Primera Bravo II User manual

SECTION I: SETUP
1. Check to make sure the following items are enclosed:
•Output Bin Holder
•Output Bin
•Teflon Tape Strips
•Operators Manual and
other information
2. Attaching the Output Bin
•After the software has
been updated, you will
need to attach the
Output Bin Holder
and Output Bin to the
Bravo to collect the
finished discs. Attach
the Output Bin Holder
as shown, aligning the
Locating Tabs on the
Output Bin Holder with
the Slots located on the
underside of the Bravo
allowing the holder to
hang off the edge of the
table. Notice the slots
do allow for adjusting
the position of the out-
put bin. If your discs
are not falling into the
bin, you will be able to
move the bin slightly to
align it.
•Place the Output Bin on
the Output Bin Holder
as shown.
•Your kit comes with
Teflon coated tape strips.
These may be necessary
if the discs you use do
not slide freely down
the Output Chute into
the Output Bin. Apply
the strips to the ribs of
the Chute as shown,
starting at the top of the
chute, and continuing
on down to the lower lip of the Chute to reduce friction and
cause the discs to eject properly.
SECTION II: ENABLING KIOSK MODE
Kiosk mode is available both in PrimoDVD and in the driver as a
printing option. This allows you to use the Kiosk Mode for full CD
production as well as print-only jobs.
Using Kiosk Mode in PrimoDVD
In PrimoDVD, click Robotics then Options. You will see the
following window:
Using Kiosk Mode in the Print Driver
If you are using the Bravo AutoPrinter,
or just want to print discs and have
them eject out the front of the unit, you
can enable Kiosk Mode in the driver as
well. In the Driver Settings you will see
a new option, Disc Output Location.
Simply set this to Kiosk Mode. If you
Thank you for purchasing the Kiosk Kit for the Bravo™ Disc
Publisher. This will enable your Bravo to use both the right and left
bins as input, doubling the capacity of your Bravo. This sheet
describes the installation and use of the Kiosk Kit.
Output Bin
Holder
Output Chute
Output Bin
Slots
Locating Tabs
Lower Lip of Chute
Output Chute
Ribs
Start Tape Here
Output Holder
Output Bin
Click the Enable Kiosk
Mode Check Box to use
this feature.

are creating jobs in PrimoDVD, it is not necessary to change this
driver setting if you already have set Kiosk Mode active under
Robotic Options. The PrimoDVD Kiosk Mode option overrides any
driver setting.
NOTE: In print-only jobs, you may see a Windows "Time Out" error
when the Bravo is out of discs in one bin and switches over to the other.
This is normal, and will not affect the completion of the print job. The
Bravo will retry automatically requiring no operator intervention.
Using Kiosk Mode in Discribe
Set up your job as described in
your Bravo Disc Publisher
Macintosh User's Manual. In
the Robot Write pane you will
see a check box option that will
enable Kiosk Mode.
Using Kiosk Mode in the Mac
Print Driver
If you are using the Mac Bravo
AutoPrinter, or just want to print
discs and have them eject out
the front of the unit, you can
enable Kiosk Mode in the driver
as well.
Click Print Setup to
see the driver pane
and all of its
settings. You will
want to click the
Copies and Pages
button and select
Publisher Settings
option in the drop-
down menu to
see the full pane
and access all the
printer driver settings. At the bottom of the Settings pane you
will see a check box that will enable Kiosk Mode.
Congratulations! You are now ready to use Kiosk Mode, doubling
the capacity of your Bravo Disc Publisher or Bravo AutoPrinter!
Kiosk Kit
For use with Bravo™ Disc Publisher
Operator's Instructions
012204-510710
2003 All rights reserved