Pro Breeze PB-H14 User manual

Instruction Manual
PB-H14
Digital Oil-Free Radiator
IMPORTANT INSTRUCTIONS
- RETAIN FOR FUTURE USE
This product is only suitable for well insulated space or occasional use.

1 | English
Thank you for choosing to purchase a product from Pro Breeze. Please read the entire manual
carefully prior to rst use and keep in a safe place for future reference.
SAFETY INSTRUCTIONS
―
PLEASE READ AND SAVE THESE
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic
safety precautions should always be followed
to reduce the risk of re, electric shock, and
injury to persons, including the following:
WARNING: DO NOT
COVER THE HEATER.
WARNING: TO AVOID THE RISK
OF ELECTRICAL SHOCK, FIRE OR
INJURY TO PEOPLE, ALWAYS MAKE
SURE THE HEATER IS UNPLUGGED
FROM THE ELECTRICAL OUTLET
BEFORE RELOCATING, SERVICING,
OR CLEANING IT.
WARNING: DO NOT USE THIS
HEATER IN SMALL ROOMS WHEN
THEY ARE OCCUPIED BY PERSONS
NOT CAPABLE OF LEAVING THE
ROOM ON THEIR OWN, UNLESS
CONSTANT SUPERVISION IS
PROVIDED.
WARNING: TO REDUCE THE RISK OF
FIRE, KEEP TEXTILES, CURTAINS, OR
ANY OTHER FLAMMABLE MATERIAL
A MINIMUM DISTANCE OF 1M FROM
THE AIR OUTLET.
CAUTION: THE HEATER WILL
BECOME VERY HOT DURING USE
AND CAN CAUSE BURNS. DO NOT
TOUCH HEATED PARTS OF THE
HEATER WITH BARE SKIN DURING
USE OR IMMEDIATELY AFTER THE
HEATER HAS BEEN SWITCHED
OFF. ALLOW THE HEATER TO
THOROUGHLY COOL DOWN BEFORE
HANDLING OR CLEANING. USE
HANDLE WHEN MOVING THE UNIT.
USE GLOVES OR OVEN MITTS TO
AVOID SERIOUS INJURY.
• Use this heater only as described
in this manual. Any other use not
recommended by the manufacturer may
cause re, electric shock, or injury to
person.
• There may be trace of odour during the
rst few minutes of initial use. This is
normal and will quickly disappear.
• The heater is not to be used by persons
(including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction.
• The heater must have a minimum 50cm
clearance around all sides of the heater.
• Only operate the heater in an upright
position with both foot bases attached.
• Children must be supervised not to play
with the appliance.
• Children of less than 3 years should
be kept away unless continuously
supervised.
• Do not leave children alone or
unattended in the area where the heater
is in use.
• Cleaning and user maintenance shall not
be made by children unless continuously
supervised.
• Place the heater on a at, stable, heat-
resistant surface and always keep the
heater in an upright position. Operating
DIGITAL OIL-FREE RADIATOR
MODEL PB-H14

English | 2
the heater in any other position could
cause a hazard.
• Do not cover, obstruct or push objects
into the vents and opening of the heater
as this may cause an electric shock, re
or damage the heater.
• Do not use this heater to dry or heat
clothes.
• Ensure the heater is not located
immediately below a socket-outlet.
• Never place anything on top of the
heater.
• Do not operate the heater with wet
hands.
• Do not use this heater near water or in
the immediate surroundings of a bath,
shower or a swimming pool. Never
place the heater where it may fall into a
bathtub or other water container.
• Do not allow water or other liquids to
run into the interior of the heater, as
this could create a re and/or electrical
hazard.
• This heater is intended for indoor
household use and similar applications.
Do not use outdoors.
• Never leave the heater unattended while
in use. Always turn the heater o and
disconnected from the power supply
when not in use.
• Do not use the heater while sleeping or
place it near a person who is sleeping.
• Always turn the heater OFF, unplug the
power cord from the electrical outlet
and allow the heater to completely cool
down before handling or cleaning it.
• Avoid placing the power cord in areas
where it can become a tripping hazard.
Do not place the power cord under
carpeting or cover it with rugs, runners
or similar.
• To avoid a circuit overload when using
this heater, do not operate another
high-wattage appliance on the same
electrical circuit.
• Always plug the heater directly into a
wall socket. Avoid using extension leads
where possible as they may overheat
and cause a risk of re.
• Do not use this heater with an external
programmer, timer switch or any other
device which would switch the heater
on automatically unless this has already
been pre-built into the heater by the
manufacturer.
• Do not pull on the power cord. Never
move, carry, or hang the heater by the
power cord.
• Do not kink or wrap the power cord
and plug around the heater, as this
may cause the insulation to weaken
or split, particularly where it enters the
appliance.
• Ensure the mains cable is fully extended
before use and arrange it so that it is not
in contact with any part of the heater.
• The heater should not be used in a
room, of which the oor area is less than
5m².
• Only use this appliance in a well-
ventilated area.
• Do not operate the heater with any
safety guards removed.
• Do not operate the heater if there are
signs of damage to the heater, power
cord, or any of the accessories supplied.
If the supply cord is damaged, it must
be replaced by the manufacturer, its
service agent or a similarly qualied
person in order to avoid a hazard.
• Do not attempt to repair or adjust any
electrical or mechanical elements in the
heater. Doing so may be unsafe and will
void your warranty.
• Ensure that the mains supply (including
voltage, frequency and power) complies
with the rating label of the heater.
• Do not use the heater near petrol,
paints, ammable gases, ovens, or other
heating sources.
• Do not use this heater if it has been
dropped.
• Do not use if there are visible signs of
damage to the heater.

3 | English
BATTERY SAFETY INSTRUCTIONS
――
This remote control is supplied with CR2025
disposable batteries.
PLEASE READ AND SAVE THESE
IMPORTANT SAFETY INSTRUCTIONS
WARNING: CHOKING HAZARD.
DO NOT SWALLOW. HARMFUL
IF SWALLOWED. SWALLOWING
CAN LEAD TO CHEMICAL BURNS,
PERFORATION OF SOFT TISSUE, AND
DEATH. SEVERE BURNS CAN OCCUR
WITHIN 2 HOURS OF INGESTION. IF
YOU SUSPECT YOUR CHILD HAS
SWALLOWED A BATTERY SEEK
MEDICAL ATTENTION IMMEDIATELY.
WARNING: KEEP BATTERIES OUT OF
REACH OF CHILDREN
• This product only uses a CR2025
battery. It is not compatible with other
battery types.
• Do not allow children to handle
batteries.
• Ensure that the battery is installed with
the correct polarity (+ and –).
• Remove exhausted battery promptly.
• Always inspect new batteries before
use. Damaged or weak batteries may
leak acid. Discontinue use if batteries
show signs of leakage, damage, or
weakness at any time.
• Ensure the battery compartment is
correctly and securely closed after
installing the batteries.
• Wash hands after handling batteries.
Disposable batteries are not
rechargeable and must be recycled
or disposed of properly. Do not throw
batteries away with household waste.
Always dispose of batteries at an ocial
collection point.
SPECIFICATION
――
• Model: PB-H14
• Voltage: 220-240V~
• Frequency: 50Hz
• Power: 2000W
• Product Dimensions: L 553 x W 260 x
H 649 mm
• Net Weight: 11.7 kg

English | 4
PARTS
――
Heater
1. Heater body
2. Front handle
3. Control panel
4. Wheel base
5. Rear handle
6. On/o switch
7. Cable storage
8. Remote control
storage slot
Control Panel
1. Thermostat button
2. Increase temperature/time button
3. Mode button
4. Timer button
5. Decrease temperature/time button
6. Stand-by mode button
1
2
3
4
5
6
7
8
1 2 3
4
456
Temperature/hour display
Temperature indicator
Timer hours indicator
Eco mode indicator
Timer indicator

5 | English
Remote Control
1. Mode button
2. Stand-by mode button
3. Timer button
4. Thermostat button
5. Increase temperature/time button
6. Decrease temperature/time button
4
5
1
3
6
2
Note:
• The heater can be controlled by both the
remote control and the control panel.
• A ‘beep’ emits from the control panel
or remote control every time a button is
pressed. To mute this sound, hold down
the increase and decrease buttons for
ve seconds. Repeat to turn the ‘beep’
sound back on.
• The remote can be stored in the ‘remote
control storage slot’ when not in use.
OPERATING INSTRUCTIONS
――
Assembly:
• Turn the body of the heater upside
down on a scratch resistant and stable
surface.
• Place the foot bases over the holes on
each side of the heater.
• Fix the foot bases in place by screwing
in four screws on each side.
Turning the heater on and o:
• Plug the heater in to the wall and ip the
on/o switch to turn the heater on. The
heater is now in stand-by mode and the
stand-by button and timer button will
light up.
• Press the stand-by button. The
appliance will emit a ‘beep’, the rest
of the buttons will light up and the
appliance is ready for use. When the
heater turns on, it will be on its highest
power setting.
• To turn the heater o, press the stand-by
button. The heater will return to stand-
by mode and the control panel screen
will turn o.
• Flip the on/o switch to turn the heater
o completely.

English | 6
Adjusting the heat settings:
• Press the mode button to cycle through
the power modes of high ,
medium , low , and eco mode.
• In eco mode, the ‘ECO’ display will
be lit up and the heater’s power will
automatically adjust to keep the room
at the temperature that has been set
as the thermostat setting. When the
set temperature has been reached,
the heater will turn o. When the room
temperature drops below the set
temperature, it will turn back on again.
Adjusting the thermostat settings:
Note:
• If you don’t set the thermostat, in
eco mode the default thermostat
temperature is 23℃.
• If you set the thermostat temperature,
the heater will be in eco mode
regardless of the power setting you
choose.
• The thermostat temperature setting
range is between 10 °C and 30 °C.
To set the heater’s thermostat, follow the
below steps:
• Press the thermostat button. The
temperature display will start blinking.
• Use the increase and decrease buttons
to set your desired temperature.
• The temperature display will stop
blinking and the chosen temperature
will appear on screen. The heater will
maintain the temperature in the room by
switching on and o automatically.
Setting the timer:
To set a timer for the heater to automatically
turn on, follow the below steps:
• While the heater is in stand-by mode,
press the timer button. The display will
ash ‘0.0’.
• Use the increase and decrease buttons
to set a time between 1 and 24 hours.
The time will increase in 0.5 hour
increments until it reaches 5 hours,
and then it will increase by 1 hour
increments, until it reaches 24 hours.
• The timer button will blink until the time
is set. The number of hours remaining
will show on the display.
• The heater will automatically turn on
when the heater display reaches ‘0.0’
again.
To set a timer for the heater to automatically
turn o, follow the below steps:
• While the heater is on, press the timer
button. The display will ash ‘0.0’.
• Use the increase and decrease buttons
to set a time between 1 and 24 hours.
The time will increase in 0.5 hour
increments until it reaches 5 hours,
and then it will increase by 1 hour
increments, until it reaches 24 hours.
• The heater will automatically turn o
when the heater’s display reaches ‘0.0’.
Your Heater’s Safety Guards:
• Your heater will automatically turn o
when it is not upright. This is to prevent
damage to your home and your heater
will turn back on when it is in its normal
upright position.
• Your heater will automatically turn o
when the appliance has overheated.
This may be because there is something
covering the heater. Unplug the
appliance and wait 30 minutes for it to
cool. If there is no damage to the unit,
cord, or plug, plug the unit back in and
use as normal.

7 | English
CLEANING
――
WARNING: ALWAYS TURN THE
HEATER OFF, UNPLUG THE POWER
CORD FROM THE ELECTRICAL
OUTLET AND ALLOW THE HEATER
TO COMPLETELY COOL DOWN
BEFORE HANDLING OR CLEANING IT.
WARNING: ALLOW THE HEATER TO
COOL DOWN FOR 2 HOURS (240
MINUTES) BEFORE CLEANING.
CAUTION: DO NOT ALLOW WATER
OR OTHER LIQUIDS TO RUN INTO
THE INTERIOR OF THE APPLIANCE,
AS THIS COULD CREATE A FIRE AND/
OR ELECTRICAL HAZARD.
CAUTION: DO NOT USE ANY
ABRASIVE CLEANERS OR SOLVENTS,
AS THIS CAN DAMAGE THE HEATER.
• Do not attempt to clean the appliance in
any other way than that detailed by the
manufacturer.
Your appliance should be cleaned
regularly, following the below instructions:
• Unplug the appliance and let cool before
cleaning.
• Gently clean the outside surface and
the control panel with a damp, lint-free
cloth.
• Clean the vents of the appliance
with a vacuum cleaner and the brush
attachment to avoid dust build-up.
STORAGE
――
• To store your product out of season, we
recommend using the original or similar
size box.
• Store in a clean, dry place away from
direct sunlight. Place out of reach of
children.
RECYCLING & DISPOSAL
――
The packaging of your new heater has a
recycle mark on it. Please dispose of it as
recycled paper. Waste electrical products
should not be disposed of with general
household waste. This is to prevent the
possible harm to the environment and human
well-being. Contact your local council or
government for information regarding the
collection schemes in your area.

English | 8
Model: PB-H14B Symbol Value Unit
Heat output
Nominal heat output Pnom 2.0 kW
Minimum heat output (indicative) Pmin 0.667 kW
Maximum continuous heat output Pmax 2.0 kW
Auxiliary electricity consumption
At nominal heat output elmax N/A kW
At minimum heat output elmin N/A kW
In standby mode elmin 0.00017 kW
Type of heat input, for electric storage local space heaters only (select one)
Manual heat charge control, with integrated thermostat No
Manual heat charge control with room and/or outdoor temperature feedback No
Electronic heat charge control with room and/or outdoor temperature feedback No
Fan assisted heat output No
Type of heat output/room temperature control (select one)
Single stage heat output and no room temperature control No
Two or more manual stages, no room temperature control No
With mechanic thermostat room temperature control No
With electronic room temperature control Yes
Electronic room temperature control plus day timer No
Electronic room temperature control plus week timer No
Other control options (multiple selections possible)
Room temperature control, with presence detection No
Room temperature control, with open window detection No
With distance control option No
With adaptive start control No
With working time limitation Yes
With black bulb sensor No

One Retail Group, Ryland House
24a Ryland Road, Kentish Town, London, NW5 3EH, UK
EU Authorised Representative: Brandrep Limited, The Black Church
St Mary's Pl N, Dublin, D07 P4AX, Ireland
© Copyright 2021