Pro Breeze PB-H16 User manual

Instruction Manual
Model PB-H16
2000W Golden Halogen Lamp Infrared Heater
IMPORTANT INSTRUCTIONS
- RETAIN FOR FUTURE USE

1 | English
2000W Golden Halogen
Lamp Infrared Heater
SAFETY INSTRUCTIONS
Thank you for choosing to purchase a product from ProBreeze. Please read the entire
manual carefully prior to rst use and keep in a safe place for future reference.
WARNING: To avoid the risk of electrical shock, re or injury to people, always
make sure the heater is unplugged from the electrical outlet before installing, relocating,
servicing, or cleaning it.
WARNING: This heater is for domestic outdoor use only. Do not use this heater indoors.
CAUTION: The heater head reaches high temperatures during operation. Do not touch the
heater head when in use. Be aware that the heater head will remain hot for some time after
use. Particular attention must be taken where children and vulnerable people are present.
• Use this heater only as described in this manual. Any other use not recommended by
the manufacturer may cause re, electric shock, or injury to persons.
• The appliance is not to be used by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction.
• The heater must be installed at a minimum hight of 1.8m (180cm) from the oor and
have a 40cm (400mm) clearance from the roof/ceiling.
• A minimum safety distance of 100cm should always be left in front of the heater.
• This heater must be securely xed to a wall using the accessories supplied, prior to use.
• Do not expose the heater to rain or wet conditions. Ensure the heater is shielded from
the weather.
• Children must be supervised not to play with the appliance.
• Children of less than 3 years should be kept away unless continuously supervised.
• Do not leave children alone or unattended in the area where the appliance is in use.
• Cleaning and user maintenance shall not be made by children unless continuously
supervised.
• Do not cover the heater or use this heater to dry or heat clothes or other fabrics.
• Avoid sitting directly underneath the heater.
• This heater should be plugged into a mains power socket which is easily visible and
reachable.
• Don’t use this heater in a place where causticity or volatile air exists, i.e. dust, steam,
gas, etc.
• The heater must not be located immediately below a socket outlet.
• Do not immerse in water or use this heater near water or in the immediate surroundings
of a bath, shower, sauna, or swimming pool.

English | 2
• Never leave the heater unattended while in use. Always turn the heater o and unplug
when not in use.
• Do not place this heater near ammable materials, surfaces or substances. Keep
combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains
at least 3 feet /1m from the heater.
• Use the heater in a well-ventilated area.
• Always turn the heater OFF, unplug the power cord from the electrical outlet and allow
the appliance to completely cool down before handling or cleaning it.
• Never insert ngers or metal objects into the vents and openings of the heater as this
may cause an electric shock, re or damage the heater.
• To avoid a circuit overload when using this heater, do not operate another high-wattage
heater on the same electrical circuit.
• Always plug the heater directly into a wall socket. Avoid using extension leads where
possible as they may overheat and cause a risk of re.
• Do not use this appliance with an external programmer, timer switch or any other device
which would switch the device on automatically unless this has already been pre-built
into the appliance by the manufacturer.
• Do not kink or wrap the power cord and plug around the appliance, as this may cause
the insulation to weaken or split, particularly where it enters the appliance.
• Ensure the mains cable is fully extended before use and arrange it so that it is not in
contact with any part of the appliance.
• Do not pull on the mains cable. Never move, carry or hang the appliance by the mains
cable.
• Do not operate the appliance with any safety guards removed.
• Ensure that the power cord is located so that it will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
• Do not operate the appliance if there are signs of damage to the appliance, power cord,
or any of the accessories.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or a similarly qualied person in order to avoid a hazard.
• Do not attempt to repair or adjust any electrical or mechanical elements in the appliance.
Doing so may be unsafe and will void your warranty.
• Ensure that the mains supply (including voltage, frequency and power) complies with the
rating label of the appliance.
• Do not use the appliance near petrol, paints, ammable gases, ovens, or other heating
sources.
• Do not use the heater indoors or for heavy duty, commercial or industrial use. The unit
is not safe for use on building sites, or in greenhouses, barns or stables where there is
ammable dust.
NOTE: After receiving the product, please test the function before mounting on the wall.

3 | English
Ensure you have all the pieces listed. Do not proceed with set up and assembly of the heater
if any components are missing.
Model: PB-H16
Voltage: 220-240V ~
Frequency: 50/60 Hz
Power: 2000W Max
Product Dimensions: 66*10.5*7.2 CM
Net Weight: 1.67 KG
SPECIFICATION
SET UP - PARTS SUPPLIED
A. 4 pcs explosion screws (M6*60mm)
B. 4 pcs cross-recessed hex screws (M6*10mm)
C. 2 pcs hex screws (M6*12mm)
D. 4 pcs hex nuts (M6)
E. 8 pcs at washers (M6)
F. 8 pcs split lock washers (M5)
G. 2 pcs wing nuts (M6)
H. 4 pcs L shape brackets

English | 4
Note: some equipment may vary based on the assembly space
Estimated Assembly Time: 30 minutes
Batteries: 2 x AAA batteries required. Not included.
IP 65 Approved when used with IP65 rated socket.
IMPORTANT: When drilling into walls always check that there are no hidden wires or pipes.
Ensure that the screws and wall plugs being used are suitable for supporting the unit to be
installed. If you are unsure it is recommended you contact a suitable qualied tradesperson.
Set up the heater outside, or in a large open area and well away from any obstructions such
as tree branches.
SET UP - EQUIPMENT REQUIRED
SET UP & FIRST USE
• Phillips screw driver
• 8mm spanner
• 10mm spanner
• Drill & masonry drill bit (8mm diameter).
• Ladder
• Hammer
• Pen or marker
• Ruler

5 | English
WARNING
• The heater should always be installed horizontally, only using the mounting brackets
supplied.
• Ensure the supply cable is well mounted and that it does not touch the reector on the
heater.
• Ensure the supply cable does not trail in front of the heater while it is in operation.
• The supply cable can be xed to the metal mounting bracket behind the heater with
plastic zip ties.
ASSEMBLING INSTRUCTIONS
Ensure the heater is not facing the ceiling or inammable substances.
NOTE: Two dark points may appear on the surface of the heating elements during the rst
few minutes after the heater is turned on. This is normal and will not aect the performance
of the heater.

English | 6
Step 1: Connect 2 L brackets (H) to the heater as shown. Do this using a Phillips screwdriver
with 4 components of B, E & F (see order pictured).
Step 2: With remaining L brackets (H) connect explosion screws as shown. This can be done
by hand, using components (A, D, E, F).
HOW TO ASSEMBLE THE UNIT

7 | English
Step 1: On the L shaped Brackets (H), measure the pitch between the pair of holes desired
for use, with a ruler.
Step 2: Using a pen, mark the same distance where you are going to drill (determine hole
depth before hand).
Step 3: Using power drill and 8mm masonry drill bit, drill holes.
ENSURE THERE ARE NO WIRES OR PIPES BEHIND WALL.
Step 4: Fit explosion screws into wall, tighten nut D. Tighten each nut individually, a small
amount each until unit is rmly anchored.
Step 5: Connect heater attached L Brackets to explosion screw L Brackets (tted into
wall) using components C & G as shown. Use 10mm spanner if necessary.
HOW TO ATTACH TO WALL/CEILING

English | 8
WALL ANGLE
• Do not face heater at 90° towards ceiling.
• Only face downwards at maximum angle 135° see below.
OPERATING ANGLE
CEILING ANGLE
• Do not face heater at 90° towards walls.
• Do not face fan directly down 180°. Only face at 135° angles.
OPERATING INSTRUCTIONS

9 | English
NOTE: Ensure the rocker switch is set to “ON” before using the remote.
• SwitchOn/OButton- To switch on the heater, press the rocker switch to the On
position
• ModeSwitchButton-Press the mode button to alternate between three dierent
modes. For each mode, the LED light indicator will illuminate a dierent colour:
• Red: The heater is in the standby mode.
• Green: The heater is in the low heat mode.
• Blue:The heater is the high heat mode.
• Remote Control

English | 10
This marking indicates that this product should not be disposed of with other
household waste throughout the EU. This is to prevent possible harm to the
environment and human wellbeing. Contact your local authority for information
regarding the collection systems available. If possible, recycle it responsibly to
promote the sustainable reuse of resources.
DISPOSAL
WARNING: Always turn the heater OFF, unplug the power cord from the electrical outlet and
allow the appliance to completely cool down before handling or cleaning it. Allow the heater
to cool down for 2 hours (120 minutes) before cleaning.
CAUTION: Do not allow water or other liquids to run into the interior of the heater, as this
could create a re and/or electrical hazard.
CAUTION: Do not use any abrasive cleaners or solvents, as heater damage will occur.
IMPORTANT: The bulb inside the heater is not replaceable. Do not attempt to remove or
disassemble the heater.
• Clean the exterior surface of the heater by wiping it with a soft, damp cloth. Dry the
heater with a soft clean cloth.
• Clean the vents and openings of the heater with a vacuum cleaner, using the brush
attachment to avoid any dust build-up.
• To store your product out of season, we recommend using the original or similar size
box.
• Do not kink or wrap the power cord and plug around the appliance, as this may cause
the insulation to weaken or split, particularly where it enters the appliance.
• Store the heater in a safe, clean and dry place when not in use.
CLEANING, MAINTANANCE & STORAGE

One Retail Group, Ryland House
24a Ryland Road, London, NW5 3EH, United Kingdom
EU Authorised Representative: Brandrep Limited, The Black Church
St Mary's Pl N, Dublin, D07 P4AX, Ireland
© Copyright 2021