recall/ Reset +-
Press “Recall/
Reset” twice.
Push down on arm until
“0.00” is displayed.
“SC-” is displayed.
LABEL APPLICATOR
Mo
Re
Push here
Mode Recall/
Reset +-Mode Recall/
Reset +-Mode Recall/
Reset +-
LABELAPPLICATOR
Mode
Recall/
Reset
+-
Press “Recall/
Reset” twice.
“PPo” is displayed. Load the container. Press and hold “+” or “-”
to move the platform to the
desired labeling position.
Mode Recall/
Reset +-Mode Recall/ Reset +-Mode Recall/ Reset +-
LABELAPPLICATOR
Mode
Recall/
Reset
+-
Press “Recall/
Reset” once.
“gPo” is displayed.
Container
Guide
Loosen the Thumb Screw
under the platform to
adjust the guide
side-to-side.
Thumb Screw
under platform
Press “Mode” to
store settings.
LABELAPPLICATOR
Mode
Recall/
Reset
+-
Lower the Application Arm quickly until it
touches the container.
The platform will move toward you.
Maintain downward force on the arm until
the label is completely applied.
Push here
15a 15b
16a 16b 16c
17a 17b 17c 17d
18a 18b 18c 18d
no labels here